Computer Setup; Password Security - HP Pro 3005 - Microtower PC Manual

POST Audible Codes
Beeps Meaning
1 short beep and 1 long beep Bad memory or
followed by a three second memory configura-
pause tion error.
2 short beeps and 1 long No graphics card
beep followed by a three installed or graphics
second pause card initialization
failed.
3 short beeps and 1 long CPU configuration
beep followed by a three error or invalid CPU
second pause detected before
graphics card initial-
ized.
1 short beep followed by a No optical drive
one second pause found.
2 short beeps followed by a No CD found.
three second pause
3 short beeps followed by a Flashing not ready
three second pause (missing utility or
BIOS image file,
etc.)
4 short beeps followed by a Flashing operation
three second pause has failed (checksum
error, corrupted
image, etc.)
5 short beeps followed by a BIOS recovery was
three second pause successful

Computer Setup

Basic system information regarding system information, setup, power management, hardware,
and passwords is maintained in the Setup Utility held in the system ROM. The Setup Utility is
accessed by pressing the F10 key when prompted (on screen) to do so during the boot sequence.
If the screen prompt opportunity is missed, a restart will be necessary...
Computer Setup Menu
Heading Option / Description
Main System Infor- Lists the following main system specifications:
mation •
•
•
•
•
•
•
•
•
•
•
•
Set Time and Allows you to set system time and date.
Date
SATA Port 1 For each allows you to:
SATA Port 2 •
SATA Port 3
SATA Port 4
•
SATA Con- Allows you to disable/enable the SATA Controller.
troller
PATA Master For each, if PATA is used, allows you to:
PATA Slave •
•
•
•
•
PATA Con- Allows you to disable/enable the PATA Controller.
troller
Onboard FDC Disable/enable the diskette drive controller.
Controller
Drive A Allows you to set to None or 1.4M, 3.5 in.
Halt On Allows you to set POST error behavior to: all errors, no
errors, all but keyboard.
POST Delay
Advanced AMD NX Allows you to disable/enable the processor's No Execute Fea-
Function ture.
Init Display Allows you to set primary display device to PCI slot, OnChip
First VGA, or PCIEx.
iGPU Frame Allows you to specify the onboard VGA shared memory size
Buffer Size to Auto, 64MB, 128MB, 256MB.
Onboard HD Allows you to disable/enable onboard HD audio.
Audio
OnChip USB Disables/enables the universal host controller interface for
Controller USB (Universal Serial Bus).
USB Legacy Disable/enable (USB keyboard, mouse, and flash media).
Support
HP Pro 3005/3085 Illustrated Parts & Service Map, MT chassis 600835-001
Recommended Action
Check that the memory modules have
been installed correctly and that proper
modules are used.
For systems with a graphics card:
1. Reseat the graphics card. Power on
the system.
2. Replace the graphics card.
3. Replace the system board.
For systems with integrated graphics,
replace the system board.
1. Upgrade the BIOS to proper ver-
sion.
2. Change the processor.
1. Check cable connections.
2. Run the Computer Setup utility and
ensure the device port is enabled.
1. Check the type of drive that you are
using and use the correct media
type.
2. Replace the CD with a new one.
Upgrade the BIOS to proper version.
1. Verify the correct ROM.
2. Flash the ROM if needed.
3. If an expansion board was recently
added, remove it to see if the prob-
lem remains.
4. Clear CMOS.
5. If the message disappears, there may
be a problem with the expansion
card.
6. Replace the system board.
No action required.
Product Name
SKU Number
Processor Type
Processor Speed
CPUID/PatchID
Cache Size
Memory Size
Integrated MAC
System BIOS
Chassis Serial Number
Asset Tag Number
UUID
Run HDD self-test for selected channel: SMART Status
Check, Short Self-Test, Extended Self-Test
View vendor, size, and firmware
Run SMART self-test for selected channel: SMART Sta-
tus Check, Short Self-Test, Extended Self-Test
Auto-detect HDD size and head
Set PATA Master/Slave device details on selected channel
to None, Auto, Manual
Set access mode on selected channel to CHS, LBA,
Large, Auto
View Firmware, Capacity, Cylinder, Head, Precomp,
Landing Zone, Sector
Allows you to set POST delay to 0, 5, 10, 15, or 30 seconds
Onboard LAN Disable/enable onboard LAN controller.
Onboard LAN Disable/enable the boot ROM of the onboard LAN chip.
Boot ROM
Onboard Allows you to select: Disabled, 3F8/IRQ4, 2F8/IRQ3, 3E8/
Serial Port 1 IRQ4, or 2E8/IRQ3.
Boot F9 Boot Menu Disables/enables F9 Boot Menu.
F10 Setup Disable/enable F10 Setup prompt on the logo screen.
Prompt
F11 Recovery Disables/enables F11 Recovery and provides the option of
showing the F11 Recovery prompt message on the logo
screen. Choose from the following: Disabled, Enabled no
prompt, Enabled and prompt.
F12 Boot Disables/enables the F12 Boot from LAN prompt message on
from LAN the logo screen.
Prompt
Hard Disk Allows you to specify the order of attached hard drive devices
Boot Seq. (USB HDD or USB flash media). The first attached drive in
the order has priority and is recognized as drive C.
Optical Drive Allows you to specify the order in which attached optical
Boot Seq. drives (including USB ODD) are checked for a bootable oper-
ating system image.
Network Boot Allows you to specify the order in which network devices
Seq. (including UP NIC cards) are checked for a bootable operat-
ing system image.
First, Second, Allows you to specify which devices will boot in which
Third, and sequence or to disable any of the four: removable, CDROM,
Fourth Boot hard disk, or network.
Device
Set Supervisor Allows you to establish a password to enter Computer Setup
Password
BIOS Write Disables/enables BIOS upgrading.
Protection
Power After AC Allows you to select system power loss behavior: Off, On,
Power Loss Last State.
Wake on PCI Disables/enables waking up from S5 by PCI device.
Device from
S5
RTC Resume Disables/enables RTC (real-time clock) alarm.
Alarm
PC Health Chassis Allows you to disable/enable the chassis intrusion function
Opened Warn- and clear the intrusion warning: Disabled, Enabled, Clear.
ing
System Fan Disables/enables detection of system fan during POST.
Fail Check
Smart Fan Disables/enables Smart Fan functionality. Enabling optimizes
Function fan control for best acoustic behavior.
Current CPU View only
Temperature
Current Sys- View only
tem Temp
Current CPU View only
Fan Speed
Current Sys- View only
tem Fan
Speed
Exit Save and Exit Allows you to save current settings and exit Computer Setup.
Setup
Discard Allows you to exit Computer Setup without saving changes.
Changes and
Exit
Load Opti- Allows you to reset Computer Setup to factory defaults.
mized defaults

Password Security

Resetting the password jumper
1. Shut down the operating system properly, then turn off the computer and any external devices,
and disconnect the power cord from the power outlet.
2. With the power cord disconnected, press the power button again to drain the system of any
residual power.
3. Remove the access panel.
4. Locate the header and jumper labeled PSWD.
5. Remove the jumper.
6. Plug in the computer and turn on power.
7. When you see the HP logo screen, turn off the computer. This clears the current passwords.
8. Replace the jumper to its original position.
9. Replace the access panel.
10.reconnect external equipment.
11.Plug in the computer and turn on power. Allow the operating system to start.
Resetting the CMOS jumper
1. Turn off the computer and any external devices, and disconnect the power cord from the
power outlet. The power must be disconnected from the system to clear CMOS.
2. Disconnect the keyboard, monitor, and any other external equipment connected to the
computer.
3. Remove the access panel.
4. Locate the header and jumper labeled CMOS.
5. Remove the CMOS jumper from pins 1 and 2 and put the jumper on pins 2 and 3. This clears
CMOS.
6. Put the jumper back on pins 1 and 2.
7. Replace the access panel.
8. Reconnect the external equipment.
9. Plug in the computer and turn on power.
NOTE: Use Computer Setup to reset any special system setups along with the date and time.
page 3