Table of Contents
Advertisement
Copyright
This publication, including all photographs, illustrations and software, is protected
under international copyright laws, with all rights reserved. Neither this manual, nor
any of the material contained herein, may be reproduced without written consent of
the author.
Version 1.0
Disclaimer
The information in this document is subject to change without notice. The manufac-
turer makes no representations or warranties with respect to the contents hereof and
specifically disclaims any implied warranties of merchantability or fitness for any
particular purpose. The manufacturer reserves the right to revise this publication and
to make changes from time to time in the content hereof without obligation of the
manufacturer to notify any person of such revision or changes.
Trademark Recognition
Microsoft, MS-DOS and Windows are registered trademarks of Microsoft Corp.
MMX, Pentium, Pentium-II, Pentium-III, Celeron are registered trademarks of Intel
Corporation.
Other product names used in this manual are the properties of their respective
owners and are acknowledged.
Federal Communications Commission (FCC)
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installa-
tion. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful inter-
ference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
•
Reorient or relocate the receiving antenna
•
Increase the separation between the equipment and the receiver
•
Connect the equipment onto an outlet on a circuit different from that to
which the receiver is connected
•
Consult the dealer or an experienced radio/TV technician for help
Shielded interconnect cables and a shielded AC power cable must be employed with
this equipment to ensure compliance with the pertinent RF emission limits governing
this device. Changes or modifications not expressly approved by the system's manu-
facturer could void the user's authority to operate the equipment.
Preface
Preface
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for ECS P55H-A2
Summary of Contents for ECS P55H-A2
- Page 1 Preface Copyright This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author. Version 1.0 Disclaimer The information in this document is subject to change without notice.
-
Page 2: Declaration Of Conformity
Declaration of Conformity This device complies with part 15 of the FCC rules. Operation is subject to the following conditions: • This device may not cause harmful interference, and • This device must accept any interference received, including interfer- ence that may cause undesired operation Canadian Department of Communications This class B digital apparatus meets all requirements of the Canadian Interference- causing Equipment Regulations. -
Page 3: Table Of Contents
T T T T T ABLE OF CONTENTS ABLE OF CONTENTS ABLE OF CONTENTS ABLE OF CONTENTS ABLE OF CONTENTS Preface Chapter 1 Introducing the Motherboard Introduction...................1 Feature....................2 Specifications................4 Motherboard Components............5 Chapter 2 7 7 7 7 7 Installing the Motherboard Safety Precautions................7 Choosing a Computer Case............7 Installing the Motherboard in a Case...........7... - Page 4 Using BIOS..................29 Standard CMOS Setup............30 Advanced Setup..............32 Advanced Chipset Setup............34 Integrated Peripherals............34 Power Management Setup.............36 PCI/PnP Setup..............37 PC Health Status..............38 M.I.B.II (MB Intelligent BIOSII)...........42 Load Default Settings............44 Supervisor Password............44 User Password..............45 Save & Exit Setup..............45 Exit Without Saving...............45 Updating the BIOS..............46 47 47 47 47 47 Chapter 4 Using the Motherboard Software...
- Page 5 Chapter 6 57 57 57 57 57 Setting Up eJIFFY Introduction..................57 Installation and BIOS Setup............58 Entering eJIFFY ..................Features Icons ..................Usage FAQ ..63 .................... Chapter 7 75 75 75 75 75 Trouble Shooting Start up problems during assembly...........75 Start up problems after prolong use..........76 Maintenance and care tips..............76 Basic Troubleshooting Flowchart............77...
- Page 6 Memo...
-
Page 7: Introducing The Motherboard
Chapter 1 Introducing the Motherboard Introduction Thank you for choosing the P55H-A2 motherboard. This motherboard is a high performance, enhanced function motherboard designed to support the LGA1156 ® socket for Intel Lynnfield/Clarkdale processors for high-end business or personal desktop markets. ®... -
Page 8: Feature
Feature Processor The motherboard uses an LGA1156 type of socket that carries the following features: ® • Accommodates Intel Lynnfield/Clarkdale processors • Supports “Hyper-Threading” technology CPU “Hyper-Threading” technology enables the operating system into thinking it’s hooked up to two processors, allowing two threads to be run in parallel, both on separate “logical”... -
Page 9: Onboard Lan
• CPU parameters • CPU and memory timing • ECS M.I.B.II BIOS The firmware can also be used to set parameters for different processor clock speeds. 1. Some hardware specifications and software items are subject to change without prior notice. -
Page 10: Specifications
Specifications ® • CPU LGA1156 socket for latest Intel Lynnfield/Clarkdale processors • Supports “Hyper-Threading” technology CPU Chipset • Intel P55 Express Chipset Memory • Dual-channel DDR3 memory architecture • 4 x 240-pin DDR3 DIMM sockets support up to 16 GB •... -
Page 11: Motherboard Components
Motherboard Components Table of Motherboard Components LABEL COMPONENTS ® 1. CPU Socket LGA1156 socket for Intel Lynnfield/Clarkdale processors 2. DDR3_1~4 240-pin DDR3 SDRAM slots 3. ATX_POWER Standard 24-pin ATX power connector 4. SYS_FAN System cooling fan connector 5. SATA1~6 Serial ATA connectors 6. - Page 12 Memo Introducing the Motherboard...
-
Page 13: Installing The Motherboard
Chapter 2 Installing the Motherboard Safety Precautions • Follow these safety precautions when installing the motherboard • Wear a grounding strap attached to a grounded device to avoid dam- age from static electricity • Discharge static electricity by touching the metal case of a safely grounded object before working on the motherboard •... -
Page 14: Checking Jumper Settings
Do not over-tighten the screws as this can stress the motherboard. Checking Jumper Settings This section explains how to set jumpers for correct configuration of the motherboard. Setting Jumpers Use the motherboard jumpers to set system configuration options. Jumpers with more than one pin are numbered. -
Page 15: Checking Jumper Settings
Checking Jumper Settings The following illustration shows the location of the motherboard jumpers. Pin 1 is labeled. Jumper Settings Type Jumper Description Setting (default) 1-2: NORMAL 2-3: CLEAR CMOS CLR_CMOS 3-pin Clear CMOS Before clearing the CLR_CMOS CMOS, make sure to turn off the system. -
Page 16: Installing Hardware
Installing Hardware Installing the Processor Caution: When installing a CPU heatsink and cooling fan make sure that you DO NOT scratch the motherboard or any of the surface-mount resis- tors with the clip of the cooling fan. If the clip of the cooling fan scrapes across the motherboard, you may cause serious damage to the motherboard or its components. -
Page 17: Cpu Installation Procedure
CPU Installation Procedure The following illustration shows CPU installation components. A. Opening of the Load Plate · Put your thumb on the tail of the load plate and press the tail down. · Rotate the load plate to fully open position. -
Page 18: Installing Memory Modules
1. To achieve better airflow rates and heat dissipation, we suggest that you use a high quality fan with 3800 rpm at least. CPU fan and heatsink installation procedures may vary with the type of CPU fan/ heatsink supplied. The form and size of fan/heatsink may also vary. 2. -
Page 19: Installation Procedure
1. For best performance and compatibility, we recommend that users give priority to the yellow DIMMs (DDR3_2/DDR3_4) when install- ing DIMMs. 2. We suggest users not mix memory type. It is recommended to use the same brand and type memory on this motherboard. Do not remove any memory module from its antistatic packaging until you are ready to install it on the motherboard. - Page 20 Table A: DDR3 (memory module) QVL (Qualified Vendor List) The following DDR3 2133 (OC)/1800/1600/1333/1066 memory modules have been tested and qualified for use with this motherboard. Type Size Vendor Module Name ELPIDA PC3-8500U-7-00-AP HYMT112U64ZNF8-G8 AA Hynix HMT112U6AFP8C-G7N0 AA Kingston KVR1066D3N7/1G 512 MB MT8JTF12864AY-1G1D1 Micron...
- Page 21 1 GB Kingston KHX14400D3K3/3GX DDR3 2133 2 GB Kingston FLGE85F-B8KG9 NEES User please be noted that DDR3 2133/1800/1600MHz is validated to run at 1333Mhz only. Suggest to use XMP module and ECS MIB II BIOS for better performance. Installing the Motherboard...
-
Page 22: Expansion Slots
Expansion Slots Installing Add-on Cards The slots on this motherboard are designed to hold expansion cards and connect them to the system bus. Expansion slots are a means of adding or enhancing the motherboard’s features and capabilities. With these efficient facilities, you can in- crease the motherboard’s capabilities by adding hardware that performs tasks that are not part of the basic system. - Page 23 Follow these instructions to install an add-on card: Remove a blanking plate from the system case corresponding to the slot you are going to use. Install the edge connector of the add-on card into the expansion slot. Ensure that the edge connector is correctly seated in the slot. Secure the metal bracket of the card to the system case with a screw.
-
Page 24: Connecting Optional Devices
Connecting Optional Devices Refer to the following for information on connecting the motherboard’s optional devices: F_AUDIO: Front Panel Audio header This header allows the user to install auxiliary front-oriented microphone and line- out ports for easier access. Signal Name Signal Name PORT 1L AUD_GND PORT 1R... - Page 25 F_USB1~3: Front Panel USB headers The motherboard has eight USB ports installed on the rear edge I/O port array. Additionally, some computer cases have USB ports at the front of the case. If you have this kind of case, use auxiliary USB connector to connect the front-mounted ports to the motherboard.
-
Page 26: Installing A Hard Disk Drive
Red: FULL LOAD Yellow: NORMAL LOAD Green: LOW LOAD Green: LIGHT LOAD Installing a SATA Hard Drive This section describes how to install SATA devices. About SATA Connectors Your motherboard features six SATA connectors supporting a total of six drives. SATA refers to Serial ATA (Advanced Technology Attachment) is the standard inter- face for the IDE hard drives which are currently used in most PCs. -
Page 27: Connecting I/O Devices
Connecting I/O Devices The backplane of the motherboard has the following I/O ports: PS2 Mouse Use the upper PS/2 port to connect a PS/2 pointing device. PS2 Keyboard Use the lower PS/2 port to connect a PS/2 keyboard. Serial Port Use the COM port to connect serial devices such as mice or (COM) fax/modems. -
Page 28: Connecting Case Components
Connecting Case Components After you have installed the motherboard into a case, you can begin connecting the motherboard components. Refer to the following: Connect the CPU cooling fan cable to CPU_FAN. Connect the system cooling fan connector to SYS_FAN. Conect the case speaker cable to SPK Connect the power cooling fan connector to PWR_FAN. - Page 29 2. Connecting 4-pin power cable Users please note that the 4-pin power cables can be connected to the ATX12V connector. When installing 4-pin power cable, the latch falls on the left side of the ATX12V connec- tor. 4-pin power cable CPU_FAN: CPU cooling FAN Power Connector Signal Name Function...
- Page 30 PWR_FAN: FAN Power Connector Signal Name Function System Ground Power +12V +12V Sense Sensor ATX_ POWER: ATX 24-pin Power Connector Signal Name Signal Name +3.3V +3.3V +3.3V -12V Ground Ground PS_ON Ground Ground Ground Ground Ground PWRGD +5VSB +12V +12V +3.3V Ground ATX12V: ATX 12V Power Connector...
-
Page 31: Front Panel Header
Front Panel Header The front panel header (F_PANEL) provides a standard set of switch and LED headers commonly found on ATX or Micro ATX cases. Refer to the table below for information: Signal Function Signal Function HD_LED_P Hard disk LED(+) 2 FP PWR/SLP *MSG LED(+) HD_LED_N Hard disk LED(- ) FP PWR/SLP *MSG LED(-) - Page 32 Memo Installing the Motherboard...
-
Page 33: Using Bios
Chapter 3 Using BIOS About the Setup Utility The computer uses the latest “American Megatrends Inc. ” BIOS with support for Windows Plug and Play. The CMOS chip on the motherboard contains the ROM setup instructions for configuring the motherboard BIOS. The BIOS (Basic Input and Output System) Setup Utility displays the system ’... -
Page 34: Resetting The Default Cmos Values
Press the delete key to access the BIOS Setup Utility. CMOS Setup Utility -- Copyright (C) 1985-2009, American Megatrends, Inc. Standard CMOS Setup M.I.B. II(MB Intelligent BIOS II) Advanced Setup Load Default Settings Advanced Chipset Setup Supervisor Password Integrated Peripherals User Password Power Management Setup Save &... -
Page 35: Using Bios
Using BIOS When you start the Setup Utility, the main menu appears. The main menu of the Setup Utility displays a list of the options that are available. A highlight indicates which option is currently selected. Use the cursor arrow keys to move the highlight to other options. -
Page 36: Standard Cmos Setup
For the purpose of better product maintenance, the manufacture reserves the right to change the BIOS items presented in this manual. The BIOS setup screens shown in this chapter are for reference only and may differ from the actual BIOS. Please visit the manufacture’s website for updated manual. - Page 37 Type (Auto) Use this item to configure the type of the IDE device that you specify. If the feature is enabled, it will enhance hard disk performance by reading or writing more data during each transfer. LBA/Large Mode (Auto) Use this item to set the LBA/Large mode to enhance hard disk performance by optimizing the area the hard disk is visited each time.
-
Page 38: Advanced Setup
APIC Mode Enabled 1st Boot Device Hard Drive 2nd Boot Device CD/DVD 3rd Boot Device Removable Dev. Boot Other Device ECS eJIFFY Function Disabled : Move F10: Save ESC: Exit Enter : Select +/-/: Value F1:General Help F9: Optimized Defaults Thermal Management (Enabled) This item displays CPU’s temperature and enables you to set a safe temperature to... - Page 39 ECS eJIFFY Function (Disabled) Use this item to enable or disable the ECS eJIFFY Function. eJIFFY is ECS unique software program for the quick access to the internet without entering O.S. Please refer to Chapter 6 to know more about eJIFFY.
-
Page 40: Advanced Chipset Setup
Advanced Chipset Setup This page sets up more advanced information about your system. Handle this page with caution. Any changes can affect the operation of your computer. CMOS Setup Utility - Copyright (C) 1985-2009, American Megatrends, Inc. Advanced Chipset Setup Help Item Memory Remap Feature Enabled... - Page 41 OnBoard SATA Mode (Enhanced) Use this item to show the Serial ATA Configuration options: Disabled, Compatible, Enhanced. Onboard SATA2 Controller (AHCI Mode) Use this item to select the mode of the Onboard SATA2 Controller. OnBoard AUDIO Function (Enabled) Use this item to enable or disable the onboard Audio function. OnBoard LAN Function (Enabled) Use this item to enable or disable the onboard LAN function.
-
Page 42: Power Management Setup
Power Management Setup This page sets up some parameters for system power management operation. CMOS Setup Utility - Copyright (C) 1985-2009, American Megatrends, Inc. Power Management Setup Help Item ACPI Suspend Type PWRON After PWR-Fail Power Off Select the ACPI Resume by Ring Disabled state used for... -
Page 43: Pci/Pnp Setup
Resume on RTC Alarm (Disabled) The system can be turned off with a software command. If you enable this item, the system can automatically resume at a fixed time based on the system’s RTC (realtime clock). Use the items below this one to set the date and time of the wake-up alarm. You must use an ATX power supply in order to use this feature. -
Page 44: Pc Health Status
PC Health Status On motherboards support hardware monitoring, this item lets you monitor the parameters for critical voltages, temperatures and fan speeds. CMOS Setup Utility - Copyright (C) 1985-2009, American Megatrends, Inc. PC Health Status Help Item -=- System Hardware Monitor-=- Smart Fan Function Press Enter System Temperature... - Page 45 SMART Fan Mode (Normal) This item allows you to select the fan mode (Normal, Quiet, Silent, or Manual) for a better operation environment. If you choose Normal mode, the fan speed will be auto adjusted depending on the CPU temperature. If you choose Quite mode, the fan speed will be auto minimized for quiet environment.
- Page 46 CMOS Setup Utility - Copyright (C) 1985-2009, American Megatrends, Inc. Smart Fan Function Help Item SMART Fan Function Enabled Smart Fan Mode Silent Options CPU SMART Fan start PWM Normal: auto adjusts SMART Fan start PWM TEMP(-) depending on the CPU DeltaT temperature.
- Page 47 ECS supports the latest PECI host technology. While using Lynnfield CPU, the original images of the BIOS item “PC Health Status” and “Smart FAN Function” will be replaced by PECI mode and negative number. (The max data from PECI is zero.) CMOS Setup Utility - Copyright (C) 1985-2009, American Megatrends, Inc.
-
Page 48: M.i.b.ii (Mb Intelligent Biosii)
Shutdown Temperature (Disabled) Enable you to set the maximum temperature the system can reach before powering down System Component Characteristics These items display the monitoring of the overall inboard hardware health events, such as System & CPU temperature, CPU & DIMM voltage, CPU & system fan speed,...etc. - Page 49 Performance Level (Standard) This item shows the performance level of the components, the options are: Standard and Enhanced. DRAM Frequency (Auto) This item enables users to adjust the DRAM frequency. The default setting is auto and we recommend users leave the setting unchanged. Modify it at will may cause the system to be unstable.
-
Page 50: Load Default Settings
VDIMM (1.504 V) This item displays the current DIMM voltage. CPU VTT Voltage (1.152V) This item allows users to adjust the CPU VTT voltage. Warning: Please pay attention that doing overvoltage may result in damage to hardware. Press <Esc> to return to the main menu setting page. Load Default Settings This option opens a dialog box to ask if you are sure to install optimized defaults or not. -
Page 51: User Password
User Password This page helps you install or change a password. CMOS Setup Utility - Copyright (C) 1985-2009, American Megatrends, Inc. User Password User Password : Not Installed Help item : Move F10: Save ESC: Exit Enter : Select +/-/: Value F1:General Help F9: Optimized Defaults User Password (Not Installed) -
Page 52: Updating The Bios
Updating the BIOS You can download and install updated BIOS for this motherboard from the manufacturer’s Web site. New BIOS provides support for new peripherals, improve- ments in performance, or fixes for known bugs. Install new BIOS as follows: If your motherboard has a BIOS protection jumper, change the setting to allow BIOS flashing. -
Page 53: Using The Motherboard Software
Chapter 4 Using the Motherboard Software About the Software DVD-ROM/CD-ROM The support software DVD-ROM/CD-ROM that is included in the motherboard pack- age contains all the drivers and utility programs needed to properly run the bundled products. Below you can find a brief description of each software program, and the location for your motherboard version. -
Page 54: Running Setup
Drivers Tab Setup Click the Setup button to run the software installation program. Select from the menu which software you want to install. Browse CD The Browse CD button is the standard Windows command that allows you to open Windows Explorer and show the contents of the support disk. - Page 55 Click Next. The following screen appears: Check the box next to the items you want to install. The default options are recom- mended. Click Next run the Installation Wizard. An item installation screen appears: Follow the instructions on the screen to install the items. Drivers and software are automatically installed in sequence.
-
Page 56: Manual Installation
Windows Vista/7 will appear below UAC (User Account Control) message after the system restart. You must select “Allow” to install the next driver. Continue this process to complete the drivers installation. Manual Installation Insert the disk in the DVD-ROM/CD-ROM drive and locate the PATH.DOC file in the root directory. -
Page 57: Intel ® Matrix Storage Manager Raid Configurations
Chapter 5 Intel Matrix Storage Manager RAID Configurations ® ® The Intel Matrix Storage Manager allows you to configure RAID 0, and 1 sets on the external Serial ATA hard disk drives. Before creating a RAID set Prepare the following items: One SATA HDD. -
Page 58: Entering Intel Matrix Storage Manager Raid Bios Util- Ity
® Entering Intel Matrix Storage Manager RAID BIOS util- ® During POST, press <Ctrl-I> to enter the Intel Matrix Storage Manager RAID BIOS menu. ® The main Intel Matrix Storage Manager RAID BIOS menu appears. Use the arrow keys to move the color bar and navigate through the items. Intel Matrix Storage Manager RAID Configurations ®... - Page 59 Creating a RAID set In the main Intel ® Matrix Storage Manager RAID BIOS menu, highlight Create RAID Volume using the up/down arrow key then press <Enter>. When the RAID Level item is highlighted, use the up/down arrow key to select the RAID set that you want to create.
-
Page 60: Creating A Raid Set
When done, press <Enter> to confirm the creation of the RAID set. A dialogue box appears to confirm the action. Press <Y> to confirm; other- wise, press <N>. Pressing <Y> deletes all the data in the HDDs. The following screen appears, displaying the relevant information about the RAID set you created. -
Page 61: Deleting A Raid Set
Deleting a RAID set In the main Intel ® Matrix Storage Manager RAID BIOS menu, highlight Delete RAID Volume using the up/down arrow key then press <Enter>. Use the space bar to select the RAID set you want to delete. Press the <Del>... -
Page 62: Resetting Disks To Non-Raid
Resetting disks to Non-RAID An HDD that has been previously configured as part of another RAID set in another platform is called a broken RAID HDD. When you install a broken RAID HDD, you cannot select this disk when configuring a RAID ®... -
Page 63: Setting Up Ejiffy
Note: eJIFFY is ECS optional feature utility corresponding to the DVD activation and BIOS setup. Please check the hard copy user’s guide or product color-box to see if the model has embodded eJIFFY feature. -
Page 64: Installation And Bios Setup
DVD Activation Finish the DVD utility setup, and then set the BIOS to complete eJIFFY activation. 1. Insert ECS software utility DVD and enter below “Utilities” screen. Click eJIFFY feature item to install. 2. Follow the onscreen instructions to finish eJIFFY setup. - Page 65 3. After setting up eJIFFY under Windows, you can switch eJIFFY display/keyboard language from English to your local language. The changes will be applied after rebooting. Note: The keyboard language selection list offers several more regional keyboard setups to switch with the default English typing. Please refer to the usage FAQ for more tips.
- Page 66 Setup button on the post screen to enter the BIOS setup page after boot up. 5. And then enter the Advanced Setup page to enable the item ECS eJIFFY Func- tion. Press F10 to save the configuration and exit. Restart your computer.
-
Page 67: Entering Ejiffy
Entering eJIFFY The post screen appears within several seconds after boot up and it has three buttons on it, Operating system, eJIFFY and BIOS Setup. Click to enter the normal OS you have installed such as Windows. Click to enter eJIFFY OS. Click to set the BIOS. -
Page 68: Features Icons
Feature Icons The following illustration shows the main feature icons that eJIFFY provides on the menu. eWeb: Firefox for web browsing/webmail and watching flash video. ePix: Photo viewing. ePal: On-line chat tool to use the most popular IMs in the world. (MSN, ICQ , AIM, etc.) Shows ePal on-line connection status. -
Page 69: Usage Faq
Usage FAQ Language Control Panel: Besides setting English as the default interface, eJIFFY offers multi-language displays and keyboard settings for language- switch. Open the language control panel to select a preferable language setting. Keyboard Language Setup to open the language control panel. Step1. - Page 70 Step 2: Click “Keyboard Language” icon to open the keyboard selection list, which offers several regional keyboard settings besides default English keyboard. Step 3: Click the selected keyboard language (e.g. French) and press “OK”. Setting Up eJIFFY...
- Page 71 Tips for Language Switch: Tip 1: Click “Change Keyboard” icon to switch the typing language. The typing language on text box will switch to the selected one: Click again to switch to English typing back. Tip 2. If you use the default English keyboard, eJIFFY still offers other language inputs to switch with English.
- Page 72 Setting Up eJIFFY...
- Page 73 Setting Up eJIFFY...
- Page 74 Tip 3. How to change display language? Open the Language Control Panel and click to show the display language list. Check your desired display language. Your selected display language will be applied after rebooting. Setting Up eJIFFY...
- Page 75 eWeb: Firefox for web browsing/webmail and watching flash video. Q1: How to download files to hard disk through eWeb? Click on the file link directly. Then select “Save File” in the pop-up window. 1. Before downloading files, please “mount” the storage devices to make Note: sure the device is connected with eJIFFY interface.
- Page 76 Q2: How to save image file through eWeb? 1. Select the image you want to save and press the right key of your mouse to show the menu, then click the option “ Save Image As” from the menu. 2. Then the “Save Image” window appears. You may rename the image file in the “Name”...
- Page 77 ePix: Photo viewing. Q1: How to find image files saved in hard disk through ePix? Enter the ePix window, then click the icon “Folder” located in the upper left-hand corner, then follow the path for the files you have saved to view the image files. Setting Up eJIFFY...
- Page 78 Q2: How to use the fit function under slide show? 1. Click “Edit” and select “Preferences” option from the menu. 2. Click “Viewer” and choose “Keep previous zoom” in “After loading an im- age”. Close the window and you can use the fit function under slide show now. Note: ePix supports to view image files only.
- Page 79 Mount/Unmount Disk. Q1: What does it mean for “Mount Disk”? “Mount” means to connect the storage devices to eJIFFY interface. After plugging the external device to the computer such as USB drives, a new disk icon will appear as the following picture shows. Please click the “mount” prompt on the icon.
- Page 80 Memo Setting Up eJIFFY...
-
Page 81: Trouble Shooting
Chapter 7 Trouble Shooting Start up problems during assembly After assembling the PC for the first time you may experience some start up problems. Before calling for technical support or returning for warranty, this chapter may help to address some of the common questions using some basic troubleshooting tips. -
Page 82: Start Up Problems After Prolong Use
c) The PC suddenly shuts down while booting up. 1. The CPU may experience overheating so it will shutdown to protect itself. Ensure the CPU fan is working properly. 2. From the BIOS setting, try to disable the Smartfan function to let the fan run at default speed. - Page 84 Memo Trouble Shooting...
Need help?
Do you have a question about the P55H-A2 and is the answer not in the manual?
Questions and answers