Download
Share
Print this page
Denon DRA-697CI - AV Receiver Manual
  1. Manuals
  2. Brands
  3. Denon Manuals
  4. Home Theater System
  5. DRA-697CI
  6. Manual
Denon DRA-697CI - AV Receiver Manual

Denon DRA-697CI - AV Receiver Manual

Avr/avc/dra control protocol
Hide thumbs Also See for DRA-697CI - AV Receiver:

Advertisement

Quick Links

Download this manual See also: Code List, Service Manual
DENON AVR/AVC/DRA control protocol
Application model : DRA-697CI
Application terminal : RS-232C
Connector specification
Connector type : DB-9pin female type, slave straight connection (DCE type)
( 1pin : GND , 2pin : TxD , 3pin : RxD , 5pin : Common(GND) , 4,6,7,8,9pin : NC )
Communication format :
Synchronous system
Communication system
Communication speed
Character length
Parity control
Start bit
Stop bit
Communication procedure
Communication data length
: Tone step synchronization
: A half duplex
: 9600bps
: 8 bits
: None
: 1 bit
: 1 bit
: Non procedural
: 135 bytes (maximum)
- 1 -
Ver. 4.9.0

Advertisement

loading
Need help?

Need help?

Do you have a question about the DRA-697CI - AV Receiver and is the answer not in the manual?

Questions and answers

Related Manuals for Denon DRA-697CI - AV Receiver

Summary of Contents for Denon DRA-697CI - AV Receiver

  • Page 1 DENON AVR/AVC/DRA control protocol Ver. 4.9.0 Application model : DRA-697CI Application terminal : RS-232C Connector specification Connector type : DB-9pin female type, slave straight connection (DCE type) ( 1pin : GND , 2pin : TxD , 3pin : RxD , 5pin : Common(GND) , 4,6,7,8,9pin : NC )
  • Page 2 Protocol specification The following three data forms is defined. COMMAND The message sent to a system(AVR/AVC/DRA) from a controller(Touch Panel etc.) A command to a system is given from a controller. EVENT The message sent to a controller(Touch Panel etc.) from a system(AVR/AVC/DRA) The result is sent, when a system is operated directly and a state changes.
  • Page 3 The example of a command * <CR> is the meaning of 0x0D. SIDVD<CR> : Select Input source DVD MVUP<CR> : Master Volume UP PWON<CR> : system PoWer ON PWSTANDBY<CR> : system PoWer STANDBY SI?<CR> : Request command for now playing input source >> Return RESPONSE ‘SI***<CR>’ - 3 -...
  • Page 4 Others A) COMMAND is receivable also during transmission of EVENT. B) Since CHANNEL VOLUME changes simultaneously when the SURROUND MODE changes, the value of the channel volume of all channels returns as EVENT. C) CHANNEL VOLUME returns the data of ALL channels by the present SURROUND MODE also including an intact channel. In this case, the data of an intact channel is set to "50".
  • Page 5 COMMAND and PARAMETER list COMMAND PARAMETER function example POWER ON/STANDBY change PWON<CR> STANDBY PWSTANDBY<CR> Request PW Status PW?<CR> MASTER VOLUME UP/DOWN , direct change to **dB MVUP<CR> DOWN MVDOWN<CR> **:00 to 99 by ASCII , 80=0dB, 99=---(MIN) MV80<CR> Request MV Status MV?<CR>...
  • Page 6 COMMAND PARAMETER function example MAIN-ZONE ON/OFF change ZMON<CR> ZMOFF<CR> Request ZM Status ZM?<CR> BAND TUNER BAND SELECT ZMBAND<CR> SEARCH TUNER SEARCH SELECT ZMSEARCH<CR> MUTI ZONE-2 ON/OFF change Z2ON<CR> Z2OFF<CR> Request Z2 Status Z2?<CR> MULTI ZONE-2 VOLUME UP/DOWN , direct change to **dB Z2UP<CR>...
  • Page 7 COMMAND PARAMETER function example MLUTI ZONE-3 ON/OFF change Z3ON<CR> Z3OFF<CR> Request Z3 Status Z3?<CR> MULTI ZONE-3 VOLUME UP/DOWN , direct change to **dB Z3UP<CR> DOWN Z3DOWN<CR> **:00 to 99 by ASCII , 80=0dB, 99=---(MIN) Z380<CR> PHONO MULTI ZONE-3 mode set , and select source Z3PHONO<CR>...

  • Page 8: Loudness On/Off

    EVENT PARAMETER function example TONE DEFEAT ON PARAMETER setting PSTONE DEFEAT ON<CR> TONE DEFEAT OFF TONE DEFEAT ON/OFF PSTONE DEFEAT OFF<CR> TONE DEFEAT? Request PSTONE DEFEAT Status PSTONE DEFEAT?<CR> BAS UP BASS UP/DOWN , direct change to **dB PSBAS UP<CR> BAS DOWN PSBAS DOWN<CR>...
  • Page 9 EVENT PARAMETER function example ---Band set to AM TMAM<CR> ---Band set to FM TMFM<CR> ---Band set to XM TMXM<CR> Request TM Status TM?<CR> AUTO ---Tuning mode set to AUTO mode TMAUOT<CR> MANUAL ---Tuning mode set to MANUAL mode TMMANUAL<CR> CH NAME ******** XM CH NAME change (Band XM Only) TMCH NAME 20 on 20<CR>...
  • Page 10 ※iPod Extended Control EVENT PARAMETER function example Cursor Up Control IP90<CR> Cursor Down Control IP91<CR> Cursor Left Control IP92<CR> Cursor Right Control IP93<CR> Enter Control IP94<CR> Play/Pause Control IP9A<CR> Pause Control IP9B<CR> Stop Control IP9C<CR> Skip Plus Control IP9D<CR> Skip Minus Control IP9E<CR>...
  • Page 11 ※Cursor/Enter/Setup EVENT PARAMETER function example “Cursor Up” Control SSCUP<CR> “Cursor Down” Control SSCDN<CR> “Cursor Left” Control SSCLT<CR> “Cursor Right” Control SSCRT<CR> “Enter” Control SSENT<CR> MEN ON “System Setup Menu ON” Control SSMEN ON<CR> MEN OFF “System Setup Menu OFF” Control SSMEN OFF<CR>...
  • Page 12 EVENT(or RESPONSE) and PARAMETER list EVENT PARAMETER Function example POWER ON/STANDBY change PWON<CR> STANDBY PWSTANDBY<CR> MASTER VOLUME change , **:00 to 99 by ASCII MV80<CR> 98 = +18dB(MAX) 80 = 0dB 00 = -80dB 99 = ---(MIN) FL ** CHANNEL VOLUME change , **:00,38 to 62 by ASCII CVFL 50<CR>...
  • Page 13 EVENT PARAMETER function example MAIN-ZONE ON/OFF change ZMON<CR> ZMOFF<CR> PHONO MULTI ZONE-2 source change Z2PHONO<CR> ---The name of PARAMETER is CDR/TAPE the same as that of the time of SI COMMAND. Z2CDR/TAPE<CR> SOURCE MULTI ZONE-2 mode cancel Z2SOURCE<CR> MULTI ZONE-2 VOLUME change , **:10 to 99 by ASCII Z280<CR>...
  • Page 14 EVENT PARAMETER function example TONE DEFEAT ON PARAMETER setting PSTONE DEFEAT ON<CR> TONE DEFEAT OFF TONE DEFEAT ON/OFF PSTONE DEFEAT OFF<CR> BAS ** BASS change, **:40 to 60 by ASCII, 50=0dB(-10dB～10dB) PSBAS 50<CR> TRE ** TREBLE change, **:40 to 60 by ASCII, 50=0dB(-10dB～10dB) PSTRE 50<CR> LOU ON PARAMETER setting PSLOU ON<CR>...
  • Page 15 EVENT PARAMETER function example ****** (6 digits) TUNER Frequency change TF105000<CR> --- ****.** kHz at AM band (1050.00kHz at AM) ****.** MHz at FM band XM*** (3 digits) --- *** CH at XM band (Band XM Only) TFXM001<CR> (XM001 CH at XM) **(PRESET No.) TUNER PRESET change to No.** TPA1<CR>...
  • Page 16 ※iPod Extended Control EVENT PARAMETER function FLD Information(iPOD) is Answered By the IPA Command. Display Line1 Information IPA0※*************_???<CR> Display Line2 Information IPA1※*************_???<CR> *:ASCII CODE Character(MAX95Byte) _:Null ?:Exclusion(The character after Null should be disregarded) ※:Cursor Information Data(1Byte) Bit1,2,3:Don't Care Bit4:CURSOR SELECT=1 Bit5,6,7,8:Don't Care ************_?????:96byte Fixed <example>...