Switching The Speaker System; Using The Multi-Zone Controls - Pioneer VSX-9040TXH - 110 Watt x 7 Direct Energy Amplification Receiver Operating Instructions Manual

Using other functions

Switching the speaker system

If you selected Speaker B in Surround back speaker
setting on page 91, three speaker system settings are
possible using SPEAKERS. If you selected Normal, Front
Bi-Amp or ZONE 2, the button will simply switch your
main speaker system on or off. The options below are for
the Speaker B setting only.
PQLS HDMI PRESET
STANDARD MULTI-ZONE
SURROUND HOME THX SPEAKERS CONTROL ON / OFF
• Use SPEAKERS on the front panel to select a
speaker system setting.
As mentioned above, if you have selected Normal, the
button will simply switch your main speaker system (A)
on or off.
Press repeatedly to choose a speaker system option:
• SPA – Sound is output from speaker system A and
the same signal is output from the pre-out terminals.
• SPB – Sound is output from the two speakers
connected to speaker system B. Multichannel
sources will not be heard. The same signal is output
from the surround back channel pre-out terminals.
• SPAB – Sound is output from speaker system A (up
to 5 channels, depending on the source), the two
speakers in speaker system B, and the subwoofer.
The sound from speaker system B will be the same as
the sound from speaker system A (multichannel
sources will be downmixed to 2 channels).
• SP (off) – No sound is output from the speakers. The
same sound is output from the pre-out terminals
(including from your subwoofer, if connected) as
when selecting speaker system A (above).
Note
1 • The subwoofer output depends on the settings you made in Manual speaker setup on page 90. However, if SPB is selected above, no sound
is heard from the subwoofer (the LFE channel is not downmixed).
• Depending on the settings in Surround back speaker setting on page 91 output from the surround back pre-out terminals may change.
• All speaker systems (except Speaker B connections) are switched off when headphones are connected.
2 If the receiver is in standby, the display is dimmed, and ZONE and your selected sub zone(s) continue to show in the display.
3 The tuner cannot be tuned to more than one station at a time. Therefore, changing the station in one zone also changes the station in the other
zone. Please be careful not to change stations when recording a radio broadcast.
1
VSX-9140TXH
AUDIO/VIDEO MULTI-CHANNEL RECEIVER
ENTER
PRESET TUNER EDIT
MASTER
VOLUME
PUSH
OPEN
VSX-9140TXH

Using the MULTI-ZONE controls

The following steps use the front panel controls to adjust
the sub zone volume and select sources. See MULTI-
ZONE remote controls on page 70.
STANDBY/ON
BAND TUNE PQLS HDMI
INPUT MULTI-ZONE
CONTROL
SELECTOR SPEAKERS
PHONES
1 Press MULTI-ZONE ON/OFF on the front panel.
Each press selects a MULTI-ZONE option:
• ZONE 2 ON – Selects your primary (ZONE 2) sub zone
• VSX-9140TXH only: ZONE 2&3 ON – Select both sub
zones
• VSX-9140TXH only: ZONE 3 ON – Selects your
secondary (ZONE 3) sub zone
• MULTI ZONE OFF – Switches the MULTI-ZONE
feature off
The MULTI-ZONE indicator lights when the MULTI-ZONE
control has been switched ON.
2 Press MULTI-ZONE CONTROL on the front panel to
select the sub zone(s) you want.
VSX-9140TXH only: If you selected ZONE 2&3 ON above,
you can toggle between ZONE 2 and ZONE 3.
• When the receiver is on,
operations for the sub zone are done while ZONE and
your selected sub zone(s) show in the display. If this
is not showing, the front panel controls affect the
main zone only.
3 Use the INPUT SELECTOR dial to select the source
for the zone you have selected.
For example, ZONE 2 CD-R sends the source connected
to the CD-R inputs to the primary (ZONE 2) sub room.
• If you select TUNER, you can use the tuner controls
to select a preset station (see Saving station presets
on page 51 if you're unsure how to do this).
AUDIO/VIDEO MULTI-CHANNEL RECEIVER VSX-9140TXH
ENTER
PRESET PRESET TUNER EDIT
MASTER
ON / OFF
VOLUME
PUSH
OPEN
VSX-9140TXH
2
make sure that any
3
08
69
En