Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Euromaid WM7
Summary of Contents for Euromaid WM7
- Page 1 Washing Machine...
-
Page 2: Warnings General Safety
1 Warnings Safety instructions General Safety • This appliance must be connected to an earthed outlet protected by a fuse of • Never place your machine on a carpet suitable capacity. covered floor. Otherwise, lack of airflow • The supply and draining hoses must from below of your machine may cause always be securely fastened and remain in electrical parts to overheat. This may cause an undamaged state. problems with your washing machine. • Fit the draining hose to a washbasin or • If the power cable or mains plug is bathtub securely before starting up your damaged you must call Authorized Service machine. There may be a risk of being for repair. scalded due to high washing temperatures! • Fit the drain hose into the discharge • Never open the loading door or remove the housing securely to prevent any water filter while there is still water in the drum. leakage and to allow machine to take in • Unplug the machine when it is not in use. and discharge water as required. It is very • Never wash down the appliance with a important that the water intake and drain water hose! There is the risk of electric hoses are not folded, squeezed, or broken... -
Page 3: Installation Removing Packaging Reinforcement
2 Installation Removing packaging reinforcement Tilt the machine to remove the packaging reinforcement. Remove the packaging reinforcement by pulling the ribbon. • If you are going to use your double water- Opening the transportation locks inlet machine as a single (cold) water-inlet Transportation safety bolts must be unit, you must install the stopper*, supplied removed before operating the washing with your machine to the hot water valve. machine! Otherwise, the machine will be • If you want to use both water inlets of the damaged! product, you can connect the hot water 1. Loosen all the bolts with a spanner until hose after removing the stopper and they rotate freely (“C”) gasket group from the hot water valve. -
Page 4: Electrical Connection
Electrical connection Detergents and softeners Connect the machine to an earthed outlet Detergent Drawer protected by a fuse of suitable capacity. The detergent dra wer is composed of three compartments: Important: • Connection should comply with national The detergent dispenser may be in two regulations. -
Page 5: Control Panel
4 Selecting a Program and Operating Your Machine Control panel Figure 1 1 - Spin Speed Adjustment Button 5 - Auxiliary Function Keys 2 - Time Delaying Button (+/-) 6 - Program Selection Knob 3 - Temperature Adjustment Button 7 - Display 4 - Start/Pause/Cancel Button 8 - On/Off Button Display symbols... -
Page 6: Additional Programs
• Cotton • Xpress Super Short You can wash normally soiled durable cotton You can use this program to quickly wash a clothes with this program. Your laundry will be small number of lightly soiled and unstained washed with vigorous washing movements cotton garments. -
Page 7: Program Selection And Consumption Table
rinse hold and no spin options are shown spin your laundry after the rinse hold function: respectively. Adjust the spin speed. Rinse hold is shown with “ ” and no spin is Press “Start/Pause/Cancel” button. shown with “ ” symbols. Program resumes. -
Page 8: Auxiliary Functions
and amount of laundry, auxiliary functions Auxiliary functions selected, and changes in the supply voltage. Auxiliary Function Selection Buttons Select the required auxiliary functions Time delay before starting the program. With the “Time delay” function you can delay Some combinations cannot be selected the program start up to 24 hours. Setting can together. (Ex.: Pre-wash) (Figure 1-5a) and be made in intervals of 30 minutes. -
Page 9: Childproof Lock
5 Maintenance and cleaning Switching the machine to standby Detergent Drawer mode Remove any powder residue buildup in the drawer. To do this; Press “Start/Pause/Cancel” button momentarily to switch your machine to the 1. Press the dotted point on the siphon in the standby mode. Auxiliary functions can be softener compartment and pull towards cancelled or selected in accordance with you until the compartment is removed from... -
Page 10: Draining Remaining Water/Cleaning Pump Filter
Draining any remaining water and by pulling out the plug at the end of the hose. If the amount of water to be drained cleaning the pump filter off is greater than the volume of the Your product is equipped with a filter system container, replace the plug, pour the water which ensures a cleaner water discharge that out, then resume the draining process. extends pump life by preventing solid items • After draining process is completed, such as buttons, coins and fabric fibers from replace the plug into the end of the hose clogging the pump propeller during discharge and fit the hose back into its place. -
Page 11: Troubleshooting
8 Solution suggestions for problems Cause Explanation / Suggestion Programme cannot be started or selected. Machine may have switched to self protection Bring your machine to factory settings by turning mode due to an infrastructure problem (such as the Programme selection knob. (see, Ending the line voltage, water pressure, etc.). Programme through Cancelling) Water in the machine. There may be some water in your machine when you receive it. This is from the quality It is not harmful to your machine. control process and is normal. There is water coming from the bottom of the machine. - Make sure that the seals of the water inlet hoses are There might be problems with hoses or the securely fitted. pump filter. - Tightly attach the drain hose to the tap. - Make sure that the pump filter is completely closed. Machine does not fill with water - Tap may be turned off. - Open the inlet water taps fully. - Water inlet hose might be bent. - Flatten the water intake hose. - Water inlet filter might be clogged. - Clean the water intake filter. - The loading door may be ajar. - Close the loading door. Machine does not discharge water. - Water outlet hose might be clogged or - Clean or flatten the hose. twisted. - Page 12 Machine fills with water when a process is cancelled. For safety reasons cold water is added to cool the hot Inside of machine may be hot. wash load It continuously spins. Remaining time does not count down. (On models with display) - The automatic spin correction system might have been activated due to the unbalanced distribution of the laundry in the drum. - The laundry in the drum may be clustered (bundled There may be an imbalance of laundry in the laundry in a bag). Laundry should be rearranged and machine. re-spun. - No spinning is performed when the laundry is not evenly distributed in the drum to prevent any damage to the machine and to its environment. Washing time takes longer than the time specified in the manual - The machine will wait until there is sufficient amount of water, which will lengthen the washing time to avoid poor washing results due to insufficient water. - Washing time is extended to avoid poor washing results when the supply voltage is low. - Cycle time is extended to heat up the water when - Water pressure may be low. the input water is cold. Also, washing time can be - Supply voltage may be low. lengthened to avoid poor washing results. - Input temperature of water may be low. - The automatic spin correction system might have - There may be an imbalance of laundry in the been activated due to the unbalanced distribution of machine. the laundry in the drum. - Number of rinses and/or amount of rinse - The laundry in the drum may be clustered (bundled water might have increased. laundry in a bag). - Laundry should be rearranged and re-spun. - No spinning is performed when the laundry is not evenly distributed in the drum to prevent any damage to the machine and to its environment.
- Page 13 Washing performance is poor: Laundry turns grey - Use the recommended amount of detergent - Using insufficient amount of detergent for a appropriate for water hardness and the laundry. long time, - Select the proper temperature for the laundry to be - Washing at low temperatures for a long time, washed. - Using insufficient amount of detergent for - If the water hardness is high, using an insufficient hard waters (soil can stick to the laundry), amount of detergent can cause laundry to turn grey - Using excessive amount of detergent over time. (detergent can stick to the laundry). - It is difficult to eliminate such greyness once it occurs. Washing performance is poor: Stain could not be removed, not cleaned. Laundry could not be whitened. - Use recommended amount of detergent appropriate - Insufficient amount of detergent used. for the laundry. - Excessive laundry loaded into machine - Do not load the machine in excess. - Wrong Programme and temperature might - Select the proper Programme and temperature for have been selected. the laundry to be washed. - Improper detergent may have been used. - Put the detergent in the correct compartment. - Wrong type of detergent used. - Do not mix detergent with bleaching agents. - Washing performance is poor: Oily stains appear on laundry. - Washing performance is poor: Bad odour - Such odours and bacteria layers are formed on the drum as a result of continuous washing at lower temperatures and/or in short Programmes. - Oily accumulations on the drum may have - Leave the detergent dispenser drawer as well as the stuck to the laundry. loading door of the machine ajar after each washing.
- Page 14 Clothes stiffened. - If the water hardness is higher, using insufficient amount of detergent can cause the laundry to become stiff in time. Use appropriate amount of detergent - Insufficient amount of detergent used. according to the water hardness. - The detergent may have been placed into the - If detergent is put in the prewash compartment wrong compartment; the detergent may be although prewash cycle is not selected, machine can mixed with the softener. take this detergent during rinsing or softener step. - Do not mix the softener with detergent when putting in the compartment. - Wash and clean the drawer with hot water. Clothes do not smell like the softener. - If the water hardness is higher, using insufficient amount of detergent can cause the laundry to become stiff in time. Use appropriate amount of detergent - Insufficient amount of detergent used. according to the water hardness. - The detergent was placed into the wrong - If detergent is put in the prewash compartment compartment; the detergent was mixed with although prewash cycle is not selected, machine can the softener. take this detergent during rinsing or softener step. Do not mix the softener with detergent when putting in the compartment. Wash and clean the drawer with hot water. Detergent residue in the dispensing drawer. - Detergent may have been put in wet - Dry the detergent drawer before putting in detergent. dispenser drawer. - Store detergent in a closed and dry location. - Detergent may have gotten damp. - Do not keep them under high temperatures. - Water pressure might be low - The detergent dispenser outlet (holes) may have a - The detergent in the main wash compartment problem.
-
Page 15: Specifications
7 Specifications Models Maximum dry laundry capacity (kg) Height (cm) Width (cm) Depth (cm) Net Weight (±4 kg) 220-240 V / 50Hz Electricity (V/Hz.) Total Current (A) 2000-2350 Total Power (W) 1200 Spinning cycle (rpm max.) Specifications of this appliance may change without notice to improve the quality of the product. Figures in this manual are schematic and may not match your product exactly. Values stated on the machine labels or in the documentation accompanying it are obtained in laboratory in accordance with the relevant standards. -
Page 16: Handy Tips
EUROMAID FRONT LOAD WASHER HANDY TIPS WASHING POWDER MUST BE FRONT LOAD TYPE ONLY! PLEASE USE NO MORE THAN ONE SCOOP PER LOAD. WE RECOMMEND POWDER DETERGENT RATHER THAN LIQUID IF YOU ARE USING PRODUCTS SUCH AS NAPPYSAN ETC REMEMBER THIS IS A WASHING POWDER THEREFORE WASHING POWDER IS NOT NEEDED. - Page 17 17 - EN...
- Page 18 18 - EN...
- Page 19 EMAIL: s ales@euromaid.com.au W EBSITE: ...
- Page 20 FOR O UTSIDE S ERVICE A REAS P LEASE C ONTACT O UR S ERVICE & C ARE C ENTRE A T N EWCASTLE 02 ...
Need help?
Do you have a question about the WM7 and is the answer not in the manual?
Questions and answers
Can I turn off heating
The Euromaid WM7 allows temperature adjustment using the Temperature Adjustment Button. However, the documents do not specify if you can completely turn off the heating.
This answer is automatically generated
After cleaning the filter and replacing cap , water is still leaking out from it
Water may be leaking from the filter cap on the Euromaid WM7 after cleaning because the filter was not fully fitted into its housing. If the filter is not properly placed, water can escape from the filter cap. Ensure that the filter is completely inserted without forcing it and that the cap is securely closed.
This answer is automatically generated
WM7 washing machine - front loader Drum filling with water even when machine is off, any advise on troubleshooting steps?