Panel Programming - ITI 60-804-04 - Concord LCD/VFD Alphanumeric SuperBus Keypad Installation Instructions Manual

2x20 vfd aplhanumeric touchpad

Hide thumbs

Table Of Contents

Table of Contents

Deleting Touchpads/Unit Numbers from Panel Memory

At a touchpad, press and hold the D and 6 buttons

(together) for at least 2 seconds. The display should

show DA n, where n is the current unit number (000 –

015) for the touchpad.

Note

At this time, the touchpad is in configuration mode and

no longer communicating with the panel. The system

may immediately indicate a bus failure. Ignore the fail-

ure and continue with the procedure. The failure will

clear after the unit number has been successfully

changed.

Press ƒ. The display shows ENTER _.

Enter an unused three digit unit number (000 – 015),

then press ƒ. The display shows DA n, where n is the

new unit number for the touchpad.

Press ‚ to exit from the configuration mode.

Repeat steps 4–8 for all connected alphanumeric

touchpads.

Note

If the new unit number for the touchpad was previ-

ously added (learned) by the panel, communication

between the touchpad and the panel begins immedi-

ately. However, if the new unit number for the touch-

pad has never been added (learned) by the panel,

continue with step nine.

Force the panel to scan bus devices.

For systems where this is the only installed touch-

pad, remove the panel AC power and backup bat-

tery power, then re-apply power.

For systems with more than one touchpad, go to

another system touchpad and enter 8 + installer

CODE (default = 4321) + 0 + 1. The display

shows SCANNING BUS DEVICES, then a date

and time display.

10. Exit the program mode. The touchpad and all other bus

devices should operate correctly and any bus failures

should be cleared.

Note

If the panel still indicates a bus failure the panel may

have previously learned a unit number that is no

longer used by any bus device. Delete the unused unit

number.

11. Verify correct operation by pressing ‚. The display

should show the current system status.

Note

‚

If after pressing

the touchpad does not display the

current system status, see "Troubleshooting."

Powering Up Advent Panels

New Installations

Verify that all wiring between the panel and touchpad is

correct.

Connect the panel battery and plug in the panel trans-

former. The alphanumeric touchpad should display

"Security is Off," or any other programmed text.

Note

If the touchpad does not display anything or displays,

"Touchpad Not Enrolled," see "Troubleshooting."

Existing Installations

Verify that all wiring between the panel and touchpad is

correct.

Connect the panel battery and plug in the panel trans-

former.

At an existing touchpad, press 8 to select SYSTEM

MENU.

Press 0 to select ENTER PROGRAM MODE.

Enter your install access CODE (0123 is default).

Enter item number 48001 to add bus devices. All

installed devices are automatically added (learned) into

panel memory when DEVICES ADDED is displayed.

Press ‚ once to exit program mode.

New alphanumeric touchpads should display "Security

is Off," while existing touchpads will display custom or

programmed text.

Note

If the touchpad does not display anything or displays,

"Touchpad Not Enrolled," see "Troubleshooting."

Deleting Touchpads/Unit Numbers

from Panel Memory

Please see the specific Installation Instructions for informa-

tion on deleting touchpads/unit numbers.

Adjusting Touchpad Brightness

Please see the specific panel Installation Instructions or

User's Manual for more information.

Testing

CAUTION

Contact the central monitoring station before activating

alarms to avoid dispatching local police and fire

departments.

Test the touchpad by arming and disarming the system, acti-

vating the touchpad panics, bypassing sensors, and by turn-

ing lights on and off to verify the correct operation. Refer to

the panel Owner's Manual for system operating instruc-

tions.