Related Manuals for Lenovo 0809B3U
Summary of Contents for Lenovo 0809B3U
- Page 1 ThinkCentre User Guide Machine Types: 0804, 0809, 0811, 0822, 0825, 0828, 0830, 0833, 0837, 0843, 0845, 0847, and 0849...
- Page 3 ThinkCentre User Guide...
- Page 4 First Edition (August 2010) © Copyright Lenovo 2010. LENOVO products, data, computer software, and services have been developed exclusively at private expense and are sold to governmental entities as commercial items as defined by 48 C.F.R. 2.101 with limited and restricted rights to use, reproduction and disclosure.
-
Page 5: Table Of Contents
Replacing the heat sink and fan assembly . . 24 Diagnostic programs . . 66 Replacing the microprocessor . . 27 Lenovo ThinkVantage Toolbox . . 66 Replacing the power supply assembly . 30 PC-Doctor for Rescue and Recovery . . 66 Replacing the optical drive . - Page 6 European conformance CE mark . . 76 Index ....77 Trademarks . . 76 User Guide...
-
Page 7: Important Safety Information
If you no longer have a copy of the ThinkCentre Safety and Warranty Guide, you can ® obtain a Portable Document Format (PDF) version from the Lenovo Support Web site at: http://www.lenovo.com/support... - Page 8 User Guide...
-
Page 9: Chapter 1. Product Overview
DIMMs) Internal drives v Card reader (available in some models) v Optical drive v Serial Advanced Technology Attachment (SATA) hard disk drive Video subsystem v Integrated graphics card functioning through a Video Graphics Array (VGA) connector © Copyright Lenovo 2010... - Page 10 v Peripheral Component Interconnect (PCI) Express x16 graphics card slot on the system board for a discrete graphics card Audio subsystem v Integrated high-definition (HD) audio v Headphone connector and microphone connector on the front panel v Audio line-in connector, audio line-out connector, and microphone connector on the rear panel Connectivity v 10/100/1000 Mbps integrated Ethernet controller...
- Page 11 1. The operating system(s) listed here are being certified or tested for compatibility at the time this publication goes to press. Additional operating systems might be identified by Lenovo as compatible with your computer following the publication of this manual. This list is subject to change. To determine if an operating system has been certified or tested for compatibility, check the Web site of the operating system vendor.
-
Page 12: Specifications
This section provides information about the software provided with your Windows operating system. Software provided by Lenovo The following software programs are provided by Lenovo to help you improve productivity and reduce the cost associated with maintaining your computer. Software programs provided with your computer might vary depending on your model type and preinstalled operating system. - Page 13 Windows XP operating system from Lenovo. Lenovo Welcome: The Lenovo Welcome program introduces some innovative built-in features of Lenovo to you and guides you through some important setup tasks to help you make the most of your computer. Note: The Lenovo Welcome program is only available on computers preinstalled with the Windows 7 operating system or the Windows Vista operating system from Lenovo.
- Page 14 BIOS updates, and other third party applications). Some examples of software that you should keep updated are programs provided by Lenovo, such as the Rescue and Recovery program and the ThinkVantage Productivity Center program. Fingerprint Software: The integrated fingerprint reader provided on some keyboards works with the Fingerprint Software program to enable you to enroll your fingerprint and associate it with your Windows password.
-
Page 15: Locations
Locations This section provides information to help you locate your computer connectors, components, parts on the system board, and internal drives. Locating connectors, controls, and indicators on the front of your computer Figure 1 shows the locations of the connectors, controls, and indicators on the front of your computer. -
Page 16: Locating Connectors And Parts On The Rear Of Your Computer
Locating connectors and parts on the rear of your computer Figure 2 shows the locations of the connectors and parts on the rear of your computer. Some connectors on the rear of your computer are color-coded to help you determine where to connect the cables on your computer. Figure 2. - Page 17 Connector Description Audio line-in connector Used to receive audio signals from an external audio device, such as a stereo system. When you attach an external audio device, a cable is connected between the audio line-out connector of the device and the audio line-in connector of the computer.
-
Page 18: Locating Components
Locating components Figure 3 shows the locations of the various components in your computer. To remove the computer cover and gain access to the inside of the computer, see “Removing the computer cover” on page 14. Figure 3. Component locations 1 Heat sink and fan assembly 6 Front bezel 2 Power supply assembly... -
Page 19: Locating Parts On The System Board
Locating parts on the system board Figure 4 shows the locations of the parts on the system board. Figure 4. System board part locations 1 Microprocessor 12 Front panel connector 2 Microprocessor fan connector 13 USB connectors (2) 3 Memory slots (2) 14 Serial (COM 2) connector 4 Thermal sensor connector 15 Front audio connector... -
Page 20: Locating Internal Drives
Locating internal drives Internal drives are devices that your computer uses to read and store data. You can add drives to your computer to increase storage capacity and enable your computer to read other types of media. Internal drives are installed in bays. In this manual, the bays are referred to as bay 1, bay 2, and so on. -
Page 21: Chapter 2. Installing Or Replacing Hardware
PCI cards, or drives, and maintain your computer by replacing the failing hardware. Notes: 1. Use only computer parts provided by Lenovo. 2. When installing or replacing an option, use the appropriate instructions in this section along with the instructions that come with the option. -
Page 22: Installing External Options
“Important safety information” in the ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide, go to: http://www.lenovo.com/support This section provides instructions on how to remove the computer cover. -
Page 23: Removing And Reinstalling The Front Bezel
“Important safety information” in the ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide, go to: http://www.lenovo.com/support This section provides instructions on how to remove and reinstall the front bezel. - Page 24 3. Remove the front bezel by releasing the three plastic tabs on the top of the front bezel and pivoting the front bezel outward to remove it from the computer. Carefully lay the front bezel aside without disconnecting the power switch and light-emitting diode (LED) assembly cable.
-
Page 25: Accessing The System Board Components And Drives
“Important safety information” in the ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide, go to: http://www.lenovo.com/support This section provides instructions on how to access the system board components and drives. -
Page 26: Installing Or Replacing A Pci Card
“Important safety information” in the ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide, go to: http://www.lenovo.com/support This section provides instructions on how to install or replace a PCI card. - Page 27 b. If the PCI card is secured in place by a retaining latch 1 , press the retaining latch to release the PCI card from the latch. Then, grasp the PCI card by the edges and carefully pull it out of the PCI card slot. If necessary, alternate moving each side of the PCI card a small and equal amount until it is completely removed from the slot.
-
Page 28: Installing Or Replacing A Memory Module
“Important safety information” in the ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide, go to: http://www.lenovo.com/support This section provides instructions on how to install or replace a memory module. - Page 29 To install or replace a memory module, do the following: 1. Remove all media from the drives and turn off all attached devices and the computer. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer. 2.
-
Page 30: Replacing The Battery
“Important safety information” in the ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide, go to: http://www.lenovo.com/support Your computer has a special type of memory that maintains the date, time, and configuration information for built-in features. - Page 31 To replace the battery, do the following: 1. Remove all media from the drives and turn off all attached devices and the computer. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer. 2.
-
Page 32: Replacing The Heat Sink And Fan Assembly
“Important safety information” in the ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide, go to: http://www.lenovo.com/support This section provides instructions on how to replace the heat sink and fan assembly. - Page 33 6. Follow this sequence to remove the four screws that secure the heat sink and fan assembly to the system board: a. Partially remove screw 1 , then fully remove screw 2 , and then fully remove screw 1 . b.
- Page 34 10. Connect the new heat sink and fan assembly cable to the microprocessor fan connector on the system board. See “Locating parts on the system board” on page 11. 11. Lower and position the heat sink fan duct on the top of the heat sink and fan assembly until the four screw holes in the heat sink fan duct are aligned with those in the heat sink and fan assembly.
-
Page 35: Replacing The Microprocessor
“Important safety information” in the ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide, go to: http://www.lenovo.com/support This section provides instructions on how to replace the microprocessor. CAUTION: The heat sink and microprocessor might be very hot. - Page 36 4. Lift the small handle 3 and open the retainer 1 to access the microprocessor 2 . Figure 21. Accessing the microprocessor 5. Lift the microprocessor straight up and out of the microprocessor socket, as shown in Figure 22 on page 29. Notes: a.
- Page 37 d. Do not drop anything onto the microprocessor socket while it is exposed. The socket pins must be kept as clean as possible. Figure 22. Removing the microprocessor 6. Make sure that the small handle is in the raised position. 7.
-
Page 38: Replacing The Power Supply Assembly
“Important safety information” in the ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide, go to: http://www.lenovo.com/support This section provides instructions on how to replace the power supply assembly. - Page 39 2. Remove the computer cover. See “Removing the computer cover” on page 14. 3. Remove the front bezel. See “Removing and reinstalling the front bezel” on page 15. 4. Pivot the drive bay assembly upward, remove the four screws that secure the heat sink fan duct, and then lift the heat sink fan duct out of the chassis.
- Page 40 6. At the rear of the computer, remove the three screws that secure the power supply assembly. Press the power supply clip 1 downward to release the power supply assembly and then slide the power supply assembly to the front of the computer.
- Page 41 Then, install the three screws to secure the new power supply assembly in place. Note: Use only screws provided by Lenovo. Figure 25. Installing the power supply assembly 9. Connect the new power supply assembly cables to all drives and the system board.
- Page 42 10. Lower and position the heat sink fan duct on the top of the heat sink and fan assembly until the four screw holes in the heat sink fan duct are aligned with the corresponding holes in the heat sink and fan assembly. Then, install the four screws to secure the heat sink fan duct in place.
-
Page 43: Replacing The Optical Drive
“Important safety information” in the ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide, go to: http://www.lenovo.com/support This section provides instructions on how to replace the optical drive. - Page 44 7. Press the drive bay assembly clip 1 inward and pivot the drive bay assembly downward as shown. Figure 28. Lowering the drive bay assembly 8. Slide the optical drive out of the front of the computer. Figure 29. Removing the optical drive User Guide...
- Page 45 9. Slide the new optical drive into the optical drive bay from the front of the computer. Figure 30. Installing a new optical drive 10. Hold the new optical drive and pivot the drive bay assembly upward. Align the screw holes in the new optical drive with the corresponding holes in the drive bay.
-
Page 46: Replacing The Hard Disk Drive
“Important safety information” in the ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide, go to: http://www.lenovo.com/support This section provides instructions on how to replace the hard disk drive. - Page 47 4. Note the location of the four screws 1 that secure the hard disk drive. Then, pivot the drive bay assembly upward. Figure 33. Pivoting the drive bay assembly 5. Hold the hard disk drive and remove the four screws that secure the hard disk drive.
- Page 48 6. Connect one end of the signal cable to the rear of the new hard disk drive and the other end to an available SATA connector on the system board. See “Locating parts on the system board” on page 11. Then, locate an available five-wire power connector and connect it to the rear of the new hard disk drive.
-
Page 49: Replacing The Front Fan Assembly
“Important safety information” in the ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide, go to: http://www.lenovo.com/support This section provides instructions on how to replace the front fan assembly. - Page 50 8. The front fan assembly is attached to the chassis by four rubber mounts. Remove the front fan assembly by cutting the rubber mounts and lifting the front fan assembly out of the chassis. Figure 37. Removing the front fan assembly User Guide...
- Page 51 9. Install the new front fan assembly by aligning the new rubber mounts that came with the new front fan assembly with the corresponding holes in the chassis, and then push the rubber mounts through the holes. Then, carefully pull on the tips of the rubber mounts from the bottom until the new front fan assembly is secured in place.
-
Page 52: Replacing The Usb Keyboard Or Mouse
“Important safety information” in the ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide, go to: http://www.lenovo.com/support This section provides instructions on how to replace the USB keyboard or mouse. -
Page 53: Obtaining Device Drivers
Setup Utility program. See Chapter 4, “Using the Setup Utility program,” on page 57. Note: In most areas of the world, Lenovo requires the return of the defective Customer Replaceable Units (CRUs). Information about this will come with the new CRUs or will come a few days after you receive the new CRUs. -
Page 54: Integrated Cable Lock
The cable lock also locks the computer cover. See Figure 41. This is the same type of lock used with many notebook computers. You can order an integrated cable lock from Lenovo by searching for Kensington at: http://www.lenovo.com/support Note: Make sure that the integrated cable lock you installed does not interfere with other computer cables. -
Page 55: Padlock
Padlock Your computer is equipped with a padlock loop so that the computer cover cannot be removed when a padlock is installed. Figure 42. Installing a padlock Password protection To deter unauthorized use of your computer, you can use the Setup Utility program to set a password. - Page 56 5. Move the jumper from the standard position (pin 1 and pin 2) to the maintenance position (pin 2 and pin 3). 6. Reinstall any parts and reconnect any cables that have been removed or disconnected. 7. Reinstall the computer cover and reconnect the power cords for the computer and monitor.
-
Page 57: Chapter 3. Recovery Information
″creating Product Recovery discs.″ v To create recovery media on the Windows 7 operating system, click Start → All Programs → Lenovo ThinkVantage Tools → Factory Recovery Disks. Then, follow the instructions on the screen. -
Page 58: Using Recovery Media
v To create Product Recovery discs on the Windows Vista operating system, click Start → All Programs → ThinkVantage → Create Product Recovery Media. Then, follow the instructions on the screen. v To create Product Recovery discs on the Windows XP operating system, click Start →... -
Page 59: Performing Backup And Recovery Operations
To perform a backup operation using the Rescue and Recovery program on the Windows 7 operating system, do the following: 1. From the Windows desktop, click Start → All Programs → Lenovo ThinkVantage Tools → Enhanced Backup and Restore. The Rescue and Recovery program opens. -
Page 60: Using The Rescue And Recovery Workspace
1. From the Windows desktop, click Start → All Programs → Lenovo ThinkVantage Tools → Enhanced Backup and Restore. The Rescue and Recovery program opens. 2. In the Rescue and Recovery main window, click the Launch advanced Rescue and Recovery arrow. -
Page 61: Creating And Using A Rescue Medium
Attention: If you restore the hard disk drive from a Rescue and Recovery backup or restore the hard disk drive to the factory default settings, all files on the primary hard disk drive partition (usually drive C:) will be deleted in the recovery process. -
Page 62: Using A Rescue Medium
To create a rescue medium on the Windows 7 operating system, do the following: 1. From the Windows desktop, click Start → All Programs → Lenovo ThinkVantage Tools → Enhanced Backup and Restore. The Rescue and Recovery program opens. -
Page 63: Installing Or Reinstalling Device Drivers
Device drivers for factory-installed devices are located on the computer hard disk drive (usually drive C:) in the SWTOOLS\DRIVERS subdirectory. The latest device drivers for factory-installed devices are also available at http://www.lenovo.com/ support. Other device drivers are on the software media that come with individual devices. - Page 64 the startup device sequence. For more information about the Setup Utility program, see Chapter 4, “Using the Setup Utility program,” on page 57. It is important to create a rescue medium, a recovery repair diskette, and a set of recovery media as early as possible and store them in a safe place for future use. User Guide...
-
Page 65: Chapter 4. Using The Setup Utility Program
Set Power-On Password v Set Administrator Password You do not have to set a password to use your computer. However, using a password improves computing security. If you decide to set a password, read the following sections. © Copyright Lenovo 2010... -
Page 66: Password Considerations
Password considerations A password can be any combination of up to 16 (1 to 16) alphabetic and numeric characters. For security reasons, it is recommended to use a strong password that cannot be easily compromised. To set a strong password, use the following guidelines: Note: The Setup Utility program passwords are not case sensitive. -
Page 67: Enabling Or Disabling A Device
Enabling or disabling a device This section provides instructions on how to enable or disable user access to a device. SATA Controller When this option is set to Disabled, all devices connected to the SATA connectors (such as the hard disk drive and the optical drive) are disabled and will not be displayed in the system configuration. -
Page 68: Viewing Or Changing The Startup Device Sequence
Note: Selecting a startup device on the Startup Device Menu does not permanently change the startup device sequence. Viewing or changing the startup device sequence This section provides instructions on how to view or permanently change the configured startup device sequence. To view or permanently change the configured startup device sequence, do the following: 1. -
Page 69: Chapter 5. Updating System Programs
Lenovo might make changes and enhancements to the POST and BIOS. When updates are released, they are available as downloadable files on the Lenovo Web site at http://www.lenovo.com. Instructions for using the POST and BIOS updates are available in a TXT file that is included with the update files. -
Page 70: Updating (Flashing) The Bios From Your Operating System
Updating (flashing) the BIOS from your operating system Note: Because Lenovo makes constant improvements to its Web sites, the Web page contents are subject to change without notice, including the contents referenced in the following procedure. - Page 71 8. Turn on the computer and then insert the POST and BIOS update (flash update) disc into the optical drive. The recovery session begins. The recovery session will take two to three minutes. During this time, you will hear a series of beeps.
- Page 72 User Guide...
-
Page 73: Chapter 6. Troubleshooting And Diagnostic Programs
You can also get the latest service and support telephone numbers and a PDF version of the ThinkCentre Safety and Warranty Guide from the Lenovo Support Web site at: http://www.lenovo.com/support Symptom... -
Page 74: Diagnostic Programs
To run the Lenovo ThinkVantage Toolbox program on the Windows 7 operating system, click Start → All Programs → Lenovo ThinkVantage Tools → System Health and Diagnostics. -
Page 75: Pc-Doctor For Dos
PC-Doctor for DOS You can also download the latest version of the PC-Doctor for DOS diagnostic program from http://www.lenovo.com/support. The PC-Doctor for DOS diagnostic program runs independently of the Windows operating system. Use the PC-Doctor for DOS diagnostic program if you are unable to start the Windows operating system. -
Page 76: Cleaning An Optical Mouse
Cleaning an optical mouse This section provides instructions on how to clean an optical mouse. An optical mouse uses a LED and an optical sensor to navigate the pointer. If the pointer on the screen does not move smoothly with the optical mouse, you might need to clean the mouse. -
Page 77: Chapter 7. Getting Information, Help, And Service
PDF file and you will be guided through the Adobe Reader installation. 2. The publication is available in other languages on the Lenovo Support Web site http://www.lenovo.com/support 3. If you want to install a different language version of the Adobe Reader... -
Page 78: Thinkvantage Productivity Center
Windows 7 operating system or the Windows Vista operating system from Lenovo. The Lenovo Welcome program introduces some innovative built-in features of Lenovo to you and guides you through some important setup tasks to help you make the most of your computer. Access Help... -
Page 79: Lenovo Web Site (Http://Www.lenovo.com)
You can get the latest technical information and download device drivers and updates from the Lenovo Support Web site at: http://www.lenovo.com/support Calling for service During the warranty period, you can get help and information from the Lenovo Customer Support Center by telephone. Chapter 7. Getting information, help, and service... -
Page 80: Using Other Services
You must retain your proof of purchase to obtain warranty service. For a list of the Lenovo Support phone numbers for your country or region, go to http://www.lenovo.com/support and click Support phone list or refer to the ThinkCentre Safety and Warranty Guide that is provided with your computer. -
Page 81: Purchasing Additional Services
Service availability and service name might vary by country or region. For more information about these services, go to the Lenovo Web site at: http://www.lenovo.com Chapter 7. Getting information, help, and service... - Page 82 User Guide...
-
Page 83: Appendix. Notices
Web sites. The materials at those Web sites are not part of the materials for this Lenovo product, and use of those Web sites is at your own risk. -
Page 84: Television Output Notice
European conformance CE mark Trademarks Lenovo, the Lenovo logo, Personal System/2, PS/2, Rescue and Recovery, ThinkCentre, and ThinkVantage are trademarks of Lenovo in the United States, other countries, or both. Microsoft, Windows, and Windows Vista are trademarks of the Microsoft group of companies. - Page 85 65 installing options diagnostic programs, using 71 security features 45 documentation, using 71 installing, replacing drivers, device 45 memory module 20 drives PCI card 18 internal 12 internal drives 12 internal drives 1 © Copyright Lenovo 2010...
- Page 86 44 rear connectors 8 recovering from a POST and BIOS update failure 62 software 49 recovery Lenovo Customer Support Center 71 Boot-block Recovery 62 Lenovo ThinkVantage Toolbox 66 operations, backup and 51 Lenovo ThinkVantage Tools 69 problems, solving 55...
- Page 87 53 diagnostic programs 71 documentation 71 other services 72 passwords 57 Setup Utility program 57 VGA monitor connector 9 video subsystem 1 viewing or changing settings 57 warranty information 70 Web site, Lenovo 71 workspace, backup and recovery 52 Index...
- Page 88 User Guide...
- Page 90 Part Number: 71Y8530 Printed in USA (1P) P/N: 71Y8530...