Yamaha EX5R Data List page 44

<MONO> 7EH
Cntrl# parameter Data Range
126 Mono 0...16
Performs the same function as when receiving ALL SOUNDS OFF. If the 3rd byte (mono) is
within 0 through 16, the channel will be Mode4(m = 1).
<POLY> 7FH
Cntrl# parameter Data Range
127 ----- 0
Performs the same function as when receiving ALL SOUNDS OFF. The channel will be Mode3.
6. CHANNEL AFTER TOUCH
STATUS: DnH
7. SYSTEM EXCLUSIVE MESSAGES
<UNIVERSAL REALTIME MESSAGES>
1) MIDI Master Volume (Receive only)
F0H,7FH,xnH,04H,01H,llH,mmH,F7H
xn:n=Device Number, xn=7F:Broadcast
ll:Don't care
mm:Master Volume
When received, Master Volume in the System Parameter will be changed.
2) MIDI Machine Control (Transmit only)
Transmits when MTC is selected for the timing clock.
2-1) STOP
F0H,7FH,7FH,06H,01H,F7H
Transmits when STOP is pressed.
2-2) DEFERRED PLAY
F0H,7FH,7FH,06H,03H,F7H
Transmits when RUN is pressed.
2-3) LOCATE
F0H,7FH,7FH,06H,44H,06H,01H,hrH,mnH,scH,frH,ffH,F7H
Transmits when moving in measures in the Song Play mode.
<UNIVERSAL NON-REALTIME MESSAGES>
1) GM System On (Receive only)
F0H,7EH,xnH,09H,01H,F7H
xn:n=Device Number, xn=7F:Broadcast
Resets all the data to their respective default values except for MIDI Master Tune.
2) ID Request(Receive only)
F0H,7EH,xnH,06H,01H,F7H
xn:n=Device Number, xn=7F:Broadcast
3) ID Reply(Transmit only)
F0H,7EH,0nH,06H,02H,43H,00H,41H,02H,xxH,00H,00H,00H,7EH,F7H
0n:n=Device Number
xx:33(EX5),34(EX5/5R),40(EX5R)
Transmits ID Reply when ID Request is received.
<PARAMETER CHANGES>
F0H,43H,1nH,idH,ahH,amH,alH,ddH,~,ddH,F7H
1n:n=Device Number
id:ID=5B,57
ah:Address High
am:Address Mid
al:Address Low
dd:Data
ID = 5BH
1) Current Performance / Common Parameters
2) Current Performance / Part Parameters
3) Current Voice / Common TG Parameters
4) Current Voice / Common Control Parameters See < Table 4>
5) Current Voice / Element Parameters 1
6) Current Voice / Element Parameters 2
7) Remote SW
1) an 2) are effective only in the Performance mode.
3)~6) are effective only in the Voice mode.
7): receive only.
ID = 57H
1) Current VL Parameter
Effective only in the Voice mode.
[Other]
MIDI Master Tune (Receive only)
F0H,43H,1nH,27H,30H,00H,00H,mmH,llH,ccH,F7H
1n:n=Device Number
mm:Master Tune MSB
ll:Master Tune LSB
cc:Don't care
When received, Master Tune in the System Parameter will be changed.
AH AM AL
See < Table 1> 10 ** **
See < Table 2> 3p ** **
See < Table 3> 40 ** **
50 ** **
See < Table 5> 60 ee **
See < Table 6> 70 ee **
See < Table 16> 0A 00 **
AH AM AL
See < Table 7> 20 ** **
p = Part No.(0~F:Part1~Part16)
ee = Element No.(00~7F:EL1~EL128)
** = Address (Refer to the tables)
<BULK DUMP>
F0H,43H,0nH,idH,bhH,blH,ahH,amH,alH,ddH,~,ddH,ccH,F7H
0n:n=Device Number
id:ID=5B,57
bh:Byte Count High
bl:Byte Count Low
ah:Address High
am:Address Mid
al:Address Low
dd:Data
cc:Check Sum
ID = 5BH
1) Current Performance / Common Bulk
2) Current Performance / Part Bulk
3) 1 Performance Bulk
4) Current Voice / All Bulk
5) Current Voice / Element Bulk
1) and 2) are effective only in the Performance mode.
4) and 5) are effective only in the Voice mode.
ID = 57H
1) Current VL Bulk
2) 1 VL Bulk
1) is effective only in the Voice mode.
<BULK DUMP REQUEST>
F0H,43H,2nH,idH,ahH,amH,alH,F7H
2n:n=Device Number
id:ID=5B,57
ah:Address High
am:Address Mid
al:Address Low
Receive only.
Responds to all the Bulk Dumps.
See MIDI Data Table for Address and Byte Count.
The Check sum is the value that results in a value of 0 for the lower 7 bits when the Byte
Count, Start Address, Data and Check sum itself are added. When receiving the Bulk Dump with
the wrong check sum, a check sum error will be displayed.
8. SYSTEM COMMON MESSAGES
<MIDI TIME CODE (Quarter Frame Message)>
F1H,nxH
nx:data
Receives when MTC is selected for the timing clock.
<SONG POSITION POINTER>
F2H,llH,mmH
ll:Song Position LSB
mm:Song Position MSB
Transmits when moving in measures in the Song Play mode.
Receives when in the standby status in the Song Play mode.
9. SYSTEM REALTIME MESSAGES
Can transmit and receive.
<TIMING CLOCK>
STATUS: F8H
<START>
STATUS: FAH
<CONTINUE>
STATUS: FBH
<STOP>
STATUS: FCH
<ACTIVE SENSING>
STATUS: FEH
Once FE (Active Sensing) has been received, if no MIDI data is subsequently received for
longer than an interval of approximately 300msec, the EX will perform the same function as
when All Sounds Off, All Notes Off, and Reset All Controllers messages are received, and
will then return to a status in which FE is not monitored.
44
AH AM AL
See < Table 8> 10 00 00
See < Table 9> 3p 00 00
See < Table 10> 11 00 nn
See < Table 11> 40 00 00
See < Table 12> 60 ee 00
AH AM AL
See < Table 14> 20 00 00
See < Table 15> 31 00 nn
p = Part No.(0~F:Part1~Part16)
b = Memory Bank(1~4:P1,P2,I1,I2)
ee = Element No.(00~7F:EL1~EL128)
nn = Memory No.(Refer to the tables)