Surround Play - Kenwood KRF-V5050D Instruction Manual

Surround Play

The DTS compatible models can reproduce a CD, DVD, or LD carrying
the DTS mark.
DOLBY DIGITAL can be used when playing DVD or LD software bearing the
mark and DOLBY DIGITAL format digital broadcasts (etc.).
DOLBY PRO LOGIC and DOLBY 3 STEREO can be used when playing
video, DVD, or LD software bearing the
INPUT MODE
LISTEN MODE
LISTEN MODE
LSTN M.
SELECTOR
RC-R0616
Preparations
• Turn ON related components.
• Complete "Preparing for surround sound" (speaker settings). *
• Use the INPUT SELECTOR to select the component you wish to
play back with surround sound.
• Use the INPUT MODE key to select the input mode (analog or digital)
for the source you wish to play back.
• Noise will be produced when a DTS source is played by selecting the
analog input.
1
Start playing the video software.
2
Press the LISTEN MODE (LSTN M.) key to select the
listening mode.
The listening mode settings are stored separately for each input. If the
input mode is set to digital auto ("AUTO SOUND" lights), the receiver
selects the optimal listening mode automatically based on the type of
input signal and the speaker settings.
Each press of the LISTEN MODE (LSTN M.) key switches the
setting as listed below.
The listening mode settings are different depending on the
type of input signal.
When the DOLBY DIGITAL signal is input:
1 DOLBY DIGITAL: DOLBY DIGITAL surround (The
DOLBY DIGITAL indicator lights up.)
2 PRO LOGIC: PRO LOGIC surround (The PRO LOGIC
indicator lights up.)
3 3 STEREO: 3-STEREO surround (The 3 STEREO
indicator lights up.)
4 STEREO: Normal stereo playback
When you select DOLBY DIGITAL
SP A B TI.VOL
L C R
CLIP MUTE
LFE
RDS EON PTY
SL S SR
TP TA NEWS
mark.
INPUT SELECTOR
INPUT
RC-R0512
FM AUTO SOUND DIGITAL AUTO
AM PRO LOGIC S.DIRECT MEMO
MHz 3 STEREO MONITOR
kHz DOWN MIX DSP TUNED
When the DTS signal is input:
(The DTS indicator lights up.)
1 DTS: DTS surround
2 STEREO: Normal stereo playback
When the analog or digital signal (except for the DOLBY
DIGITAL or DTS signal) is input:
1 PRO LOGIC: PRO LOGIC surround (The PRO LOGIC
indicator lights up).
2 3 STEREO: 3-STEREO surround (The 3 STEREO indi-
cator lights up.)
3 ARENA: DSP surround.
4 JAZZ CLUB: DSP surround.
5 THEATER: DSP surround.
6 STADIUM: DSP surround.
7 DISCO: DSP surround.
8 STEREO: Normal stereo playback. Sound is produced
from the two front channels only.
• If a Dolby Digital signal having more channels than the maximum
number of playback channels available using the receiver's current
settings is input, the DOWNMIX indicator on the front panel lights
up and downmixing is performed to match the number of available
3
channels.
Adjust the volume.
Notes
• Depending on the type of the signal or speaker setting, some listening
modes cannot be selected.
• When playback is started, the sound may be cut or interrupted before
the input source is confirmed as Dolby Digital.
• To enjoy Dolby Digital surround (as well as all the other listening
modes) from a single component, be sure to use a Dolby Digital
compatible source component. Connect the Dolby Digital compatible
source component's Dolby Digital format digital audio signal to one of
the DIGITAL INPUT jacks on the back of the receiver. Connect the
8
normal audio signal correctly to the respective component's AUDIO
jacks.
ST.
Ambience effects
29
90!@