Page of 12

HP Designjet 3D Assembly Instructions Manual

Hp designjet 3d material bay assembly instructions.
Hide thumbs
HP Designjet 3D Material Bay
Assembly Instructions
HP Designjet 3D Material Bay
Instructions d'assemblage
HP Designjet 3D Material Bay
Montageanleitungen
HP Designjet 3D Material Bay
Istruzioni di assemblaggio
HP Designjet 3D Material Bay
Instrucciones de montaje
HP Designjet 3D Material Bay
組立説明書
HP Designjet 3D Material Bay
组装说明
CQ708-90001
CQ708-90001
Read these instructions carefully...
Because of the weight of the printer you will need two people to install the material bay. When more than one person is
needed the symbol below is displayed.
Lisez attentivement les instructions suivantes...
En raison du poids de l'imprimante, deux personnes sont nécessaires pour installer la baie de matériau. Lorsque plus d'une
personne est nécessaire, le symbole ci-dessous est affiché.
Lesen Sie diese Anleitung sorgfältig durch...
Für die Montage des Materialfachs sind aufgrund des hohen Gewichts des Druckers zwei Personen nötig. Wenn mehr als
eine Person gebraucht wird, wird das folgende Symbol angezeigt.
Leggere queste istruzioni attentamente...
A causa del peso della stampante, sarà necessario l'aiuto di un'altra persona per installare l'area materiali. Ogniqualvolta
occorrerà l'aiuto di un'altra persona verrà visualizzato il seguente simbolo.
Lea atentamente estas instrucciones...
Debido al peso de la impresora, son necesarias dos personas para instalar el compartimento de material. Cuando se
necesite más de una persona, se mostrará el símbolo a continuación.
説明書をよくお読みください ...
このプリンタは重量がありますので、材料ベイのインストールは 2 人で行ってください。複数の人数が必要な手順には、
下のマークが表示されています。
请仔细阅读以下说明 ...
由于打印机很重,需要两个人来安装材料分隔间。如果需要多个人,则会显示下面的符号。
1
To unpack the material bay you will need at least 1 x 2
m (40 x 80 in) of work space.
Pour déballer la baie de matériau, vous aurez besoin
d'un espace de travail d'au moins 1 x 2 m.
Zum Auspacken des Materialfachs benötigen Sie
mindestens 1 m x 2 m Arbeitsfläche.
Per estrarre l'area materiali dalla confezione occorre
uno spazio di lavoro di almeno 1 x 2 m (40 x 80
pollici).
Para desembalar el compartimento de material
necesitará por lo menos un espacio de 1 x 2 m (40 x
80 pulgadas).
材料ベイを開梱するには、最低 1 x 2 m (40 x 80 イ
ンチ ) のスペースが必要です。
要拆开材料分隔间包装,至少需要 1 x 2 米
(40 x 80 英寸)的工作空间。

Advertising

   Also See for HP Designjet 3D

   Related Manuals for HP Designjet 3D

   Summary of Contents for HP Designjet 3D

  • Page 1

    HP Designjet 3D Material Bay Read these instructions carefully... Assembly Instructions Because of the weight of the printer you will need two people to install the material bay. When more than one person is needed the symbol below is displayed.

  • Page 2

    Abra la caja, déjela a un lado y retire el contenido. Esta caja contiene: Open box, lay on side and remove contents. This box contains: Un (1) compartimento de material con cable de comunicación y tubos de material. One (1) material bay with communication cable and material tubes. Un (1) cartucho de material de modelo.

  • Page 3

    Open material bay doors, remove material bay Open material bay box, remove material bay cable Remove material bay from protective bag. Unfold the 2 tabs of the material bay cardboard insert cardboard insert and recycle. and material tubes (2) taped to the bag and set aside and open.

  • Page 4

    From the display panel press Material. Press Unload. Press Unload Both. Open material bay doors and remove model and Note: Unloading may take up to 5 minutes. support material carriers. Dans l'afficheur, appuyez sur Matériau. Appuyez sur Décharger... Appuyez sur Décharger les deux. Ouvrez les portes de la baie de matériau et retirez les Remarque : Le déchargement peut prendre jusqu’à...

  • Page 5

    Open model carrier and rewind the material, leaving Turn the power switch to the off (O) postion. Turn the circuit breaker to the off (O) position. Disconnect the network cable. 6.5mm (0.25 inch) of material at the material guide tube. Repeat for support carrier. Mettez l'interrupteur sur la position d'arrêt (O).

  • Page 6

    Disconnect the power cable. At rear of printer disconnect the material bay cable Disconnect the support material tube (S1) at the At rear of printer, disconnect the model material tube from the printer and the material bay. support Y connector (S) and material bay (S) by (M1) at the model Y connector (M) and material bay pressing the coupler ring in and pulling the tube out.

  • Page 7

    Position the second material bay on top of first material bay aligning pins and feet as shown. With 2 people lift the printer off of the material bay With 2 people position printer on top of material bays and place on a stable surface. by aligning pins and feet as shown.

  • Page 8

    Locate material tubes that were removed from top of At rear of printer, connect short red striped material tube (M1) to material bay model coupler (M). Connect other end to left Repeat using black striped material tube (S1) and black material bay.

  • Page 9

    Remove the Y connector plugs by pushing the coupler Repeat steps 22 and 23 using the longer material tubes Locate material bay cable that was shipped with the Connect cable from rear of printer to upper connector rings in and pulling the plugs out. (M2 and S2) that were shipped with the material bay.

  • Page 10

    Connect second cable from lower connector of first Reconnect power cord between rear of printer and Reconnect network cable between network port and At rear of printer turn circuit breaker to ON (I) position. material bay to upper connector of second material dedicated power outlet.

  • Page 11

    From left side of printer turn power switch to ON (I) Load new material carriers with material spools. From display panel press Material. Display will show Open material bay doors and push both support position. Reload material after printer has reached Idle. carriers (black handles) into left side of the material Add/Remove.

  • Page 12: Legal Notice, Avisos Legales

    M1 à la première baie de matériau de modèle. S2 et M2 font référence à la seconde baie de matériau. © 2010 Hewlett-Packard Development Company, L.P. La información contenida en este documento está sujeta a cambios sin previo aviso. Las Wenn das Auffüllen des Materials fertig ist, drücken Sie únicas garantías de los productos y...

Comments to this Manuals

Symbols: 0
Latest comments: