Page of 2

HP AD510A - StorageWorks Modular Smart Array 1500 cs 2U Fibre Channel SAN Attach Controller Shelf Hard Drive Replacement Instructions

Hp storageworks msa1500 cs scsi i/o module replacement instructions (april 2004).
Hide thumbs
   
hp StorageWorks
MSA1500 cs SCSI I/O
Module
These instructions apply to the MSA1500 cs
product family. The part may also be used
in other HP products. Please refer to
documentation for your specific product for
detailed replacement instructions.
If the product in which this part is being replaced is still under HP
warranty, then the replacement part(s) referred to in these Replacement
Instructions is provided under the terms and conditions of the
Hewlett-Packard Company Limited Warranty for that product. A copy of
this Limited Warranty may be viewed at:
http://h18006.www1.hp.com/products/storageworks/warranty.html
If this is a trade sale part (product out of warranty), then the replacement
part(s) referred to in these Replacement Instructions is provided under HP's
express limited warranty statement, which may be viewed at:
http://customerops.corp.hp.com/1sw/pdm_om/warranty_support/policies/
2330100.doc
The replacement part takes on either the Limited Warranty Period of the
part being replaced or a ninety-day period that begins upon installation
of the replacement part, whichever is greater.
The information contained on these replacement instructions is subject to
change without notice. The only warranty for this replacement product is
as noted above. Nothing in these replacement instructions should be
construed as constituting an additional warranty. The information
provided in these replacement instructions is provided "AS IS" and HP is
not liable for technical or editorial errors or omissions contained herein.
© Copyright 2004 Hewlett-Packard Development Company, L.P.
Please note that this document is protected by federal copyright law and
that no part of this document may be copied, reproduced or translated
without the prior written consent of Hewlett-Packard Development
Company, L.P.
Printed in Singapore.
MSA1500 cs SCSI I/O Module Replacement Instructions
First Edition (April 2004)
Part Number: 361700-001
Replacement
Instructions
361700- 001
About this document
This document details the procedures for replacing a failed
MSA1500 cs SCSI I/O module in HP StorageWorks Modular
Smart Array (MSA) storage systems.
Before replacing the SCSI I/O module, use the following
methods to verify the component failure.
Check the controller LCD for one of the error messages
listed in Table 1.
Table 1: LCD Error Messages
No.
23
SCSI SUBSYSTEM HARDWARE FAILURE
412
STORAGE BOX # EMU NOT RESPONDING
The status LED on the rear of the module is not illuminated
or is flashing amber 1.
1
Figure 1: Status LED
Read the following cautions and information before beginning
removal and replacement procedures.
Caution:
Be sure the replacement part is available before
removing the failed component. Removing a component
impacts cooling within the enclosure.
Caution:
Parts can be damaged by electrostatic discharge.
Use proper anti-static protection. Refer to the
documentation that shipped with your system for additional
information.
Caution:
It is important to follow these instructions when
replacing components in the MSA. If the procedure is done
improperly, it is possible to lose data or damage
equipment.
Before replacing this hot-pluggable component
Caution:
ensure that steps have been taken to prevent loss of data.
Message

Advertising

   Related Manuals for HP AD510A - StorageWorks Modular Smart Array 1500 cs 2U Fibre Channel SAN Attach Controller Shelf Hard Drive

   Summary of Contents for HP AD510A - StorageWorks Modular Smart Array 1500 cs 2U Fibre Channel SAN Attach Controller Shelf Hard Drive

  • Page 1: Verifying Component Failure, Before You Begin

    Replacement Instructions is provided under the terms and conditions of the Hewlett-Packard Company Limited Warranty for that product. A copy of this Limited Warranty may be viewed at: Figure 1: Status LED http://h18006.www1.hp.com/products/storageworks/warranty.html...

  • Page 2

    Step 1: Removing the module Returning the failed component Please follow the return instructions provided in the Note: Before removing the SCSI I/O module, label all cables. This replacement component package. ensures their reconnection in the correct configuration. Additional information For additional information, refer to the MSA technical 1.

Comments to this Manuals

Symbols: 0
Latest comments: