HP P5389A - Intel Pentium III-S 1.4 GHz Processor Upgrade Reference

HP Server tc3100 Technical Reference Label
A
Chassis/Front LEDs
System
Power
Fan
Supply
System
Board
Diag.Board
(optional)
*
Included in certain models
B
Mass Storage Device Locations and Settings
Device
Standard FDD
HP Accessory 18.2 GB HDD or
HP Accessory 36.4 GB HDD or
HP Accessory 72 GB HDD
HP SureStore DAT 24i
Standard SCSI Controller
Standard CD-ROM
See documentation with each device for further configuration information.
C
System Board
Caution:
Do not mix CPU types or speeds. Both
CPUs must be the same type and speed.
Terminator is required in secondary CPU
slot when second CPU is not installed.
DIMM Installation
Use only PC 133 buffered ECC, SDRAM DIMMs.
Any combination (mix or match) of up to four
each of 128MB, 256MB, 512MB, or 1GB DIMMs.
Order of installation is slot 3, 2, 1, 0 with largest
DIMMs installed in the highest slot number.
Default Boot Order
1. IDE CD-ROM
2. FDD
3. Embedded SCSI A
4. Embedded SCSI B
5. PCI 6
6. PCI 5
HP Server tc3100 Technical Reference Label
E
Mass Storage Cabling/Rear LEDs
System Board
SCSI A
Optional External Cable
FDD
F
Tips for Removing
the System Board
Unplug power. Open side
panel.
Lay unit on side.
Disconnect all cables from
system board.
Take out CPUs. If only one
CPU is present, also
remove terminator from
second slot.
Take out all PCI cards.
Remove all 8 screws
(see illustration).
Grasp and unsnap the 2
snaps at the righthand
corners of system board.
Slide board forward, lift
out carefully.
Screw Screw Screw
Screw Screw
Shelf 8:
Flexible Disk
Shelf 7:
CD-ROM
Shelf 6:
Optional Tape
*
Drive
Cold-Swap
Shelves
5, 4, 3, 2, 1
Hot-Swap
Slots
5, 4, 3, 2, 1
Device Settings
Location in order of
recommendation
Shelf 8
For Cold- and Hot-Swap models:
Shelf 1, 2, 3, 4, 5 or
No settings are required. Set by
Slot 1, 2, 3, 4, 5
the backplane.
Shelf 6 SCSI ID 2 [Default]
Embedded SCSI ID 7
Shelf 7 Set to Cable Select (CS)
LAN USBs
7. PCI 4
8. PCI 3
9. PCI 2
10. PCI 1
11. Embedded LAN
A
Shelf 8
B
Shelf 7
Shelf 6
Terminator
Backplane
C
SCSI B
Terminator
IDE-2
D
G
Power Cabling
Cold-Swap Model
Power Supply
Unit
24-pin Power
Connector
System
Board
H
Diagnostic Board
Snap
Cabling
See Panel I for further
information.
Screw
ERMC
50-pin Cable
PCI Slot 6
Snap
Front LED Indicators
System Power Indicator
Off -- System is Off
Solid green -- System is running
Blinking green -- System in sleep
mode
Disk Activity Indicator
Blinking amber -- SCSI activity
LAN Activity Indicator
Blinking green -- LAN activity
Processor 1(CPU 1)
System Fan
Mouse &
Keyboard
Power
Connector
Serial A
Parallel Port
Serial B
Video SVGA
Processor 2
(CPU 2)
Wake-On-LAN
ERMC
FDD (FDD)
CD-ROM (IDE-2)
Optional Tape Drive
(SCSI A)
Shelf 5
Shelf 4
Shelf 3 Cold-Swap
Drives (SCSI B)
Shelf 2
Shelf 1
SCSI B connects Cold-Swap cage
with 5 connectors or Hot-Swap cage
with one connector.
Slot 5
Slot 4
Hot-Swap
Slot 3
Drives (SCSI B)
Slot 2
Slot 1
Shelf 8
P1
Shelf 7
P2
Shelf 6
P3
Shelf 5
P4
Shelf 4
P5
P6 Shelf 3
Shelf 2
P7
Shelf 1
Diagnostic
Board
Connector
P/N P3505-80202
Audience Assumptions
This Technical Reference Label is for trained service
personnel. Hewlett-Packard Company assumes you
are qualified in the servicing of computer equipment
and trained in recognizing hazards in products with
hazardous energy levels.
Electrostatic Discharge
To avoid catastrophic or hidden damage to
components, wear a wrist strap and use a static-
dissipative work surface connected to the chassis
when handling components. Use an antistatic
service kit, such as 3M 8501/8502/8505 or
®
equivalent.
This information is subject to change without notice
and is provided without warranty.
© Copyright 2002 Hewlett-Packard Company
D

Service Information

Electronic Support Services
Internet Web Pages
http://www.hp.com/
Internet FTP
ftp://ftp.netserver.hp.com
HP Navigator CD
Support Questions
HP-Authorized Reseller
US/Canada Phone Support
Europe Phone Support
(+31-20) 581-3330 (Netherlands)
HP has offices in over 100 countries.
Check your local telephone directory.
Optional HP 3 Year On-Site Support Pack
H4634A/E/VV
SDOS, 4 hour response
H4636A/E/VV 24 x 7, 4 hour response
H5544A/E/VV 6 hours Call-to-Repair
DIMM Slots
CPU 1 Fan
0 1 2 3
IPMI FDD Diag. Board
Connector
Cables
Flexible
A
Disk Cable
B
CD-ROM Cable
C
Cold-Swap SCSI
D
Hot-Swap SCSI
Rear LED Indicator (on LAN Connector)
Activity Link Indicator
Steady Green-- Link Valid
LED LED
Blinking Green --
Activity on LAN
Hot-Swap Model
Power Supply
P1
Unit
P2
P3
No connect
24-pin Power
Connector
P5
P6
P7
System
IPMI
Board
I
Diagnostic Board
When any LED is illuminated, a condition exists that
requires the attention of a service technician.
= OK See Tech Reference Label
1 2
PROCESSOR Processor
MEMORY DIMM 0
MEMORY DIMM 1
Memory
MEMORY DIMM 2
MEMORY DIMM 3
SYSTEM FAN
System Fan
1
= OK See Tech Reference Label
System Board
SYSTEM BOARD
Memory Config.
MEMORY CONFIG
PROCESSOR CONFIG Processor Config.
System Temperature
SYSTEM TEMPERATURE
Event Log
CHECK EVENT LOGS
1-208-331-2767
CPU 2 Fan
Battery
SCSI A
SCSI B
Config.
Switch
IDE 2
Status
Panel
Part Number
P3505-63014
P3505-63017
P3505-63013
P3505-63018
LAN Speed Indicator
OFF-10Mbps
Steady Yellow-100Mbps
Shelf 8
Shelf 7
Shelf 6
Slot 5
Slot 4
Slot 3
Slot 2
Slot 1