Table; Wall; Dial Mode Selection - AT&T 922 User Manual

Table

1 Remove the base.
2 Connect line cord(s) to telep h o n e.
• If you have a two-line jack,
use only the line cord with the
clear modular plugs on each
end. Plug one end into the jack
labeled L1 OR L1/2 on the
bottom of the telephone.
• If you have two separate
jacks, use both line cords.
Insert one end of the cord with
the clear plugs into the jack
labeled L1 OR L1/2 on the bot-
tom of the telephone. Insert one
end of the cord with the blue
plugs into the jack labeled L2
on the bottom of the telephone.
3 Attach the base.
Turn the base so that the larger
end of the base is toward the top
of the telephone. Attach the base
by inserting the tabs into the slots.
Push down on the large end of the
base to lock it into place.
4 Connect the line cord(s) to your
modular jack(s).
• If you have a two-line jack,
plug the free end of the line
cord into a modular baseboard
jack. Make sure the cord snaps
firmly into place.
• If you have two sep a rat e
j a ck s , plug the free end of the
c o rd with the blue plugs into the
modular jack for Line 1. Plug
the free end of the cord with the
clear plugs into the modular
j a ck for Line 2. Make sure the
c o rds snap fi rm ly into place.
5 Connect handset to telephone.
Plug the coiled cord into the hand-
set jack on the side of the phone.
Plug the other end of the coiled
cord into the handset, and then
hang up.
6 Check for dial tone.
Press , lift the handset or
press , and listen for a dial
tone. Then press
cannot hear a dial tone, turn to
"In Case of Difficulty."
I N S TA L L AT I O N
7 Confirm Lines 1 and 2.
Press
telephone numbers. If you hear a
busy signal, Line 1 is the number
you called. If Line 2 rings, it is the
number you called.
1 Remove the base.
2 Connect bundled line cord(s) to
telephone.
Leave the telephone line cord(s)
bundled.
• If you have a two-line wall
jack, use only the line cord
with the clear modular plugs on
each end. Plug one end into the
jack labeled L1 OR L2 on the
bottom of the telephone. Place
the bundled line cord in the
open area under the set.
• If you have two separate wall
jacks, use both line cords.
Leave the cord with the clear
plugs bundled. Plug one end of
this cord into the jack labeled
L1 OR L1/2 on the bottom of
the telephone. Unbundle the
cord with the blue plugs. Plug
one end of this cord into the
jack labeled L1 OR L1/2 on
the bottom of the phone.
Rebundle the cord and store it
in the open area under the set.
3 Attach the base.
Turn the base so that the larger
end of the base is toward the bot-
tom of the telephone. Attach the
base by inserting the tabs into the
slots. Push down on the large end
of the base to lock it into place.
4 Reverse handset tab.
To mount the telephone on a wall,
you must reverse the handset tab.
This tab holds the handset when
you hang up.
Hold down the switchhook, and
slide the tab up and out of its
slot. Turn the tab so that the
curved end is up. Then insert the
. If you
tab back into its slot.
c o n t i n u e d
and call one of your

Wall

2
5 Connect the line cord(s) to
modular wall jack(s) and mount
phone onto wall jack.
• If you have a two-line jack,
plug the free end of the line
cord into a modular wall jack.
Make sure the cord snaps firmly
into place. Place the phone on
the wall jack mounting studs
and pull down until it is held
securely.
• If you have two sep a rat e
j a ck s , plug the free end of the
c o rd with the blue plugs into the
j a ck wh e re you are not mount-
ing the phone (baseb o a rd jack ) .
Plug the free end of the cord
with the clear plugs into the
wall jack. Make sure the cord s
s n ap fi rm ly into place. Place the
phone on the wall jack mount-
ing studs and pull down until it
is held fi rm ly in place.
Follow Steps 5, 6 and 7 under
"Table" Installation.

Dial Mode Selection

This telephone will wo rk with tone or
dial pulse (ro t a ry) serv i c e. Even wh e n
set to dial pulse serv i c e, the phone
can be sw i t ched tempora ri ly to tone,
for access to services that re q u i re
tone signaling, i n cluding some tone-
a c t ivated computer systems.
This product comes set in the TONE
mode. Make sure you choose the cor-
rect dialing method ( TONE/ PULSE);
touch tone dialing will not work if
you have dial pulse service.
After the telephone is plugged in, if
you have dial pulse (rotary) service,
lift handset and press
then press or lift handset
and press , ,
To change back to touch tone service,
press , , ,
To switch from pulse to tone dialing
during a phone call, see "Temporary
Tone Dialing."
or ,
, , .
, .