Advertisement
Quick Links
• PLEASE study these instructions carefully before installing your new camshaft. If you have any questions or problems, do not hesi-
tate to call our Technical Hotline at: 1-800-416-8628.
• CAMSHAFT: Edelbrock Performer RPM camshafts are ground specifically for use with the corresponding Performer RPM manifold.
The Performer RPM manifold #7176, and Performer RPM camshaft #7177, are designed to work as a team to give you better drive-
ability and performance. They are dyno-matched and street-proven. For best results, use the Edelbrock manifold/camshaft package
with the carburetor and headers we recommend. The Performer RPM camshafts are designed for use with modified or high perfor-
mance cylinder heads or #6077 Performer RPM cylinder heads and valve train components only. H.P. adjustable rocker arms or
adjustable pushrods must be used. The parts described here will physically fit 318 c.i.d. engines, but users should be advised that these
parts were developed for optimum performance in engines of 340-360 cubic inches. When using a 318 c.i.d. engine, we strongly rec-
ommend the use of late model 360 cylinder heads. This is due to the extremely small intake and exhaust ports which can severely
limit performance when 318 cylinder heads are used.
NOTE: Maximum performance is achieved only when the Edelbrock Performer RPM Total Power Package components are used with
the following equipment:
•
Performer RPM manifold/camshaft/timing set/valve springs
•
Performer RPM cylinder heads, #6077
•
Performer Series carburetor #1407 (750 cfm)
•
fuel delivery system of sufficient capacity
•
1-3/4" headers
•
aftermarket/re-curved distributors
• IMPORTANT: This instruction sheet provides general installation guidelines which can affect your warranty. Read it carefully. It is
not our intent to cover each detail of installation here; a step-by-step procedure manual would be far too lengthy. We want to caution
you that installing a camshaft is a complicated procedure that requires a good general knowledge of automotive engines. If you are not
confident that you can complete the camshaft installation successfully, we suggest you consider having it installed by an experienced
mechanic.
CAUTION: Improper installation will result in LOW MILEAGE, POOR PERFORMANCE, COSTLY REINSTALLATION,
and ENGINE DAMAGE.
TO AVOID THESE PROBLEMS YOU MUST DO THE FOLLOWING:
Carefully study and understand all instructions.
Examine the camshaft for possible shipping damage (if damaged contact your dealer immediately).
•
TOOLS AND EQUIPMENT
Use the following checklist for items needed.
box and open-end wrenches
socket set
distributor wrench
pliers (channel locks & hose clamp)
screw drivers (regular and phillips)
torque wrench
hammer
gasket scraper or putty knife
timing light
vacuum gauge
rags
water bucket
harmonic balancer puller
©1998 Edelbrock Corp
MODEL: 340-360 c.i.d. Chrysler V8, 1967 & 1985
PREPARATION CHECKLIST
•
Camshaft/Lifters/Lube Kit
HARDWARE & PARTS TO BUY
gaskets- Edelbrock, OEM or equivalent
pipe plugs, if needed
Edelbrock Gasgacinch, #9300
RTV Silicone
chalk
paper and pencil
radiator coolant
teflon tape
Edelbrock Performer-Link True Rolling Timing Chain and
Gear Set #7803
Edelbrock Sure Seat Valve Springs, #5777
Intake gaskets- Fel-Pro Printoseal or equivalent
Manifold bolt kit #8579
PERFORMER RPM
CATALOG #7177
Rev 9/98
Advertisement
Related Manuals for Edelbrock Performer RPM 1967
Summary of Contents for Edelbrock Performer RPM 1967
- Page 1 360 cylinder heads. This is due to the extremely small intake and exhaust ports which can severely limit performance when 318 cylinder heads are used. NOTE: Maximum performance is achieved only when the Edelbrock Performer RPM Total Power Package components are used with the following equipment: •...
- Page 2 1. This camshaft is designed to function with Edelbrock Sure Seat valve springs #5777. Do not use dual valve springs with this camshaft. Special H.P. retainers may be necessary with your installation for proper spring height.
- Page 3 In order for this Performer RPM cam and lifter kit to be cov- ered under ANY WARRANTY you MUST use the correct Edelbrock Sure Seat Valve Springs. The end flap or label from your Sure Seat Valve Spring box must be sent in with your camshaft warranty card.
- Page 4 • CAUTION: Use Edelbrock Performer-Plus Timing Chain and Gear Set #7803. Do not use late model timing chain and gear sets that are designed for emission-controlled engines. These timing sets are machined in a retarded position and are not rec- ommended for this camshaft installation.
- Page 5 These timing sets are machined in a retarded position and are not recommended for this camshaft installation. Edelbrock Timing Sets feature three keyways for specified timing selection. CAMSHAFT: Performer RPM Hydraulic CATALOG #7177 ENGINE: Chrysler 340-360 c.i.d.