Calibration Module Flowchart - Edelbrock 3530 Owner's Manual

POWER ON
WEBER/ EDELBROCK
Pro-Flo EFI System
RPM: 3000 FUEL: 4.0 ms
VAC: 12.0Hg SPK: 36
ENTER/EXIT
< FUEL MODIFIERS >
ENTER to select
ENTER/EXIT
FUEL @ WOT 1000: ±0%
EXIT = scroll ENTER
FUEL @ 06" 1000: ± 0%
EXIT = scroll ENTER
FUEL @ 12" 1000: ± 0%
EXIT = scroll ENTER
UP DOWN
FUEL @ 18" 1000: ± 0%
EXIT = scroll ENTER
Transient Fuel: ± 0%
EXIT = scroll ENTER
Cold Start Fuel: ± 0%
EXIT = scroll ENTER
Global Fuel Mod: ± 0%
EXIT = scroll ENTER
UP / DOWN
©2005 Edelbrock Corporation
Rev. 2/05
(1-2 second commercial )
UP
˚
TH20: 180 F TPS: 28
DOW N
˚ ˚
TAIR: 98 F Volt: 14.5
ECU: Q1.3 (c) WEBER ' 93f
CAL: EDEL xxxx CM: 1.6
UP / DOWN
FUEL @ ____ 1000: ±0%
EXIT = scroll ENTER
FUEL @ ____ 2000: ±0%
EXIT = scroll ENTER
ENTER
FUEL @ ____ 3000: ± 0%
EXIT
EXIT = scroll ENTER
UP DOWN
FUEL @ ____ 4000: ± 0%
EXIT = scroll ENTER
FUEL @ ____ 5000: ± 0%
EXIT = scroll ENTER
FUEL @ ____ 7000: ± 0%
EXIT = scroll ENTER
< MISC. MODIFIERS>
ENTER to select
ENTER/EXIT
Target Idle RPM: 950
EXIT = scroll ENTER
Idle Fuel Mod: ± 0%
EXIT = (+) = ( - )
UP DOWN
EXIT
Idle Spark Mod: ± 0
˚
EXIT = scroll ENTER
Idle Spd Actvty: ± 0%
EXIT = (+) = ( - )
Idle Control: OFF
EXIT = scroll ENTER
Closed loop fuel: OFF
EXIT = scroll ENTER
Base Ti m'g set: OFF
EXIT = scroll ENTER
Rev limiter RPM: 6750
EXIT = scroll ENTER
Pro-Flo EFI Installation Instructions
CALIBRA TION MODULE DIAGRAM
˚ UP
Idle: 25% RPM: 3000
˚
DOW N
TPS: 28 Target: 950
(software identification)
< SPARK MODIFIERS >
ENTER to select
ENTER/EXIT
SPRK @ WOT 1000: ±0
EXIT = (+) = ( - )
SPRK @ 9" 1000: ± 0
EXIT = (+) = ( - )
SPRK @ 18" 1000: ± 0
EXIT = (+) =( - )
UP DOWN
Global SPRK Mod: ± 0
EXIT = scroll ENTER
(FROM ANYWHERE IN MENU)
SAVE
SAVE data set: A/B/C
EXIT = scroll ENTER
Saving In progress...
Saved to data set #A
Press EXIT
EXIT
(Return to main menu)
(NOTICE: Some values shown represent arbitrary examples)
(DIAGNOSTIC error messages will flash on any screen)
30
UP
RPM: 3000 – > •••••••••
DOW N
VAC: 12.0 – > ••••
UP / DOWN
UP / DOWN
SPRK @ ____ 1000: ± 0
˚
EXIT = scroll ENTER
ENTER
SPRK @ ____ 1750: ±0
˚
EXIT = scroll ENTER
EXIT
˚ SPRK @ ____ 2500: ±0
EXIT = scroll ENTER
UP DOWN
SPRK @ ____ 3500: ± 0
˚
EXIT = scroll ENTER
SPRK @ ____ 4500: ± 0
EXIT = scroll ENTER
SPRK @ ____ 6000: ± 0
EXIT = scroll ENTER
RESTORE
RESTORE: baseA/B/C
EXIT = scroll ENTER
Restore In progress...
EXIT
Data set #A RESTORED
Press EXIT
EXIT
˚
˚
˚
˚
˚
˚
Brochure #63-0273
Catalog #3530 & #3531