Kenwood KVT-739DVD Installation Manual
Monitor with dvd receiver
Hide thumbs
Also See for KVT-739DVD:
- Service manual (114 pages) ,
- Instruction manual (100 pages) ,
- Installation manual (25 pages)
Advertisement
Quick Links
Advertisement
Related Manuals for Kenwood KVT-739DVD
Summary of Contents for Kenwood KVT-739DVD
- Page 1 MONITOR WITH DVD RECEIVER KVT-739DVD INSTALLATION MANUAL © B54-4518-00/00 (MV/XV)
- Page 2 Accessories ..1 ..2 ..1 ..4 ..1 ..4 ..1 ..2 ..1 ..1 ..2 ..4 ..4 KVT-739DVD...
-
Page 3: Installation Procedure
Installation Procedure ¤ 1. To prevent a short circuit, remove the key from the ignition and disconnect the - battery. • If the power is not turned ON (or it is ON, but will be OFF 2. Make the proper input and output wire immediately), the speaker wire may have a short-circuit connections for each unit. - Page 4 Connect to the terminal that is grounded when either the telephone rings or during conversation. Mute wire (Brown) To connect the Kenwood navigation system, consult your navigation manual. Depending on what antenna you are using, Motor antenna control wire (Blue) connect either to the control terminal of the motor antenna, or to the power terminal for the booster amplifier of the film-type antenna.
- Page 5 Receiver unit Accessory # The cable (Accessory 3) is fixed with a chassis using Accessory 3 harness band (Accessory Receiver unit FM/AM antenna input Wiring harness (Accessory 1) REVERSE White/Black ILLUMI To front left speaker White Gray/Black REMO.CONT To front right speaker Gray MUTE Green/Black...
-
Page 6: System Connection
System Connection To Relay Box Accessory 4 Receiver unit ■ Front Preout • Audio left output (White) • Audio right output (Red) ■ Rear Preout • Audio left output (White) • Audio right output (Red) ■ Subwoofer Preout • Audio left output (White) •... -
Page 7: Optional Accessory Connection
Optional Accessory Connection iPod (commercially available) KCA-iP300V (Optional Accessory) Audio Input Resistance-free stereo type mini plug (3.5Ф) Audio Output (Black) Visual Input Resistance-free mini plug (3.5Ф) Monitor/Player unit Visual Output (Yellow) USB terminal USB terminal Receiver unit Accessory 3 Connection cable Connection cable (Included in the Navigation System) (Included in the Disc changer) - Page 8 Installation for Monitor/Player Unit Firewall or metal support Screw (M4X8) (commercially available) Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. Accessory 6 Self-tapping screw Metal mounting strap (commercially available) (commercially available) Make sure that the unit is installed securely in place.
-
Page 9: Removing The Unit
Removing Monitor/Player Unit Removing the Hard Rubber Frame Removing the Unit (escutcheon) 1. Remove the hard rubber frame by referring to the removal procedure in the section <Removing the 1. Engage the catch pins on the removal tool 7 and Hard Rubber Frame>. - Page 10 Installing in Japanese-made Cars Installation on Toyota, Nissan or Mitsubishi Car using Brackets at Holes shown by "●" Accessory ! (M5x6mm) or Accessory @ (M5x7mm) Car Bracket Accessory ! (M5x6mm) or Accessory @ (M5x7mm) Screws (included in audio unit package) Screws (included in audio unit package) Audio unit or others...
- Page 11 Installation on Toyota Car using Brackets at Holes shown by "●" When using the bracket shown above, you cannot use screws at two holes of the right and left unit sides. 1. Mount the bracket at each side. Car Bracket Accessory ! (M5x6mm) Accessory ! (M5x6mm) Screws (included in...