1. Manuals
  2. Brands
  3. Berkel Manuals
  4. Food Processor
  5. CC34
  6. Service manual

Berkel CC34 Service Manual

Hide thumbs Also See for CC34:
Table of Contents

Advertisement

Quick Links

See also: Owner's/operator's Manual
This Manual is prepared for the use of trained Berkel Service
Technicians and should not be used by those not properly
qualified.
This manual is not intended to be all encompassing. If you have
not attended a Berkel Service School for this product, you should
read, in its entirety, the repair procedure you wish to perform to
determine if you have the necessary tools, instruments and skills
required to perform the procedure. Procedures for which you do
not have the necessary tools, instruments and skills should be
performed by a trained Berkel Service Technician.
The reproduction, transfer, sale or other use of this Manual,
without the express written consent of Berkel, is prohibited.
This manual has been provided to you by ITW Food Equipment
Group LLC ("ITW FEG") without charge and remains the property
of ITW FEG, and by accepting this manual you agree that you will
return it to ITW FEG promptly upon its request for such return at
any time in the future.
A product of Berkel
SERVICE MANUAL
Food Processer
CC34
B32
C32
- NOTICE -
F25264 (0116)

Advertisement

Table of Contents
loading

Related Manuals for Berkel CC34

Summary of Contents for Berkel CC34

  • Page 1 Food Processer CC34 - NOTICE - This Manual is prepared for the use of trained Berkel Service Technicians and should not be used by those not properly qualified. This manual is not intended to be all encompassing. If you have...

  • Page 2: Table Of Contents

    TROUBLESHOOTING ................. 13 © BERKEL 2016...

  • Page 3: General

    Food Processer - GENERAL GENERAL INTRODUCTION LUBRICATION This manual covers Models CC34, B32, and C32 Chevron FM ALC EP - 2 used in bowl drive gear case. Food Processors. SPECIFICATIONS Operating voltage 100-120/50-60/1 Current 10 amps CLEANING PROCEDURES Never clean machine with a high pressure hose, with steam injection equipment or in a dishwasher.

  • Page 4: Removal And Replacement Of Parts

    Food Processer - REMOVAL AND REPLACEMENT OF PARTS REMOVAL AND REPLACEMENT OF PARTS BASE AND TOP HOUSING Disconnect the electrical power to the machine and follow lockout / tagout procedures. Remove cutter/mixer bowl or feeder attachment. Position unit on blocks as shown to protect knife shaft from damage during disassembly.

  • Page 5: Control Board

    Food Processer - REMOVAL AND REPLACEMENT OF PARTS Remove motor, bracket, and wires from top housing. NOTE: During motor installation, be sure to align drive belt correctly. The motor drive shaft should be inside the drive belt; the belt tensioner should be on the outside of the belt.
  • Page 6 Food Processer - REMOVAL AND REPLACEMENT OF PARTS Remove screw pin from knife shaft. NOTE: Some heat may be required to remove the screw pin. Remove seal ring from knife shaft. Fig. 8 Remove drive belt, screw, washer, and knife shaft pulley.

  • Page 7: Magnetic Safety Switch

    Food Processer - REMOVAL AND REPLACEMENT OF PARTS Fig. 13 Fig. 15 14. Remove ring seal from top housing. Install magnetic safety switch in reverse order of removal. SPEED CONTROL SWITCH Disconnect the electrical power to the machine and follow lockout / tagout procedures. Remove base housing as outlined under BASE AND TOP HOUSING.

  • Page 8: Rotary Switch

    Food Processer - REMOVAL AND REPLACEMENT OF PARTS ROTARY SWITCH MICROSWITCH Disconnect the Disconnect the electrical power to the machine and electrical power to the machine and follow lockout / tagout procedures. follow lockout / tagout procedures. Remove base housing as outlined under BASE Remove base housing as outlined under BASE AND TOP HOUSING.
  • Page 9 Food Processer - REMOVAL AND REPLACEMENT OF PARTS Fig. 21 Install microswitch in reverse order of removal. Page 9 of 13 F25264 (0116)

  • Page 10: Service Procedures And Adjustments

    Food Processer - SERVICE PROCEDURES AND ADJUSTMENTS SERVICE PROCEDURES AND ADJUSTMENTS ELECTRICAL CONTROLS TEST MOTOR TEST PROCEDURES Certain procedures in Do not install any cutting tools for te this section require electrical test or following tests. measurements while power is applied Remove the feeder, any cutting tools and ejector to the machine.

  • Page 11: Electrical Operation

    Food Processer - ELECTRICAL OPERATION ELECTRICAL OPERATION COMPONENT FUNCTION Motor - M1 Drive Motor Speed Sensor Fixed Value Inductor Monitors speed of blade rotation. Safety Interlock 1LS Keeps motor from turning if feeder is not installed properly. Speed Selector Allows operator to select preferred speed. Senses which attachment is installed and automatically sets speed Magnetic Switch Speed Control ranges.

  • Page 12: Wiring Diagram

    Food Processer - ELECTRICAL OPERATION WIRING DIAGRAM Fig. 24 F25264 (0116) Page 12 of 13...

  • Page 13: Troubleshooting

    TROUBLESHOOTING TROUBLESHOOTING To eliminate the risk of damage to the motor, the CC34, B32, and C32 are fitted with thermal motor protection that automatically switches off the machine if the temperature of the motor should become too high. The thermal motor protection has automatic reset, which means that the machine can be started again when the motor has cooled down, which usually takes between 10 and 30 minutes.

This manual is also suitable for:

B32C32

Table of Contents