Related Manuals for QUAD CONCOURSE Q - MANUAL 2 - REV 1
Summary of Contents for QUAD CONCOURSE Q - MANUAL 2 - REV 1
- Page 1 C O N C O U R S E Q S E R I E S INSTRUCTION BOOKLET MODELS Q6A & Q8A F O R T H E C L O S E S T A P P R O A C H T O T H E O R I G I N A L S O U N D...
-
Page 2: Table Of Contents
Unbalanced Connections ............. 0 8 AND ASSISTANCE. CE Compliance: Statement ................... 0 9 Limited Liability Specifications ................ 1 0 QUAD Industrial assumes no liability whatsoever for any damage or loss, either direct or consequential arising from the installation and use of these Contact Information: products. Liability is limited to replacement of product or refund, at the QUAD Industrial Contact Information ......BACK COVER QUAD Industrial’s discretion. Your rights to compensation may vary by ter- ritory; consult with your local QUAD Industrial office or distributor. Warranty & Service These products are designed to be used as specified, and are warranted to be free from defects in materials or workmanship. Warranty terms and con- ditions vary by territory. Please contact your local QUAD Industrial sales office or distributor for complete details. Under no circumstances should you attempt to repair these products. Doing so may limit or void warranty coverage. -
Page 3: Product Descriptions
P R O DU CT DE S CR IP T IO N correct voltage is selected before powering up this unit. Please check with your QUAD Industrial sales office or local distributor to The Concourse Q6A and Q8A are Active two-way high ensure you have the correct version. -
Page 4: Back Panel
Q6A and Q8A models include a switchable voltage power sup- Seismic Restraint Point ply that accepts either 110-120VAC or 220-240VAC line power. Selection is made through the two-position Voltage Select Switch on the rear panel. In addition there is an IEC AC Input socket and two position rocker Power Switch. -
Page 5: Accessories
A complete installation kit designed to work with the supplied mounting brackets is included with each model and consists of: 1. Seismic restraint tethers (2) 2. Bracket mounting screws (8) 3. Lock washers (2) 4. Nylon locking nuts (2) 5. Friction pads (2) 6. -
Page 6: Installation
IN STAL L AT IO N STEP 1b Step 1 – Install bracket A to wall using suitable fasteners. Step 1a – Remove four screws holding cover plate (2) on rear of speaker. Step 1b – Mount the bracket with the threaded bolt to the cabinet using the four screws removed in step 1 (4). - Page 7 STEP 4 FINISH STEP 5 STEP 6...
-
Page 8: Connections: Connections & Operations
CO N NE CT IO NS & O P E R AT I O N However this configuration will present the signal source with a lower impedance than it would typically drive and may cause CAUTION: Before connecting this unit to the AC power supply added distortion or even damage to the source outputs. -
Page 9: Ce Compliance: Statement
Refer all service and repair to the nearest authorized QUAD Industrial service center or directly to the QUAD Industrial distributors sales office in your region. -
Page 10: Specifications
S PE C IF ICATI ON S Power Amplifier QSUB QSUBA 2x125W/2x 250W/2x500W Amp Power: 300W Watts RMS: Switchable 110-120 Switchable 110-120 110-120 AC Power: 220-240 220-240 Two versions 50Hz−20kHz 50Hz−20kHz 35Hz−420kHz 35Hz−250kHz Frequency Response: (-10dB) 70Hz−17kHz 80Hz−16kHz 42Hz−350kHz 38Hz−225kHz Frequency Response: (+/-3dB) Sensitivity (@2.83V):... - Page 12 F O R T H E C L O S E S T A P P R O A C H T O T H E O R I G I N A L S O U N D © 2006 QUAD Industrial. QUAD Industrial is a member of the International Audio Group. IAG America Inc. 8440 154th Avenue NE · Redmond, WA 98052...
Need help?
Do you have a question about the CONCOURSE Q - MANUAL 2 - REV 1 and is the answer not in the manual?
Questions and answers