Page of 5

HP AD510A - StorageWorks Modular Smart Array 1500 cs 2U Fibre Channel SAN Attach Controller Shelf Hard Drive Replacement Instructions

Hp storageworks 1500/1510i modular smart array chassis replacement instructions (364862-002, december 2006).
Hide thumbs
   
HP StorageWorks
1500/1510i Modular Smart
Array chassis replacement
instructions
© Copyright 2004–2006 Hewlett-Packard Development Company,
L.P.
Second edition (December 2006)
The information in this document is subject to change without
notice.
Printed in Singapore.
www.hp.com
364862-002
About this document
This document details procedures for replacing a failed MSA1500
or MSA1510i chassis. When replacing a chassis, components are
removed from the failed chassis and then installed in the replacement.
Components that are moved include the following:
Fibre Channel (or Ethernet) I/O modules
Fan modules
SCSI I/O modules
Power supply modules
Controllers
Blanks
NOTE:
The MSA1500 connects to the SAN with a Fibre Channel I/O
module and the MSA1510i connects to the network with a 2–Port
Ethernet I/O module. Illustrations in this document show the Fibre
Channel I/O module of an MSA1500. If you are replacing an
MSA1510i chassis, your module will look different.
Read the following cautions and notices before replacing the chassis.
CAUTION:
Parts can be damaged by electrostatic discharge. Use proper
anti-static protection. For additional information, see the
documentation that shipped with your system.
CAUTION:
Be sure to follow these instructions carefully. If the procedures are
done improperly or out of sequence, it is possible to lose data
or damage equipment.
IMPORTANT:
Schedule a maintenance window of approximately 60 minutes to
complete this procedure.
IMPORTANT:
Before beginning these procedures, verify that there is a known,
good backup of the system. Backup all volumes and, for the
MSA1510i, record the iSCSI and Management settings.
TIP:
Before beginning these procedures, label all cables. This ensures
that they are reconnected correctly.
Page 1

Advertising

   Related Manuals for HP AD510A - StorageWorks Modular Smart Array 1500 cs 2U Fibre Channel SAN Attach Controller Shelf Hard Drive

   Summary of Contents for HP AD510A - StorageWorks Modular Smart Array 1500 cs 2U Fibre Channel SAN Attach Controller Shelf Hard Drive

  • Page 1: Before You Begin

    Parts can be damaged by electrostatic discharge. Use proper anti-static protection. For additional information, see the documentation that shipped with your system. © Copyright 2004–2006 Hewlett-Packard Development Company, CAUTION: L.P. Be sure to follow these instructions carefully. If the procedures are...

  • Page 2

    Remove the SCSI I/O modules Removing the failed chassis Lift the port-colored latch and pull the module out of the chassis. Prepare for the replacement If the MSA is operational, stop all access to the MSA. Press and hold the power on/standby button for five seconds to place the MSA in standby.

  • Page 3

    Remove the MSA from the rack Install the MSA in the rack Remove the decorative bezel from the front of the MSA by grasping Slide the MSA into the rack, and then secure the MSA to the front of the rack, using the thumbscrews on the front of the MSA. the outside edges and pulling with sufficient force to disengage the retaining clips.

  • Page 4: Verifying Proper Operation

    Install the SCSI I/O modules Completing the replacement Slide the module into the chassis SCSI I/O slot until the latch clicks into place. Reconnect the AC power cords to the MSA. Reconnect the SCSI and Fibre Channel (or Ethernet) cables to the MSA chassis.

  • Page 5

    Returning the failed chassis In the materials shipped with the replacement, HP specifies whether the defective component must be returned to HP. In cases where it is required, you must ship the defective part back to HP within a defined period of time, normally five business days.

Comments to this Manuals

Symbols: 0
Latest comments: