Alinco DR-150 T Instruction Manual

Vhf/fm mobile transceiver

Hide thumbs Also See for DR-150 T:

Service manual (45 pages)

Modification (1 page)

Accessories manual (1 page)

Table Of Contents

Table of Contents

Table of Contents
Notice
Before Operating the Transceiver
Standard and Optional Accessories
Mobile Antenna Installation
Location
Power Requirements
Base Station Installation
Specifications
Panel Description
Front Panel
Primary Functions
Secondary Functions after F Is Pushed for Less than 0.5 Sec (Func Appears)
Functions after Pushing the F Key for more than 0.5 Sec (Func Appears and Flashes)
Functions Pressed While Turning Power on
Display
Rear Panel
Microphone
Microphone Pin Assignments
Basic Operation
Receiving
Adjusting the Audio Volume
Adjusting the Squelch
Receive Frequency Range (Mhz)
Selecting a Frequency
Changing the Mhz Digit Only
Transmitting
Transmit Frequency Range (Mhz)
Selecting a Frequency for Transmit
Selecting an Output Power
Operating Modes
VFO Mode
Memory Mode
Call Mode
Main and Sub Band Operation
Changing Bands
Advanced Functions
Memory Channels
Memory Types and Default Settings from the Factory
Calling up a Memory Channel
Temporarily Changing a Memory Channel Frequency (Temporary Mode)
Programming a Memory Channel
Clearing a Memory/Reclaiming a Memory
Transferring a Memory to VFO
Operating in Memory Channel Indication Mode (Channelized Mode)
Call Channel
Calling up the Call Channel (Call Mode)
Changing the Call Channel's Frequency
Channel Scope
VFO Channel Scope
What Do the VFO Scope Level Indications Mean?
Changing the Center Frequency
Memory Channel Scope
What Do the Memory Scope Level Indications Mean?
Changing the Center Channel
Channel Scope Operation with the DTMF Equipped Microphone (EMS-12)
Starting and Stopping the Scope Function
Changing the Center Channel Receive Period (5 Sec./O Sec.)
Receiving in Single Start Mode
Scanning
Setting a Scan Type
Band Scan
Programmed Scan
Programming the Scan Range into Memory
Programmed Scan from VFO Mode
Programmed Scan from Memory Mode
Memory Scan
Setting Non-Scan (Skip) Channels
Operation During Scanning
Band Sweep Scan
What Do the Sweep Scan Levels Mean?
Programmed Sweep Scan
Memory Sweep Scan
Priority Watch on 2 Channels
Other Functions
S-Meter Squelch Function
Setting a Squelch Level During Normal Receive
Setting a Squelch Level During the Channel Scope Operation
Setting the Squelch Timer
Shift and Split Settings (Using Different Frequencies for Transmit and Receive)
Reverse (Transmit and Receive Frequencies Are Exchanged)
Setting the Tone Encoder
Changing Tuning Steps
Key Lock Function
Bell Function On/Off
Adjusting the Display Brightness
Beep Tones On/Off
Setting the Transmit Time-Out Timer
RF Attenuator On/Off
Sending a Tone Burst Signal
Changing the Call/Tone Key Function
Receive LITZ Signal
AM Receive
Cloning
Receiving Side (Slave) Error
Resetting the CPU
Full Reset (All Settings Are Returned to Their Initial Values)
VFO Reset (VFO a and B Settings Only Are Returned to Their Initial Values)
Factory Default Conditions
Selective Calling
Tone Squelch (CTCSS)
DTMF Squelch (DSQ)
There Are Three DSQ Modes
Setting a Tone Squelch Frequency
Tone Scan
Setting DSQ Mode
Programming DSQ Codes
Off (Monitor Off)
Setting DSQ Mode with a DTMF Microphone (EMS-12)
Programming DSQ Codes Using DTMF Microphone (EMS-12)
Communicating in Code Squelch Mode (DSQ)
Notes for DSQ Operation
Communicating in Group Pager Mode (G DSQ)
Preparation
Communicating in Private Pager Mode (P DSQ)
Changing the Rate of Transmission of DTMF Codes
Adjusting the DTMF Code Burst Time
Transmitting DTMF Codes Manually
Auto-Dialing
Programming Transmit Codes into Memory
Programming a Pause
Correcting a Code that You Have Entered
Clearing a Code
Confirming a Received DTMF Code
Transmitting a Specific Memory
Transmitting Dial Memory M1
Inhibiting Auto-Dialing (Clearing Dial)
Microphone Remote Control Commands
Operating Procedure for Microphone Remote Control
Explanation of Commands
Entering a Frequency Directly
DTMF Microphone (EMS-12)
Packet Operation
Requirements for Packet Operation
TXD (Transmit Data) Input Sensitivity
1200 Bps Packet Operation
Connecting Equipment for Packet Operation
9600 Bps Packet Operation
Connections for Packet Operation
Maintenance
Troubleshooting

Quick Links

1 Specifications
Download this manual

Need help?

Do you have a question about the DR-150 T and is the answer not in the manual?

Questions and answers

This manual is also suitable for:

Dr-150 e

Alinco DR-150 T Instruction Manual

Quick Links

Need help?

Questions and answers

Related Manuals for Alinco DR-150 T

Related Products for Alinco DR-150 T

This manual is also suitable for:

Table of Contents