Becker DTM High Speed 7910 Installation Manual
Hide thumbs
Also See for DTM High Speed 7910:
- Operating manual (4 pages) ,
- Operating manual (77 pages)
Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Operating Manual
Installation guide
Contents
1.
Prior to installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
2.
Symbols used in the installation guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
3.
Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
4.
Installation instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
5.
Connection diagram for the navigation system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
6.
Installation of the GPS antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
7.
Connecting the reverse signal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
8.
Connecting the speed signal (GAL) for the speedometer / speedometer cable . . . . . . . . . . . 35
9.
Installing and commissioning DTM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
10. Using GPS for the first time, and sensors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
11. Installation of the Navigation Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
12. Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
13. Service Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
14. Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
1. Prior to installation
Before starting installation, please read this installation guide carefully. In particular, please pay attention to the safety
and installation instructions.
Subject to correction and technical modifications
28
Copyright by Becker GmbH, D-76303 Karlsbad
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Becker DTM High Speed 7910
Summary of Contents for Becker DTM High Speed 7910
-
Page 1: Table Of Contents
14. Connections ............. . 53 1. Prior to installation Before starting installation, please read this installation guide carefully. In particular, please pay attention to the safety and installation instructions. Subject to correction and technical modifications Copyright by Becker GmbH, D-76303 Karlsbad... -
Page 2: Symbols Used In The Installation Guide
Risk of injury due to inadequate fastening Fix the components in place so that they cannot be loosened in the event of a collision or sudden braking. Subject to correction and technical modifications Copyright by Becker GmbH, D-76303 Karlsbad... -
Page 3: Installation Instructions
In order to avoid malfunctions, it is absolutely essential to observe the relevant cable cross-section when using branch connections/cable connectors. In order to avoid short-circuits and any associated risk of fire, cables which have to be cut must be properly insulated. Subject to correction and technical modifications Copyright by Becker GmbH, D-76303 Karlsbad... -
Page 4: Connection Diagram For The Navigation System
Radio aerial Speedometer / speedometer cable signal Sound system / loudspeaker GPS antenna Reverse signal Power supply Note: The various connection options are described in detail on page 53. Subject to correction and technical modifications Copyright by Becker GmbH, D-76303 Karlsbad... -
Page 5: Installation Of The Gps Antenna
The maximum vehicle speed for the antenna if magnetically attached is 180 km/h. The antenna must be removed or specially secured at higher speeds. The antenna is not suitable for car-wash facilities. Subject to correction and technical modifications Copyright by Becker GmbH, D-76303 Karlsbad... - Page 6 Remove protective strip from bottom of adhesive tape (2) and stick the antenna and base plate onto the vehicle console beneath the windscreen at the installation position. Subject to correction and technical modifications Copyright by Becker GmbH, D-76303 Karlsbad...
-
Page 7: Connecting The Reverse Signal
Connect a separate lead to the activated lead of the reversing lamp and connect to socket A pin 2. Subject to correction and technical modifications Copyright by Becker GmbH, D-76303 Karlsbad... -
Page 8: Connecting The Speed Signal (Gal) For The Speedometer / Speedometer Cable
Low - level < 1.5 V, high - level 5 V - 16 V If you do not know the exact installation position / location of the speed signal, please consult the vehicle manufacturer. Subject to correction and technical modifications Copyright by Becker GmbH, D-76303 Karlsbad... - Page 9 If the sealed speedometer cable is released, a correct display cannot be guaranteed. Incorrect installation leads to improper functioning of the navigation system or of the speedometer. Subject to correction and technical modifications Copyright by Becker GmbH, D-76303 Karlsbad...
- Page 10 2 x fuel washers 4.0 KN07.0570.18 (VDO part number) 2 x washers KN11.1904.122 (VDO part number) An appropriate, complete kit from VDO (part number X 39397106191) can also be used. Subject to correction and technical modifications Copyright by Becker GmbH, D-76303 Karlsbad...
- Page 11 Connect the union nut and hose sleeve (Figure 6) and push onto the hose ends (Figure 7). Figure 6 • Connect friction washer to dog (Figure 8). Figure 7 Figure 8 Figure 8 Subject to correction and technical modifications Copyright by Becker GmbH, D-76303 Karlsbad...
- Page 12 Wire connections for the speed sensor Brown earth (terminal 31) Black power supply (terminal 15), 9 - 16V, 30 mA Blue/red - signal for socket A pin 1 Subject to correction and technical modifications Copyright by Becker GmbH, D-76303 Karlsbad...
-
Page 13: Installing And Commissioning Dtm
The number under must change (even at a low speed). The number under should not increase when idling or V M N pressing the accelerator when the vehicle is parked. Subject to correction and technical modifications Copyright by Becker GmbH, D-76303 Karlsbad... - Page 14 (clear view in all directions as far as possible) or the installation location of the GPS antenna must be checked. Subject to correction and technical modifications Copyright by Becker GmbH, D-76303 Karlsbad...
-
Page 15: Installation Of The Navigation Software
The adjacent display appears after installation. Then press the right rotary control to confirm. The language selection can be changed at a later time, as de- scribed in the operating guide. Subject to correction and technical modifications Copyright by Becker GmbH, D-76303 Karlsbad... -
Page 16: Calibration
However: a lower accuracy of the GPS signal (2-D FIX) does not lead to a poorer calibration, but in- stead will mean that the time and distance needed for the cali- bration will increase. Subject to correction and technical modifications Copyright by Becker GmbH, D-76303 Karlsbad... - Page 17 If the unit is switched off during the calibration ride, language installation is requested when the unit is switched on again. Re- installation can be skipped by pressing the button. Subject to correction and technical modifications Copyright by Becker GmbH, D-76303 Karlsbad...
-
Page 18: Service Mode
• Press and hold the multifunction buttons. Then press the multifunction button. This calls up the Service Mode. Subject to correction and technical modifications Copyright by Becker GmbH, D-76303 Karlsbad... - Page 19 A certain amount of time may be required to reach this value (do not move the vehicle during this period). In order to quit the GPS test, press the button. The unit switches back to the Service Mode. Subject to correction and technical modifications Copyright by Becker GmbH, D-76303 Karlsbad...
- Page 20 Using the right rotary control select and press to confirm. Unit rotation can be selected in degrees by turning the right rotary control and pressing to confirm. Subject to correction and technical modifications Copyright by Becker GmbH, D-76303 Karlsbad...
- Page 21 D To enter the tyre data, select by turning the right rotary control and press to confirm. Subject to correction and technical modifications Copyright by Becker GmbH, D-76303 Karlsbad...
- Page 22 After a short time, the unit switches to the main navigation menu or the calibration ride is requested. The unit is now in calibration status 2. Absolute precision is, however, only achieved as of calibration status 3. Subject to correction and technical modifications Copyright by Becker GmbH, D-76303 Karlsbad...
- Page 23 The number after should increase (even at a low speed). The number after should not increase if idling or press- ing the accelerator when the vehicle is parked. Subject to correction and technical modifications Copyright by Becker GmbH, D-76303 Karlsbad...
- Page 24 The announcement "Please insert Navigation CD" is given. By pressing the right rotary control , the announcement can be repeated. After completing the test, press the button. The unit switches back to the Service Mode. Subject to correction and technical modifications Copyright by Becker GmbH, D-76303 Karlsbad...
- Page 25 You can now enter a destination as described in the operation guide. • To switch off the demo mode, select with the right rotary control and press to confirm. Subject to correction and technical modifications Copyright by Becker GmbH, D-76303 Karlsbad...
-
Page 26: Connections
LineOut front right Illumination (terminal 58) Subwoofer LineOut Switched positive (terminal 15) Socket C2 Earth (terminal 31) 7-12 Special connection for Becker CD changer Socket B Socket C3 Loudspeaker rear right + Loudspeaker rear right - AF telephone input Loudspeaker front right +...
Need help?
Do you have a question about the DTM High Speed 7910 and is the answer not in the manual?
Questions and answers