6 • Assembling the Blades . . . . . . . . . . . . . . 11 • To reduce the risk of fire, electrical shock, or motor damage, do not use a solid-state speed control with this fan. Use only Hunter speed 7 • Completing Your Installation With a Multi Staked Light Fixture .
If you want to use an existing fan site, complete the following checklist to System determine if the site is acceptable and safe for your new Hunter fan. If you cannot check off every item, prepare a new fan site as described on this page.
Page 4
ANSI/NFPA 70. If your ceiling fan, go to your fan manual and continue with Section 2 • Installing the you are unfamiliar with wiring, use a Hanger Bracket. qualified electrician. 42882-01 • 12/14/10 • Hunter Fan Company...
Page 5
To install and use the accessories, follow the instructions included with each product. For quiet and optimum performance of your Hunter fan, use only Hunter speed controls. Low Profile Mounting fits close to the ceiling, recommended for ceilings less...
• Drill holes for and install wood screws. • Identify and connect electrical wires. • Lift 40 pounds. If you need help installing the fan, your Hunter fan dealer can direct you to a licensed installer or electrician. Gathering the Tools You will need the following tools for installing the fan: •...
Tighten the screws into the 9/64” pilot holes; do not use lubricants on the screws. Do not over tighten. Flat Washer 3” Wood Screw Steps 2-4 – 2-6 42882-01 • 12/14/10 • Hunter Fan Company...
3-3. Install two locking screws through the holes in the side of the Square Hanger metal bracket to secure the square hanger. Motor Green Assembly Ground Wire Step 3-2 Green Ground Wire Step 3-3 #8-32 x 1” Screw Locking Screw 42882-01 • 12/14/10 • Hunter Fan Company...
4-7. Spread the wires apart, with the grounded wires on one side of the outlet box and the ungrounded wires on the other side of the outlet box. 42882-01 • 12/14/10 • Hunter Fan Company...
5-3. Install the two remaining canopy screws into the holes in the fan housing and into the hanger bracket. Securely tighten all screws. Fan Housing Keyhole Step 5-3 Canopy Screw 42882-01 • 12/14/10 • Hunter Fan Company...
6 • Assembling the Blades Step 6-1 (Detail) Hunter fans use several styles of fan blade irons (brackets that hold the blade to the fan). 6-1. Your fan may include blade grommets. If your fan has grommets, insert them by hand into the holes on the blades.
Align the side screw holes in the upper and lower switch housings. Attach the lower switch housing to the upper switch housing with three #6-32 x 3/8” housing assembly screws. Housing Assembly Screw Step 7-4 Plug Connector Detail 42882-01 • 12/14/10 • Hunter Fan Company...
Note: In compliance with US federal energy regulations, this ceiling fan contains a device that restricts its light output. Exceeding the wattage limit marked on the MAX wattage sticker affixed to the light socket(s) may result in fire hazard or improper operation. 42882-01 • 12/14/10 • Hunter Fan Company...
You may use an artistic agent, but never abrasive cleaning agents as they will damage the finish. 8-6. The blades on this fan have been treated with Hunter’s Dust Armor protection, making the blades less likely to attract dust and dirt. Use a dry or slightly damp lint free cloth to clean the blades.
If you need parts or service assistance, please call 888-830-1326 (In Canada, call 1-866-268-1936) or visit us at our Web site at http://www.hunterfan.com. Hunter Fan Company 7130 Goodlett Farms Pkwy. #400 Memphis, Tennessee 38016 42882-01 • 12/14/10 • Hunter Fan Company...