Page 1 Consult the operation manual for proper use of your computer. The product and the accessories are subject to change without prior notice. SHARP assumes no guarantee for results arising from use of pre-installed and third party software. Consult the software vendor for resolution of problems.
Page 2: Notice For Users In The Usa
A shielded I/F cable is required to insure compliance with FCC regulation for Class B computing equipment. ® * As an ENERGY STAR Partner, SHARP has determined that this product meets ® the ENERGY STAR guidelines for energy efficiency. Declaration of Conformity SHARP PERSONAL COMPUTER, PC-MM Series This device complies with part 15 of the FCC rules.
Page 3: Fcc Radiation Exposure Statement
FCC Radiation Exposure Statement The available scientific evidence does not show that any health problems are associated With using low power wireless devices. There is no proof, however, that these low power wireless devices are absolutely safe. Low power Wireless devices emit low levels of radio frequency energy (RF) in the microwave range while being used.
Page 4: Notice For Pc Card Modem
Notice for PC Card Modem FCC Part 15 Subpart B Statement WARNING - FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user’s authority to operate this equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules.
Page 5 The REN is used to determine the quantity of devices which may be connected to the telephone line. Excessive RENs on the telephone line may result in the devices not ringing in response to an incoming call. In most, but not all areas, the sum of the RENs should not exceed five (5.0).
Page 6 For disposal or recycling information, please contact your local authorities or the Electronics Industries Alliance: www.eiae.org Copyright It is the intent of Sharp that this product be used in full compliance with the copyright laws of the United States and that prior permission be obtained from copyright owners whenever necessary.
Page 7 CAUTION: TO PREVENT ELECTRICAL SHOCK, DISCONNECT THE AC ADAPTER AND REMOVE THE BATTERY BEFORE SERVICING. CAUTION: FOR A COMPLETE ELECTRICAL DISCONNECTION, UNPLUG THE POWER CORD AND THE BATTERY. VORSICHT: UM DIE STROMZUFUHR VOLLSTÄNDIG ZU UNTERBRECHEN, DEN NETZSTECKER HERAUSZIEHEN UND DIE BATTERIE ÈNTFERNEN. ATTENTION: POUR UN ARRET TOTAL DU SYSTEME, DECONNECTEZ LA PRISE DE COURANT SECTEUR ET LA BATTERIE.
Page 8: Safety Precautions
Safety Precautions General Follow all cautions and instructions marked on your computer. Except as described elsewhere in this manual, refer all servicing to qualified personnel. Immediately shut off your computer and seek servicing under the following conditions: when the power cord or plug is damaged or frayed when liquid is spilled on your computer when your computer has been dropped or the cabinet has been damaged Location...
Page 9 Never subject your computer to sudden shocks or extreme vibration. Do not drop your computer or hit it with other equipment. Do not scratch the surface of the LCD screen. Turn off your computer and disconnect the AC power cord before cleaning. When carrying your computer: Turn off your computer.
Page 10 Charging Charge the battery pack only with the AC adapter and AC power cord included with your computer. Discharging Do not use the battery pack for any other purpose than powering your computer. Storage Store the battery pack in a cool and dry place. Do not store it at temperatures above 140 F (60 C).
Page 11 During thunder storms, you should turn off your computer, unplug the AC power cord and remove the modem cable from your computer. Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface.
Page 12: Other Precautions
PC Disposal or Transfer Prior to the disposal or transfer of your computer, you should erase the data from hard disks. To remove the data from your hard disk drive, you will need to: “Delete” the data by placing it in your recycle bin. Empty the recycle bin.
Page 13 Your computer is integrated with a magnet on the right side of the display. Be sure to keep magnetic cards and floppy disks away from the right side of your computer to prevent the data on the cards or floppy disks from being erased. Magnet This computer has a sensor on the right side of the keyboard that responds to the magnet.
Page 14: Notice Of Security With Wireless Devices
Use with a clear understanding that wireless LAN includes vulnerabilities that could allow attackers to simply bypass security features. Security measures are important for all users to understand for a safe use of wireless LAN. SHARP encourages all users to configure the security settings with their own judgment and responsibility.
Page 15: About This Manual
Information in this manual is subject to change without notice and does not represent a commitment on the part of SHARP Corporation and its sales subsidiaries. SHARP Corporation and its sales subsidiaries shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from the furnishing, performance, or use of this material.
Page 16: Recording Important Information
Recording Important Information For future reference, please record the following information in the spaces provided below. Model Number: Serial Number: Date of purchase: Dealer’s Name: Place of purchase: Password: The serial number is printed on a sticker located on the bottom of the computer.
Page 17: Manual Conventions
Manual Conventions This manual uses a set of style conventions described below. Notes and Cautions are italicized with icons: A note icon informs you of a special technique or information that may help you perform a task or better understand a process. A caution icon alerts you to something that may cause problems or damage to hardware, software or data.
Page 18: Table Of Contents
Table of Contents Notice for All Users ....................i Notice for Users in the USA..................ii Notice for PC Card Modem..................iv Safety Precautions ....................viii Notice of Security with Wireless Devices.............. xiv About This Manual....................xv Recording Important Information................xvi Manual Conventions....................xvii Table of Contents ....................xiii Overview of Computer...................
Page 19 Peripherals Peripheral Device Connectors................4-1 Optional External Floppy Disk Drive Unit ............4-3 Optional External CD-ROM Drive Unit ..............4-6 Display ......................... 4-11 Audio System ....................... 4-15 USB Device......................4-17 PC Card ........................ 4-18 Printer........................4-21 Communication Functions LAN Unit ....................... 5-1 Wireless LAN......................
Page 20 Appendixes Maintenance and Care ...................A-1 Virus Infection Protection ..................A-3 Data Backup And Restore ..................A-6 Re-installation Instructions..................A-7 Troubleshooting Common Problems ....................T-1 Trouble when Starting ................... T-2 Trouble with Display..................... T-3 Trouble with Keyboard/Glide Pad................. T-4 Trouble with Floppy Disks..................T-4 Trouble with Hard Disk..................
Page 21: Overview Of Computer
Overview of Computer Each number after an arrow indicates the page referring to the part. Actual appearance of your computer may be slightly different depending on the model. Front Wireless LAN Antenna →5-4 LCD Screen →2-8 Power Button →1-5 Mobile Mode Switch →3-12 Keyboard →2-6 Status Indicators...
Page 22 Right AC Adapter Jack→1-4 USB Port LAN Jack →5-2 →4-3,7,16,21 PC Card Slot→4-17 Left Headphone/Audio Output Jack →4-14 USB port→4-3,7,16, 21 Connection Cradle Port →7-5 Rear External Monitor Port →4-12 xxii...
Page 23 Bottom Battery Pack→3-1 Ventilation Reset Switch Openings→ iv →2-3 Speaker xxiii...
Page 24 xxiv...
Page 25: Quick Setup
CHAPTER 1 Quick Setup Your computer is designed and pre-configured for easy setup and use. This chapter describes the steps to set up your computer and operate it as quickly as possible. Read this chapter first. Installing Battery Pack Your computer is powered with either the battery pack or AC power source. See the next chapter for more information on the power sources.
Page 26 Insert the battery pack into your computer by matching the notched parts of the battery to the projected parts of your computer. Projected Part Projected Part Notched Part Notched Part Push the battery pack all the way until you hear the clicking sound.
Page 27 Slide the battery stopper to the locked position ( ). Turn your computer over and go to the next section.
Page 28: Connecting To Ac Power Source
Connecting to AC Power Source Plug the AC adapter cable into the AC adapter jack on the right side of your computer. Plug the AC power cord into the AC adapter. Plug the AC power cord into a wall outlet. AC Adapter Jack AC Adapter AC Power Cord...
Page 29 Steady the base cabinet of your computer with your hand and hold the jutted part with your thumb or finger and then, raise the display. Jutted Part Press the power button to turn on your computer. Power Button Power Indicator Do not touch or operate the keyboard and mouse until Windows completely activates unless you are prompted to do.
Page 30: Setting Up Windows
Setting Up Windows The steps in the setup process are as follows: • Configuring your location, language and keyboard type • Configuring your time zone • Accepting license agreement • Naming your computer • Creating an account • Completing configuration To setup Windows, follow the instructions on the screen.
Page 31 Properties Dialog Box in Windows In this manual, you will often see the expression “XXX Properties dialog box.” A dialog box is a window containing text boxes, check boxes, buttons, etc., with which you can send commands to Windows or other application programs. To open the properties dialog boxes, click start - Control Panel.
Page 32: Turning Off Your Computer
Turning Off Your Computer When you’ve finished using your computer, turn it off with one of the following ways: • From the start menu Click start – Turn Off Computer. In the Turn off computer dialog box, click Turn Off. •...
Page 33: Basic Operations
CHAPTER 2 Basic Operations This chapter describes the basic operations of your computer. Choosing Power Source You can use your computer with one of the following power sources: • AC power from a wall outlet Use AC power whenever possible; rely on the battery only when AC power is not available.
Page 34 • When the battery is hot, the battery indicator may turn off and stay off until the battery becomes cool. • For more information on System standby/hibernate, see Chapter 3. Using AC Adapter When connected to a wall outlet, the AC adapter provides power for operation and charges the battery.
Page 35: Resetting System
Resetting System You may need to restart the system if your computer hangs up or a new hardware or software is installed. When a message appears after the installation, click OK, Yes, etc. to restart Windows. You can also restart Windows by clicking start - Turn Off Computer; then, Restart. Resetting may cause data loss.
Page 36: Using Glide Pad
Using Glide Pad Your computer is equipped with an integrated pointing device called glide pad. Using the glide pad, you can move the pointer, select an item from a menu, and perform other tasks in the same way you would with a mouse. Glide Pad •...
Page 37 Using Glide Pad Take a moment to become familiar with how the glide pad works. Place Your Fingertip Place your left or right hand next to the glide pad, resting your wrist naturally in a relaxed manner. Place your thumb or finger on the glide pad. Move Your Fingertip The rectangular pad of the glide pad is used to move the pointer around the display.
Page 38 Changing Configuration In the Mouse Properties dialog box, you can change the configuration of the glide pad, such as swapping left and right buttons, changing the pointer size, etc. Double- click icon on the taskbar.
Page 39: Using Keyboard
Using Keyboard Your computer, equipped with the Windows Enhanced Keyboard, provides all the functionality of a full-sized desktop keyboard. Special Keys Opens the Windows start menu. This key functions the Windows Key ( same as the start button on the screen. Opens short-cut menus for the specific items.
Page 40: Controlling Volume
Controlling Volume You can adjust the output volume of your computer with the following volume controls which interact with each other. With Keyboard To decrease the output volume, press and hold Fn key and then, press F3 ( ) key. To increase the output volume, press and hold Fn key and then, press F4 ( ) key.
Page 41 If you control: Wave Controlling the volume of CD or WAVE file SW Synth Controlling the volume of MIDI file Any software containing audio function may also have its own volume control. Note that the volume controls discussed on the previous page and the software volume control will interact with each other.
Page 42: Adjusting Display
Adjusting Display You can adjust the brightness, resolution, and number of colors of the internal LCD display for more comfortable viewing. Changing Brightness of Display To decrease the brightness of the internal LCD display, press and hold the Fn key, and then press the F6 ( ) key.
Page 43 • You cannot switch to display resolutions and number of colors that are not available. • In the Color quality, Medium (16 bit) means 65,536 (64K) colors, and Highest (32 bit) means about 16,770,000 (16M) colors. Displaying on Screen Upside Down This feature allows you to show the images on the LCD screen upside down.
Page 44: Sharing Your Computer
Sharing Your Computer If you are sharing your computer with your colleagues or family members, set a user account for each person. Every user can choose their favorite desktop setting, web site lists, or make their own My Documents folder etc., and save them to their user accounts.
Page 45 Select a new account to start Windows XP again. If you cannot see Switch User in Log Off Windows dialog box, click Change the way users log on or off string in User Accounts dialog box, and check Use Fast User Switching and click Apply Options. Setting Password to User Account You can set a password to each user account to avoid unauthorized use of your computer.
Page 46 a limited account, go to the next step. (You cannot change the password of another user account.) Select Change the password string or Change my password string. • If the password has not been set yet, Change the password or Change my password will not appear.
Page 47: Battery And Power Management
CHAPTER 3 Battery and Power Management This chapter explains how to manage your computer’s power effectively and use the battery pack. In this section, you often see the expression “Power Options Properties dialog box”. To open the dialog box: 1. Click start - Control Panel. 2.
Page 48: Checking Battery Level
Charging Battery Pack Connect the AC adapter to your computer. While the battery is being charged, the battery indicator lights orange. When the battery is fully charged, the battery indicator turns green. Charging time may vary according to the status of your computer. •...
Page 49: Low Battery Indication
• The remaining operating time depends on the amount of the power you are consuming. If you are using the audio system, PC card slot, hard disk drive, or peripheral devices with your computer, it may consume more battery power. •...
Page 50 On Windows, you can set the battery level for sounding an alarm and letting your computer go on System standby, System hibernate or shut down afterward. In the Power Options Properties dialog box, select Alarms tab. Set the battery level at which the alarms are activated. We recommend you set Critical battery alarm to 5 % or more and Low battery alarm to more than the value of Critical battery alarm.
Page 51 With the Fn key pressed down, press the F7 key several times so that the screen brightness is maximized. Leave your computer on to discharge the battery pack. When it is completely discharged, the system will automatically shut down. Connect your computer to AC power source and let the battery fully charged again.
Page 52 Changing Battery Pack to Optional High Capacity Battery Pack The capacity of a battery pack gradually decreases when used repeatedly (the deterioration rate depends on the operating environment). If the battery life becomes extremely short even after the conditioning, you should buy an optional high capacity battery pack (CE-BL25).
Page 53 Insert the high capacity battery pack into the computer by matching the notched parts of the battery to the projected parts of the computer. High Capacity Battery Pack (CE-BL25) Notched Part Checking Battery Level of High Capacity Battery Pack Follow the steps in Checking Battery Level in this chapter. Conditioning High Capacity Battery Pack Follow the steps in Conditioning Battery Pack in this chapter.
Page 54: Power Management
Power Management Power management saves electricity and extends battery life by controlling power supply to built-in devices. You can set the following power management properties on Windows. • Stopping power supply to the hard disk • Stopping power supply to the display •...
Page 55 Using System Standby/Hibernate System standby/hibernate is a very useful power management tool. For example, after your computer has entered System standby mode, you can restart your computer more quickly when compared to a restart, after a normal shutdown operation. When your computer resumes from System standby/hibernate, the system restores the exact last state of your computer.
Page 56 Supporting System Hibernate If your battery becomes completely discharged during System standby, you will lose unsaved data and will need to reboot your computer. Therefore, if you are planning to leave your computer powered by battery for long periods of time, we recommend System hibernate. Confirm that System hibernate is supported with the following steps.
Page 57: Disabling Power Management
• You press the power button. The above functions if you perform the following: In the Power Options Properties dialog box, select Advanced tab. Select Hibernate or Stand by in When I press the power button on my computer field. Click OK.
Page 58 Using Mobile Mode Switch Your computer is equipped with the mobile mode switch allowing you to extend battery life. When your computer is in mobile mode, it automatically controls system power consumption: by reducing CPU performance and decreasing screen brightness. The control will make the battery life longer.
Page 59: Peripherals
CHAPTER 4 Peripherals This chapter describes how to use peripheral devices with your computer. You can connect a floppy disk drive unit, an optional CD-ROM drive unit, a printer, an external monitor, an, PC cards, or other devices to your computer. To ensure proper use, be sure to read the instructions for each peripheral device before connecting it to your computer.
Page 60 Peripheral Connection Overview External Monitor Port* USB Port USB Port Headphone/Audio Output Jack *Use the provided display converter cable to connect an external monitor to your computer. Connector Shape Connector name Connector shape USB Port External Monitor Port Headphone/ Audio Output Jack...
Page 61: Optional External Floppy Disk Drive Unit
Optional External Floppy Disk Drive Unit You can use double-density (2DD) 720KB or high-density (2HD) 1.44MB floppy disks with the optional external floppy disk drive unit (CE-FD05). Connecting Optional External Floppy Disk Drive Unit Do not place the floppy disk drive unit on its side or upside down. Do not press on the floppy disk drive unit.
Page 62 Inserting Floppy Disk Hold the floppy disk with the arrow facing up, toward the drive. Slide the disk into the drive until it locks into place. Arrow Facing Up Indicator Always insert a floppy disk straight into the floppy disk drive. When inserting the disk, make sure it is not upside down.
Page 63 Formatting Floppy Disk Make sure the floppy disk is not write-protected, and insert it into the floppy disk drive. Click start - My Computer. Right-click 3 ½ Floppy (A:) icon; then, click Format… from the pop-up menu. Select the appropriate formatting options. Click Start to start formatting.
Page 64: Optional External Cd-Rom Drive Unit
Optional External CD-ROM Drive Unit A compact disc (CD) is a storage medium, with which you can read data, play music, install and run programs, etc. The optional external CD-ROM drive unit (CE-CD05) can be connected to either of the USB ports on your computer. CAUTION FOR LASER Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
Page 65 Connecting Optional External CD-ROM Drive Unit (CE-CD05) Do not place the CD-ROM drive unit on its side or upside down. Do not press on the CD-ROM drive unit. It may damage the drive or cause malfunction. Do not place the AC adapter on the CD-ROM drive unit. It may cause the drive to malfunction.
Page 66 Slide the cover latch to the right and open the cover. Cover Latch Remove the protection sheet before you use the drive for the first time. Protection Sheet Handling CD Do not write on either side of the disk, particularly the non-label side. Data is read from the non-label side.
Page 67 Place your CD onto the disk spindle and press on the center of your CD with label side up, until it locks onto the disk spindle. Close the disk cover. Insert a CD firmly until it is locked onto the spindle; then, close the disk cover, or the disk may fall off the spindle and get damaged.
Page 68 Playing CD With some CD-ROMs, you can hear the sound of them through the audio out jack of the CD-ROM drive unit. Connect headphones or speaker system with an amplifier to the audio out jack. Audio Out Jack Disconnecting Optional External CD-ROM Drive Unit To remove the unit, you need to perform the following steps before you remove it.
Page 69: External Display
External Display You can use an external monitor with your computer. To display the images on both displays simultaneously, use the 1024x768 resolution. Some monitors, which are not compatible with your computer, may not display correctly. In this section, you often see the expression “Display Properties dialog box.”...
Page 70 Connect one end of the display cable to the external monitor port, then, the other end of the display cable to your external monitor. If the display cable has screws, be sure to tighten them. External Monitor Port Display Cable (supplied with the monitor or the one in the market)
Page 71: Display
Switching Display In the Display Properties dialog box, select Settings tab; then, click Advanced button. Select Display tab; then, click the button before the output display you desire and click OK. Monitor means the internal LCD display and Panel means the external display.
Page 72 Displaying Image on LCD and External Monitor When displaying on both of the LCD monitor and the external monitor simultaneously, the external monitor should be capable for displaying in 1024 768 resolution or higher. Otherwise, you may not display images on the external monitor properly.
Page 73: Audio System
Audio System You can output sound to speakers, audio equipment or headphones. Connecting Speaker You can connect stereo speakers with an amplifier to the audio output jack on the left side of your computer Speakers with an Amplifier Headphone/Audio Output Jack Stereo Mini Plug Connecting Audio Equipment You can connect analog audio equipment to the audio output jack on the left side of...
Page 74 Connecting Headphone Use the headphone with an impedance of 8 .or more (32 is recommended.) Headphone Headphone/Audio Output Jack Stereo Mini Plug 4-16...
Page 75: Usb Device
USB Device Your computer has an interface called Universal Serial Bus (USB) and its two USB ports support USB1.1 and USB2.0. With a USB connection, you can connect/disconnect peripherals without turning off your computer. Generally, when you connect a device to your computer, the necessary driver will be installed automatically.
Page 76: Pc Card
PC Card Your computer is equipped with a PC card slot, which can accommodate a Type II card or a CardBus compliant card. You can insert/eject the card without turning off your computer. Before inserting a PC card into the slot, refer to its manual. Inserting PC Card When a new card is correctly inserted, the appropriate driver is automatically installed.
Page 77: Ejecting Pc Card
Insert a PC card into the slot with the label face up until it locks into place. Label Face Up If the dialog box asking you What do you want Windows to do? appears, select the task you want. Ejecting PC Card Some PC cards may become hot after long use.
Page 78 Push the eject button until the inserted PC card pops out; then, remove it. Push the PC card eject button all the way inside the cabinet for safekeeping. 4-20...
Page 79: Communication Functions
CHAPTER 5 Communication Functions This chapter explains how to use the wired LAN unit, the wireless LAN function and the modem card. • When you use communication software: • Connect your computer to the AC power source. • Disable power management. (Refer to Disabling Power Management of Chapter 3.) •...
Page 80 Connecting Your Computer to LAN Turn off your computer. Open the cover for the LAN jack on the right side of your computer. Cover To avoid damaging the LAN unit, close the cover after you finish using the LAN unit. Connect one end of the LAN cable to the LAN jack and the other end to the network hub.
Page 81 Configuring LAN Unit Click start - Control Panel. Click Network and Internet Connections; then, Network Connections. If Classic view is selected, double-click Network Connections icon. Right-click Local Area Connection. From the pop-up menu, click Properties. In the Local Area Connection Properties dialog box, set the network setting according to the instruction of your network administrator.
Page 82 Removing LAN Cable Be sure to push up the locking lever when disconnecting the cable. Excessive force may result in breaking the locking lever. Turn off your computer. Push up the locking lever and hold it, then, remove it straight from the LAN jack. Locking Lever Close the cover for safekeeping.
Page 83: Wireless Lan
Wireless LAN Your computer has an integrated wireless LAN function compliant with IEEE 802.11g and IEEE802.11b standards. You can access a network using the wireless LAN. There are two kinds of wireless networks: a network using an access point and an adhoc network.
Page 84: Security Measures
Security Measures Since wireless LAN provides data transfer using electric waves instead of LAN cables between communicating devices, a third party can illegally access to and monitor the transmitted information. The following security measures reduce opportunities to receive the threats. Use a combination of the following measures for more secure communications.
Page 85 WEP (Wired Equivalent Privacy) Encryption WEP reduces the opportunities for a third party to monitor the information transmitted through wireless LAN network by encrypting the information. To enable the WEP functions, an encryption key or network key must be registered with both communication devices.
Page 86 Click start – Control Panel. Click Network and Internet Connections – Network Connections. If Classic view is selected, double-click Network Connections. Select Wireless Network Connection; then, click Change settings of this connection of Network Tasks. Double-click Internet Protocol (TCP/IP) in This connection uses the following items.
Page 87 Confirm the checkbox of Enable IEEE 802.1x authentication for this network is cleared. Be sure to clear the box for normal use. To enable the IEEE 802.1x in the network, the corresponding settings are required. Consult your network administrator for more information. Click Connect button.
Page 88 In Internet Protocol (TCP/IP) Properties dialog box, select Use the following IP address and set a unique IP address to 192.168.1.2 through 192.168.1.254 and the Subnet mask to 255.255.255.0; then, click OK. • The IP address of each computer should be unique. •...
Page 89 • Be sure to match the key index between your computer and the network/the other computer. Note that some access points and computers have the key index options 0 through 3. Refer to the table below for matching. Access Point 1 Access Point Your /Computer 1...
Page 90: Network Setup Utility
To set your specific network settings, confirm that your computer is connected into the network and has the proper settings for your current environment and follow the instructions below. Click start – All Programs – SHARP Network Setup Utility – SHARP Network Setup Utility. Click OK.
Page 91 not be able to switch to the network properly. In this case, you may need to reconfigure the settings. Changing Network Settings To change the loaded network settings, right-click on the icon you want to change the settings in the Network Setup Utility window and click Edit settings in the pop-up menu.
Page 92: Modem Card
Modem Card Your computer comes with the modem card. In order to use the modem on your computer, install the supplied modem card in your computer. • The modem in your computer is designed only for regular analog telephone lines. The modem may be damaged when connected to a digital ISDN terminal or a digital PBX.
Page 93: Modem Configuration
Configuring Modem Configure your modem making the necessary adjustments as shown below. Modem Configuration When you use the modem first time, you must type your location’s information. Click start - Control Panel - Printers and Other Hardware; then, Phone and Modem Options.
Page 94 5-16...
Page 95: Setup Utility
CHAPTER 6 Setup Utility This chapter describes how to run the Setup Utility to change settings on your computer. Running Setup Utility With the Setup Utility, you can customize the system configuration information, such as time and date, port assignments, or passwords. The information you have specified is saved in a special area called CMOS RAM, which the system reads every time you turn on your computer.
Page 96 Entering and Exiting Setup Utility Turn on your computer. When Press F2 for System Utilities appears, press F2. Change to the desired settings. Refer to the next section. Select Exit menu. Select one of the exit methods and press Enter. Confirm the message and press Enter again.
Page 97: Main Menu
Quick Boot defines whether the system simplifies the internal check while booting, to shorten the boot time. Quiet Boot defines whether the SHARP logo appears on the screen while booting. CPU Information shows the information on the CPU. System Memory shows the volume of the conventional memory used in MS-DOS.
Page 98: Advanced Menu
Advanced Menu Internal Pointing Device enables or disables the built-in glide pad. Resolution Expansion defines whether the Setup Utility screen is expanded when the resolution is 640x480 or 800x600. Enabled means that the screen is expanded. Plug&Play O/S normally has to be as default “Yes”. Max ACPI C-State normally has to be as default “C4 State”.
Page 99 If you enter a wrong password three times, the message System Disabled appears. Press the power button to shut down your computer, and after 10 seconds, press the power button to turn it on again. Your computer supports two different levels of password security: Supervisor password and User password.
Page 100: Boot Menu
Without typing any characters, press Enter. Press Enter twice. Select Exit menu and confirm Exit Saving Changes is highlighted; then press Enter Confirm Yes is highlighted and press Enter. The system restarts. Boot Menu Boot Sequence specifies where the system boots from. Press Enter to open the sub menu.
Page 101: Connection Cradle
CHAPTER 7 Connection Cradle This chapter describes how to use the connection cradle with your computer (hereafter called MM series). Using the connection cradle, you can connect the MM series to another computer (hereafter called host computer). • Never insert anything but the MM series into the connection cradle. •...
Page 102 Installing Application Program You cannot install an application program to the MM series from the host computer when the MM series is inserted in the cradle. In order to install an application program into the MM series, do either of the following performance: •...
Page 103: Overview Of Connection Cradle
Overview of Connection Cradle Front Panel READY Lamp Hard Disk Lamp Battery Indicator DirectHD READ Y Connection Switch D ir e c tH D Rear Panel USB Port AC Adapter Jack...
Page 104 Charging Battery Pack Using Connection Cradle Place the connection cradle on a stable and even work surface. Connect the AC power cord to the AC adapter (1). Plug the AC adapter cable to the AC adapter jack on the rear side of the connection cradle (2).
Page 105 Insert the MM series into the connection cradle with its left side downward until the MM series firmly secured to the connection cradle. Charging will start. Battery Indicators Cradle Front When the MM series and the connection cradle are properly connected, their both battery indicators will light and charging will be started.
Page 106: Connecting To Host Computer
Connecting to Host Computer Using MM Series as External Hard Disk Using the connection cradle allows you to use the MM series as an external hard disk of your host computer. You can read and modify the data on the MM series and also store the data into the MM series, which is powered off, without any media or LAN function.
Page 107 Limitation You cannot use the MM series as an external hard disk when it is powered on or in the system standby/hibernate state. When the Host Computer is Windows XP Log on to the computer as a member of the Computer administrators group. You might not install application programs when you log on to the computer with a limited account.
Page 108 2. Turn off the MM series. You cannot connect the MM series to the host computer when the MM series is powered on or in the standby/hibernate mode. 3. Connect the AC adapter to the connection cradle and insert the MM series into the connection cradle.
Page 109 Slide the DirectHD connection switch on the connection cradle to the ON position. The READY indicator on the connection cradle will be turned green. • When you connect the connection cradle to the host computer for the first time, necessary drivers are automatically installed. Wait until installation process completes.
Page 110 • The drive names such as (E:) and (F:) differs depending on the environment of the host computer. • If you set a user password to the MM series in the Setup Utility, the MM series is shown not as hard disk drive, but as removable disk drive with the icon representing the MM series inserted in the connection cradle with the key mark.
Page 111: Synchronizing Mm Series With Host Computer
Synchronizing MM series with Host Computer You can synchronize files or folders on your MM series and on your host computer. You need to install the SharpSync application (stored on the provided Product Recovery CD-ROM Disk3) onto your host computer for synchronizing. During data communication, set the time of the MM series and the host computer synchronized.
Page 112 Select a destination drive of your MM series for the synchronization and then click Next. Follow the on-screen instructions. After completing the installation of the SharpSync application, ISYNC folder, autozip.run, Autozip.bak and setup.exe may be automatically installed in the destination drive of your MM series. Do not delete the folder and files in order to keep SharpSync software working.
Page 113 Stopping Synchronization You can stop the synchronization between your MM series and host computer without deleting the Sync set. Confirm that your MM series is connected with your host computer and the DirectHD status indicator is lit. Double-click the SharpSync icon on your host computer’s desktop. Select a desired Sync set.
Page 114: Stopping Connection From Host Computer
Stopping Connection from Host Computer You can stop the connection from the host computer while keeping the MM series inserted in the connection cradle, by first stopping the device on the host computer then sliding the DirectHD connection switch of the connection cradle to OFF. Be sure to stop the device before sliding the switch on the connection cradle to OFF.
Page 115: Removing From Connection Cradle
Connecting to Host Computer Again While you keep the MM series inserted in the connection cradle, slide the connection switch back to ON to connect to the host computer again. When you do not remove the MM series from the connection cradle after stopping the device, the connection is stopped, although the READY indicator is on.
Page 116: Setting Password
Setting Password You can set a “user password” to your computer to avoid unauthorized use of the hard disk of the MM series when it is connected to the host computer using the connection cradle. Set the Supervisor Password and User Password in the Setup Utility. Setting Password Set a user password of the MM series in the Setup Utility.
Page 117 Deleting Password On Windows XP or Windows 2000 When the host computer is Windows XP or Windows 2000, delete the password set to the MM series in the Setup Utility. For details, see Security Menu in Chapter 6. On Windows Me When the host computer is Windows Me, cancel the password set to the host computer, before deleting the user password in the Setup Utility of the MM series.
Page 118 7-18...
Page 119: Appendixes
Appendixes The appendixes contain additional information on the use and care of your computer. Maintenance and Care This appendix provides you with information on how to maintain your computer in excellent working condition. Cleaning Your Computer Cabinet Apply a small amount of mild cleaning solution to a dry, lint-free cloth and wipe the cabinet with the cloth.
Page 120 • Do not carry your computer powered on. This may result in loss of data and/or damage to the hard disk drive. • Make sure the display cover is closed before traveling. Otherwise, the cover may be opened unawares, and the display or the keyboard will be damaged. •...
Page 121: Virus Infection Protection
Virus Infection Protection Computer viruses are referred to a kind of maligned programs intentionally engineered. When your computer is infected, several damages would be generated; data in the hard disk may be destructed; your computer may be provided external operation by unauthorized users; you may inadvertently attach infected files to your e-mails resulting in spreading the viruses, for example.
Page 122 When virus infections occur Eliminate the virus by means of the latest anti-virus software or programming software. When it fails, reinstall all the hard disks. (For reinstalling the hard disks, refer to Appendixes.) Protecting Your Computer Against Virus Norton AntiVirus software is prepared for installation into your computer for detecting and eliminating viruses.
Page 123 Norton AntiVirus Update Service Norton AntiVirus software scans for virus by means of a virus definition file allowing the software to identify and block a particular virus. To protect your computer against new viruses, the virus definitions and application need to be kept current. The software automatically checks the web and updates the definition file when needed.
Page 124: Data Backup And Restore
Data Backup and Restore Your important data such as e-mails or files is stored on the hard disk of your computer. Backing up the data in another place is one of the ways that protect your data against any disaster, data corruption or data erase, for example. Backing Up Your Data The File and Settings Transfer Wizard can help you to back up several files and settings at one time.
Page 125: Re-Installation Instructions
Re-installation Instructions To recover your hard disk, you will use PowerQuest®EasyRestore™. Before starting re- installation, read the following End User License Agreement first. PowerQuest(R) EasyRestore (TM) End User License Agreement IMPORTANT: Read this before using your copy of PowerQuest software. This document is a legal agreement between you, the "end user,"...
Page 126 the Commercial Computer Software-Restricted Rights at 48 CFR 52.227-19, as applicable. Contractor/manufacturer is PowerQuest Corporation/P.O. Box 1911/Orem, UT 84059. 6. NO WARRANTY. The Software is being provided to you AS IS. PowerQuest does not warrant the Software to end users. If the Software fails to perform substantially in accordance with the documentation provided to your hardware supplier, PowerQuest will repair or replace the copy of the Software provided to your hardware supplier and will authorize your hardware supplier to provide such repaired or replaced Software to you without charge.
Page 127: Backing Up Data
Preparation For Re-installation You can format the hard disk and re- install the preinstalled software with the recovery CD-ROMs, and set the status of your computer to the same configuration as you used for the first time. The following items are necessary for re-installation: •...
Page 128 Formatting Drives and Re-installing Windows 1. Make sure the computer is turned off. 2. If any peripheral devices are connected to your computer, disconnect them except the external CD-ROM drive unit. 3. Connect the AC adapter; then, turn on the computer. Be sure to connect the AC adapter.
Page 129 16. Set back the appropriate value for each Setup setting. 17. In the Exit menu, confirm Exit Saving Changes is highlighted and press Enter twice. The system will restart. 18. Set up Windows, following the instructions on the screen. When you finish the Setup, the recovery is completed.
Page 130 A-12...
Page 131: Troubleshooting
Troubleshooting This chapter describes how to troubleshoot computer problems. Common Problems Problems with your computer can be caused by something as minor as an unplugged power cord or as major as a damaged hard disk drive. The information in this troubleshooting section is designed to help you find and solve minor problems.
Page 132: Trouble When Starting
Trouble when Starting Why doesn't the power indicator or the battery indicator turn on? • Make sure the AC adapter is correctly connected to the AC adapter jack of your computer. • Make sure the AC power cable is correctly connected to a live wall outlet. Connect another electric equipment to the wall outlet and check whether it is live or not.
Page 133: Trouble With Display
Trouble with Display See the Display section of Chapter 2 and 4. Why is the screen blank? • Press any key to see if any power management feature has turned off the screen to save power. • See the power indicator to check whether your computer is turned on. •...
Page 134: Trouble With Keyboard/Glide Pad
• When you select Resolution Expansion mode, Fn+F5 key combination does not work. Why is the screen blank in a moment? • When you connect/disconnect the AC adapter, your computer, with the POWERPLAY function enabled, controls the power supply. The control causes the screen to be blank.
Page 135: Trouble With Floppy Disks
Trouble with Floppy Disks Why can't I use a floppy disk? • Confirm the optional external floppy disk drive unit is correctly connected. • Confirm the floppy disk is inserted correctly. • Confirm the drive or file name is correct. •...
Page 136 • Confirm the network configuration is appropriate. • Confirm the user name or password is correct. • Confirm the COM port in the communication software is set appropriately. • Turn off the power management in the Windows. • If an unusual device is attached to the line you are connecting to, the modem may not function properly.
Page 137 Why can't I detect the access point on my computer? (for wireless LAN communication) • Confirm the access point is powered on. • Confirm the wireless LAN antenna is enabled. When the antenna indicator lights green, the antenna is enabled. If not, press Fn+F1 keys. •...
Page 138 in Wireless Network Connection dialog box. (Refer to WEP (Wired Equivalent Privacy) Encryption of Chapter 5.) Why can't I communicate with other computers through a wireless LAN? • Confirm the wireless LAN antenna is enabled. When the antenna indicator lights green, the antennas are enabled.
Page 139: Trouble With Peripherals
Trouble with Peripherals Why don't peripheral devices function correctly? • Confirm they are correctly connected to your computer. • Confirm they are Windows XP compliant. • Confirm drivers necessary for the devices are installed. • Set System standby and System hibernates to Never in Power Options Properties dialog box.
Page 140: Trouble With Connection Cradle
Trouble with Connection Cradle Why doesn't the battery indicator on the MM series inserted in the connection cradle turn on? • Make sure the AC adapter is correctly connected to the AC adapter jack of the connection cradle. • Make sure the AC power cable is correctly connected to a live wall outlet. Connect another electric equipment to the wall outlet and check whether it is live or not.
Page 141: Other Troubles
• Make sure that the operating system of the host computer is Windows XP, Windows 2000, or Windows Me. • Slide the connection switch to OFF and then back to ON. You may not have stopped the connection properly. Why is the MM series recognized as removable disk, or why can’t I access to the MM series from the host PC? •...
Page 142 Why can't I use a hardware device? • Make sure the hardware device is not crossed out with an X mark using the following procedure. Click start– Control Panel. Click Performance and Maintenance; then, System. If Classic view is selected, double-click System icon.
Page 143: Index
Index password, 7-18 precautions, 7-1 removing, 7-17 stopping connection,7-15 AC adapter using as external hard disk,7-6 connecting, 1-4 Synchronizing, 7-11 using, 2-2 troubleshooting, T-10 Account creating, 2-12 switching, 2-12 Antenna, 5-4 Audio controlling output volume, 2-6 Display changing brightness, 2-10 Back up data, A-5 changing resolution, 2-10 Battery pack...
Page 144 Glide pad changing configuration, 2-6 clicking and double-clicking, 2-5 drag and drop, 2-5 Network Setup Utility scroll, 2-5 changing, 5-13 troubleshooting, T-4 deleting, 5-13 loading, 5-12 switching, 5-12 Hard disk drive troubleshooting, T-5 Passwords Indicators changing, 2-13, 6-5 antenna,5-4 deleting, 2-14, 6-5 power,1-5, 2-1 setting, 2-13, 6-5 battery status, 2-1,3-3...
Page 145 reset switch, 2-3 Restore data, A-5 Re-installation, A-7 Virus protection, A-3 Wallpaper, 2-11 Wireless LAN Screen Saver, 2-11 activating antenna, 2-7, 5-5 Setup utility communicating, 5-9 advanced menu, 6-4 confirming status,5-9 boot menu, 6-6 connecting to WEP network, 5-7 Changing setting,6-2 connecting to access point, 5-7 entering and exiting, 6-2 troubleshooting, T-6...
Page 146 Index-2...

This manual is also suitable for:

Pc-mm series

Sharp PCMM20 User Manual

Quick Links

Related Manuals for Sharp PCMM20

Summary of Contents for Sharp PCMM20

This manual is also suitable for:

Table of Contents