Haier HW85-B1486NZP Operating Instructions

Haier Automatic Drum Washer
Operating Instructions
Contents
1. Notice before Use
Models:
2. Safety Precautions
3. Precautions for Use
Temp.
Wash HW85-B1486NZP
Rinse Speed
Spin Auto 4. Preparations before
Strong Delay Prewash Anti-crease Start/Pause
Washing
5. Operational Procedure
6. Control Panel and
Program Description
7. Display Screen
Description
8. Other Functions
9. Fault Clearance
10. Cleaning/Maintenance
Technology of automatic closedown upon
clean detected
Real-time door open
Automation technology
Crease-resistant and soak function
Please read these instructions carefully before use.
Technology of anti-bacteria and
Please save these instructions for future reference.
mildew-proof with window pad
Self-cleaning function
Foam self-checking function
Power-off memory function
Technology of variable frequency drive
Specifications
Power supply
Water inlet pressure 0.001
Certificate of Quality
Rated washing capacity
Rated spinning capacity
Spinning speed
1,400 rpm Inspector:
Washing noise
53dB (A weighted)
Spinning noise
71dB (A weighted)
Energy efficiency rating
Grade 1
Haier Group
Dimensions (H×D×W) 850mmX650mmX595mm
Qingdao Haier Drum Washer Co., Ltd.
Address: Haier Industrial Park, Qingdao Hi-tech
Applicable standard: GB/T 4288-2008 Household and Similar Electrical
Industrial Development Zone
Washing Machine. Tel: 4006 999 999
Fax: 0532-87636565
The diagrams in this manual are for illustrative purpose only. Due to Postal code: 266101
Website: www.haier.com
continuous product improvement, please see the actual product for the
Customer service e-mail: 9999@haier.com
appearance, color and accessories which may be inconsistent with those
Headquarters address: No. 609, 308 National
described in this manual. Here we apologize for this.
Highway, Qingdao
This product is classified as Class I appliance. Please pay attention to
Version: 1st version, 2009
electrical safety during use.
Special No.: 0020505574A
V98497
Please install and adjust the washer
1. Notice before Use
according to the instructions in this manual
so that you can use it in a safer manner.
To connect the water inlet pipe
Drain pipe
support
1. Select a proper water tap
Distributor boxes
(Add a proper amount of
detergent required by washing)
Pre-washing detergent box
Water inlet
The length of front end must be more than 10mm. In
pipe joint Washing detergent box
case of unsmooth end face of the water tap outlet,
please file it smooth to avoid water leakage.
Softener and bleacher box
2. Remove the water inlet pipe joint
When selecting the pre-wash function or the
Press the lower end of locking
pre-wash program, add detergent into the
lever; pre-washing chamber to pre-wash the clothes;
Locking
Hold the water inlet pipe, press As for the dosage of detergent, please refer to the
lever
down the slider and remove Slider instructions for detergent. Excessive detergent
the water inlet pipe joint; may result in too many bubbles and spill as well
Remove the nameplate. Water inlet pipe
as affect its dissolution. Special low foaming
detergent for drum washers shall be used. When
Wall
washing synthetic or wool fabrics, be sure to use
3. Install the water inlet
If the water tap is
special detergent;
placed against the
wall, you may turn pipe joint Do not allow the level of softener or liquid
this screw to a proper detergent to exceed the "MAX" mark of distributor
position in advance. Loosen the nut to the extent that approximate
box. Concentrated softener or liquid detergent
3-4 turns of screw thread are exposed;
Loosen four screws of the water inlet pipe should be diluted before being added into
joint to the extent that the joint can be ringed distributor box. Excessive softener may damage
onto the water tap; the synthetic fiber. As for the dosage of softener,
If the water inlet pipe joint cannot be ringed please refer to its instructions.
onto the water tap, please remove the
bushing and install again;
Turn one of screws to an approximately
Bushing
proper position in advance, ring the water
inlet pipe joint onto the water tap, then evenly
3-4 turns tighten the remaining three screws in place,
and finally tighten the nut.
Nameplate
Nut
4. Connect the water inlet pipe
Press down the slider and insert the water
pipe into the water inlet pipe joint;
Hook the water inlet pipe joint with the
locking lever, then loosen the slider until a
Locking
"poop" is heard.
lever
5. Connect to the washer
Ring the nut at the other end of water inlet
pipe onto the water inlet valve joint;
Tighten and confirm the nut of water inlet
pipe in place.
6. Check the water inlet pipe for
good connection
Check for firm connection;
After installation, turn on the water tap and
check for water leakage;
Before every use of washer, please check
for good connection between the water inlet
pipe and the water tap;
Never forcibly bend the water inlet pipe.
To paste the felt and install
the Noise Reduction Board Drain pipe
1. Paste the felt on one side of the Noise
The outlet end of drain pipe must be
Reduction Board.
higher than 80cm and the highest point
2. Incline the washer backwards and remove the
must be less than 100cm. To prevent the
four feet (Fig. 1);
drain pipe from coming off, you may
3. Place the side with felt of splash plate
secure it to its clamp at the back of
inwards, install the foot bolts through the four
washer or to the firm support as shown
holes on the shell and tighten them (Fig. 2),
in the figure.
then level the washer.
It is not recommended to extend the
drain pipe. If the extended pipe exceeds
2.5m in length, water feeding and
drainage may easily occur at the same
time. Please contact our After-sales
Service Department for extending the
drain pipe.
Fig. 1 Fig. 2
Table top
2. Safety Precautions
Main control
panel
Electrical safety
prompt: Please pay
front board
attention to electrical
safety when using
the washer.
Inner drum
Window pad
Warning sign: The
contents with this
sign involve the
safety of both the
product and user. Be
sure to strictly follow
these instructions,
otherwise the
washer may be
damaged or the user
may be injured.
Filter door
Sight glass
Bottom trim
Door
Foot
Packaging bolts and accessories
Packaging bolts and accessories are used to fix
Prohibitory sign: The
Table top internal components of the washer during transport
contents with this
and should be removed before using the washer.
sign indicate the
behaviors to be
absolutely
Water inlet valve
prohibited. Failure to
follow these
Power cord
instructions may
result in damage to
the washer or
Screw (4 pcs) personal injury.
Power plug
Unscrew packaging bolts and take out
Back cover plate
the back-up block.
Drain pipe clamp
5. Operational Procedure
Drain pipe
Splash-proof plastic
plug (4 pcs)
Connect the
1
Shell water inlet
pipe, turn on
Block the bolt hole with a splash-proof
the water tap
plastic plug.
Please keep such disassembled components as
packaging bolt and back-up block in a safe place for
future handling of the washer.
3
Place the
drain pipe
To adjust
the feet Accessories
Be sure to
adjust the
Water inlet pipe assy Felt
four feet to
level the
washer
before use.
Operating
Note Noise Reduction Drain pipe support
Instructions Operating Instructions Haier Automatic Drum Washer Contents
Board Models: 2. Safety Precautions 3. Precautions for Use 4. Preparations before Washing 5. Operational Procedure 1. Notice before Use
Description 8. Other Functions 7. Display Screen 9. Fault Clearance Program Description 6. Control Panel and
11. Warranty Instructions clean detected Technology of automatic closedown upon Automation technology 10. Cleaning/Maintenance Real-time door open
After finishing the adjustment of Please read these instructions carefully before use. This product is only for sale in Mainland China. Please save these instructions for future reference. Self-cleaning function Technology of variable frequency drive Foam self-checking function Power-off memory function mildew-proof with window pad Technology of anti-bacteria and Crease-resistant and soak function
the four feet, turn the foot
support nut to cling to the shell Warm Tips Card
in order to support the washer.
3. Precautions
for Use
1. Due to the fluctuation of water pressure, please check all the joints of water inlet
1. The plug should be accessible after the washer is
pipe, water tap and drain pipe for firm connection before washing every time. In
installed in place. Do not disconnect the plug case of loose water pipe connection or water leakage, please turn off the water
from the socket by pulling the power cord. If the tap and take proper measures or contact our After-sales Service Department for
power cord needs to be replaced, ask a qualified reconnection. Only after such faults are cleared can you use it again.
person or contact our After-sales Service
2. When the washer is not in use, please keep the door slightly open to avoid
Department for replacement. Prevent the power
unpleasant smell. Do not cover the washer with a plastic bag to avoid moisture
cord from being pressed by any foot and from
staying in the washer.
such problems as break-off, flattening, etc.
3. Do not place any heavy object, heat-producing appliance and item liable to
water/liquid leakage to avoid the deformation of table top and plastic parts.
2. Power supply must use an independent socket,
4. Do not wash such waterproof articles as raincoat, bicycle cover and down
the grounding terminal of which must be properly
products as well as carpet to avoid abnormal vibration or the damage to articles.
grounded. The socket must be a qualified product
5. Do not open any detergent distributor box during the program operation to avoid
with the following 3C certification mark:
some detergent leaving in the box.
6. If a brassiere with steel wire is washed in the washer, the steel wire may bounce
3. Such overload protective devices as suitable fuse must be available
out. Therefore, do not wash any brassiere with steel wire in order to protect the
at the user's home. And, the ammeter, wire and socket must be able
washer.
to withstand 10A current.
7. The washer's door is equipped with self-lock safety device. Only when the
washer is in safe state (the water level is below the lower edge of sight glass,
the temperature inside of the drum is 50°C, the inner drum is not rotating) can
1. Keep the washer away from any heat source and direct sunlight to prevent
you unlock the door. Never forcibly open the door before the washer reaches
the aging of plastic and rubber parts.
the safe state to avoid damage to the door or scald. "Click" will be heard when
opening the door. It is normal and arises from the working principle of
electromagnetic lock's internal structure.
1. Do not use such chemicals as flammable detergent and 8. Turn off the water supply and power supply after finishing washing every time.
Moreover, clean the sight glass window pad interlining to prevent contaminants
dry-cleaning solvent to wash the clothes. Do not use any
from tainting the clothes again.
organic solvent or corrosive liquid to wipe the exterior and
9. It is recommended that the washer be installed in a location with floor drainer.
rubber parts of the washer. Do not use any flammable spray
10. Using the washer in the environment with the temperature at 0°C or below 0°C
near the washer. In case of flammable gas leakage, do not plug or unplug the
may damage the water inlet valve and drainage system. If the washer is stored
washer's power plug. Do not use the washer near the environment with
flammable and explosive gas & liquid such as biomass pool, etc. in the environment with the temperature at 0°C or below 0°C, be sure to move
and leave it in the environment at room temperature for 2-4 hours before use.
2. The washer's door is relatively hot during heating. For the purpose of safety,
11. Do not put the clothes tainted with chemicals into the washer.
keep the children away from the washer. In addition, when draining hot water,
12. Washing, drying capacity
be careful to avoid scald.
3. After unpacking the washer, do not allow the children to play with the
disassembled packaging materials such as carton, plastic packaging bag and
foam, etc.
Type of clothes Fadeless cotton fabric
4. Do not install the washer outdoors and in excessively humid environment,
otherwise moisture on the electrical components may easily cause damage to
HW85-B1486NZP 8.5kg
the ignition system or other accidents. In case of inadvertent water spray onto
or into the washer, only after the washer is thoroughly dried can you use it.
5. Neither place the washer directly onto the airproof carpet nor close up to the
According to the max washing capacity specified in A.4 of
wall or furniture to avoid accidents. The carpet must not block the bottom vent. Note
Appendix A to the standard GB/T4288-2008.
Do not use the washer on any platform higher than the floor, otherwise it may
For energy efficiency test program, please select "cotton +
fall off onto the floor and be damaged.
60°C + strong wash + max washing capacity + max speed".
2 Insert the power
plug into the
power socket
Select washing time, times of rinsing,
7
spinning speed, strong wash, pre-wash ,
etc. as required.
After finishing washing, the washer will
automatically switch off.
4. Preparations
before Washing
Check the clothes for special washing
requirements and make sure that the clothes
are suitable for washing with washing machine
and water in order to avoid the deformation
and damage of the clothes.
For the clothes tainted with much
mud and dust, please remove
them before washing.
Wash those clothes liable to color fading
separately from other clothes.
Check pockets and remove
coins, sand, hairpin and other
things from them.
Tie the ties, buckle the buttons, zip the
zippers and sew the openings.
To avoid the sound from
buttons, please turn those
clothes with buttons inside out
before putting them into the
washer.
Please unfold and fluff out the clothes before
putting them into the washer. Furthermore,
do not overload the washer.
When washing small articles (e.g.
handkerchief, gloves, socks, etc.) and those
clothes liable to intertwist and wear, please
put them into net bags for washing, rinsing
and spinning to prevent them from falling into
between the inner drum and window pad and
further avoid incomplete washing or damage
Terylen to top-grade clothes. The weight of articles in
fabric/blend
each net bag should not exceed 300g and
Wool fabric Silk fabric
fabric/chemical
fiber fabric the net bags should not be washed together
with those clothes not in a net bag, otherwise
4kg 2kg 2kg the washer will not be balanced, resulting in
abnormal vibration.
Reference weights for small articles:
handkerchief: about 30g/piece; gloves:
about 60g/pair; cotton socks: about
30g/pair; silk socks: about 20g/pair.
Open the door, put the clothes into the
5
washer, close the door, then add a proper
4 Turn on
amount of detergent into the distributor
the power
box and close the distributor box.
switch
(Refer to "Distributor Boxes" in "Notice before
Use" section for details.)
6
Select the
desired program
Heavy
Underwear
Wash Temp. Silk Sport wash
Wool Night
Rinse Speed
Synthetic Quick
Power
Memory Spin
Spin Auto
Cotton Tub Clean 8.5kg
Start/Pause
Strong Delay Prewash Anti-crease
HW85-B1486NZP
Press and hold 2seconds
to set door unlocked
8 "Delay" program is off by default.
To activate this program, press
Start the
9
"Delay" button to make settings.
selected
program.