Panamax MOD-AT2 Instructions

INSTRUCTIONS FOR PANAMAX SIGNAL LINE PROTECTION MODULES - PREMIUM SERIES
LINE EQUIP
IN OUT
RJ-45 RJ-45
EQUIP
LINE
LINE OUT
IN
IN RJ-14
RJ-14
S110D
EQUIP
LINE
LINE EQUIP
IN OUT
OUT
IN RJ-11 RJ-11
EQUIP
LINE
OUT
IN
RJ-11
RJ-11
MOD-AT2 MOD-AT4
LINE
EQUIP.
IN OUT
MOD-UTP MOD-CAT5
These modules are approved accessories for use with compatible Panamax AC
base units. Compatible base units include the following:
CURRENT PRODUCTS
AC Base Units
M8HT-PRO
PM8-EX M4-EX
M8-HT
PM8T-EX M4T-EX
PM8-HT
PM8C-EX M8-EX
PM8DBS-EX M8C-EX
When properly installed, the base unit's Connected Equipment Protection Policy
remains valid. All modules include a small rectangular bracket and mounting screws. This
bracket replaces the small triangular wall-mount bracket that comes with the models listed in
the CURRENT PRODUCTS above.
Installation Instructions
1. Mount the rectangular bracket to the back
of the AC base unit with the #8-32 x 5/16"
machine screws.
Note: The brass ground connector must be
used with the bracket in order to bond the
module ground to the base unit's ground.
2. Mount the signal line module to the
bracket (screws provided with the module).
3. Optional – The assembled base unit and
module(s) may be wall mounted if desired.
4. Connect the wiring to the signal line
module as shown in the appropriate follow-
ing section.
All telephone input/output connections will
be labeled with LINE and EQUIP.
EQUIP.
LINE
OUT
IN
It is very important to connect
telephone signal lines properly.
There are no designated
input/output connections
on coaxial protection
modules. These are
bi-directional modules
in both transmission fre-
quency and voltage.
800-472-5555 www.panamax.com
EQUIP LINE
LINE EQUIP
OUT IN
IN OUT
S110D S110D
S110D S110D
MOD-AT8110
LINE
IN
RJ-11
SAT /
CATV
EQUIP
OUT
RJ-11
SAT / SAT /
CATV
CATV
MOD-DBSTV MOD-SPKP
DISCONTINUED PRODUCTS
AC Base Units
M8C-EX
M4
M8
M8DBS-EX
M4T M8T
M8C-Pro
M4L M8C
M8HC-Pro
Module
Ground
Connector
Bracket
Ground
Connector
Ground
Connector
AC Base Unit
An easy access
PULL OUT card
is included on
the back of each
SAT /
module for wiring
CATV
diagrams and
specifications.
Model: MOD-AT2 (Secondary Protector)
LINE EQUIP
IN OUT
RJ-45 RJ-45
EQUIP
LINE
EQUIP
OUT
IN
OUT
RJ-14
RJ-14
S110D
EQUIP
LINE
OUT
IN
RJ-11 RJ-11
EQUIP
LINE
OUT
IN
RJ-11
RJ-11
LINE
IN
MOD-DT4
1 1
2 2
The MOD-AT2 module is designed to protect
3 3
4 4
5 5
standard phone lines connected to computer
6 6
7 7
modems, telephones, pay-per-view ports, etc.
8 8
It will also protect DSL lines (ADSL, G.Lite)
going into the DSL modem. The MOD-AT2
module will protect a single phone line using
an RJ-11 (2 wire) cord or a dual phone line
using an RJ-14 (4 wire) cord.
Model: MOD-AT4 (Secondary Protector)
M8KSU
LINE
M8COM
IN
RJ-45
M8KSU
LINE
LINE
IN
IN
RJ-14
S110D
LINE
IN
RJ-11
LINE
IN
RJ-11
The MOD-AT4 module is designed to pro-
tect standard phone lines and DSL (ADSL,
G.Lite) lines. Multiple input & output jacks
provide complete installation flexibility. The
following diagram shows how the
jacks/wires are interconnected. Different
cables/connections can be split or com-
bined to accommodate a variety of installa-
tions. For example:
• Incoming lines can be punched-down on
the 110 jack on the LINE side and four RJ11
(single-line) cords will connect from the
EQUIP side to the equipment.
Model: MOD-AT8110 (Secondary Protector)
LINE
IN
S110D
L
I
The MOD-AT8110 module is designed to
protect up to 8 standard phone lines using
110 punchdown connectors on both the
input LINE and output EQUIP.
1. Cut the cable from the primary protector
to the correct length and punch down the
1
WIRING DIAGRAM AND SPECIFICATIONS
For Analog Telephone Lines
EQUIP
OUT
• 4 Wires (1 RJ-14) Protected
• 260 Volt Clamping
• Auto-resetting PTC's
1. Connect the telephone line to the LINE
jack on the module.
2. Use a modular cord to connect the
EQUIP modular jack to the equipment to be
protected.
WIRING DIAGRAM AND SPECIFICATIONS
Bl
Or
EQUIP
OUT
Gr
RJ-45
Br
EQUIP
EQUIP
OUT
OUT
RJ-14
S110D
EQUIP
OUT
RJ-11
EQUIP
OUT
RJ-11
• Two RJ14 (dual-line) cords connected to
the LINE side (upper 2 jacks) can be split to
four RJ11 (single-line) cords on the EQUIP
side.
• Four RJ11 (single-line) cords connected
to the LINE side can be combined into a
single RJ45 (8 wire) cord (upper jack) on the
EQUIP side.
Caution: Never install telephones
during a lightning storm.
WIRING DIAGRAM AND SPECIFICATIONS
Blue
Orange
Green
Brown
Blue
EQUIP
OUT
Orange
S110D
Green
Brown
110
IDC
• 16 Wires (two 110 punch-downs) Protected
cable to the LINE IN punchdown block on
the module.
2. Punch down another cable to the EQUIP
OUT punchdown block on the module and
connect to the phone equipment.
MOD-AT2
Bl
Or
Gr
Br
Blue
Orange
Green
Brown
Blue
Orange
Green
Brown
MOD-AT8110
110
For Analog Telephone Lines IDC
• 260 Volt Clamping
• Auto-resetting PTC's