Related Manuals for D-Link DFE-2624 - Hub - Stackable
Summary of Contents for D-Link DFE-2624 - Hub - Stackable
- Page 1 DFE-2600 Series Web-based Management User’s Guide Rev. 02 (August, 1998) 6DFE2600..02 Printed In Taiwan RECYCLABLE...
-
Page 2: Table Of Contents
ABLE OF ONTENTS ......1 BASED ETWORK ANAGEMENT Introduction........................1 getting started....................... 1 Management ......................... 2 Configuration ..........................2 Control............................7 Performance ..........................12... -
Page 3: Web - Based Network Management
BASED ETWORK ANAGEMENT Introduction The content of this user’s guide pertains to intelligent (management) Hub models only. An embedded web-based (hypertext) interface allows users to manage the switch from anywhere on the network through a standard browser such as Netscape Navigator/Communicator or Microsoft Internet Explorer. -
Page 4: Management
Dual-Speed Stackable Hub Web-based Management User’s Guide The second and last step is to configure the IP interface, of the Hub, through console management. See the In-Band Setup Instructions on page 39 to do this. Management Your Hub has a hypertext interface, allowing you to do management through your browser. - Page 5 The Hub information is described as follows: System Description A description of the hub type. System OID The SNMP Object Identifier for this hub type. System Uptime The amount of time that the hub stack has been powered on. System Contact User-defined information for the physical location of the hub. System Name A user-assigned name for the hub.
-
Page 6: Trap Receivers
Dual-Speed Stackable Hub Web-based Management User’s Guide The information is described as follows: IP Address The Internet address for the device. Subnet Mask The subnet mask determines the level of the subnet that the hub is Default Gateway The default router for the device. MAC Address The physical address for the device. -
Page 7: Software Download
Community This is the SNMP community name to authenticate the receiving of traps. Delete This will remove a trap receiver from the trap receiving table. Software Download The Software Download screen allows you to cause an immediate update of the hub’s parameters and/ or firmware. -
Page 8: Snmp Manager Configuration
Dual-Speed Stackable Hub Web-based Management User’s Guide Boot Server Address The IP address of the TFTP server where the configuration file is located. tftp only bootp-tftp Boot Protocol Set to either . Applies only if the Software Update Control is enabled. Get IP From Bootp Server If enabled, the address will be obtained from the BOOTP server. -
Page 9: Control
Control The operations described in this section allow you to manage the Hub while it is operating. Group/ Port and Console Control Group/Port Configuration Fault Group/Port Control to Click show the Control screen. Hub (group), port, and console configurations can be easily selected from this screen. - Page 10 Dual-Speed Stackable Hub Web-based Management User’s Guide The information is described as follows: Current Serial Port Setting Displays the current session, either Console or Out-of-band . System Restart Serial Port Setting You can choose to select Console or Out-of-band management upon reboot. Baud Rate This is cps (characters per second) of the information exchange between the Hub and it’s console manager.
- Page 11 Group (Hub) Configuration Clicking Fault Group/Port Control [Hub ID] will show the current configuration information of the Hub. The information is described as follows: Serial Number This is a unique hardware serial number of the Hub. Description This is the product ID. Slot 1/ Slot 2 Type These indicate the type of module, if present, in the back-slot of the Hub.
-
Page 12: Port Configuration
Dual-Speed Stackable Hub Web-based Management User’s Guide Isolated/ Reconnected Group This is an option to isolate or reconnect the Hub in the hub stack. Port Configuration Clicking Fault Group/Port Control [Port ID] will show the current configuration information of the port. The information is described as follows: Port Type The type is UTP, BNC, or AUI. - Page 13 Link Test Function State Indicates the whether the port link-test is enabled or disabled . If enabled, the port will check for link pulses, and will only transmit if there is a good link to another station. Administration State Indicates the port’s partition status, either enabled or disabled .
-
Page 14: Performance
Dual-Speed Stackable Hub Web-based Management User’s Guide Performance Hub performance is measured with packet statistics and it’s utilization in the network. Statistics The Hub allows you to collect network statistics of individual ports, 10Mbps segments or 100Mbps segments, and any Hub in the stack. Statistics collected by the Hub are described as follows: StatsPkts (Pkts) Counts valid frames. - Page 15 CRC AlignErrors (Pkts) Counts otherwise valid frames that did not end on a byte (octet) boundary. UndersizePkts (Pkts) Counts packets received that were less than 64 octets long (excluding framing bits, but including FCS octets) and were otherwise well formed. OversizePkts (Pkts) Counts packets received that were longer than 1518 octets (excluding framing bits, but including FCS octets) and were otherwise well formed.
-
Page 16: User List
Dual-Speed Stackable Hub Web-based Management User’s Guide Utilization is calculated and plotted every 10 seconds. At any time, at most, a one hour utilization history can be shown by the graph. User List The User List display, displays the Ethernet (MAC) addresses of packets recently received by the hub stack. - Page 17 Time Shows the amount of time since the last packet was transmitted on the port. Intrusion The Hub’s intrusion security feature can be used to dedicate a port to a given piece of hardware. If a different device transmits to the port, the hub can be set to either partition the port, send a trap notification to the network manager, or both.
- Page 18 Dual-Speed Stackable Hub Web-based Management User’s Guide Action The action to be taken in event of intrusion on the port: send trap , partition , send trap & partition , or no action . Auto Learn Can set auto-learning to enable or disable . Delete Click this to delete and disable a port/ intrusion entry.