THUNDER TIGER TITAN X50 Quick Start Manual page 2

2. Screw the Shaft End onto the Tail Drive Shaft with a drop of threadlocker
as the drawing, but do not over tighten.
3. Add a drop of thin CA glue on the Tail Drive Shaft next to where the
bearing should be, and then slide the bearings over the position quickly;
the distance from the Shaft Drive End to the Rubber Shaft Bearing
Support is approx. 350mm / 13.78".
4. Apply some amount of silicon oil or Vaseline onto the rubber surface for
easy install into the tail boom later.
5. Note to line up the screw holes and then insert the Connector into the Tail
Drive Shaft with a drop of CA. Tighten the setting screws with nuts.
2. 參考圖示，塗抹些許防鬆膠將尾傳動軸接頭鎖在尾傳動軸上，勿過度鎖緊。
3. 在尾傳動軸上軸承固定位置前方，塗抹少量快乾膠，迅速滑動軸承至定位固
定；該定位大約距離軸傳動接頭350mm / 13.78"處。
4. 塗抹些許矽膠油脂或凡士林於橡膠軸套表面上，稍後將尾驅動軸組裝入尾管
時，會較為容易。
5. 注意對正螺絲鎖固孔位，將傳動軸連接頭插入尾驅動軸，並以快乾膠接著。
鎖緊螺絲及螺帽。
Step 3 Tail Rotor Head Set 尾旋翼機構組
No. Material No. Description
名稱
1 BK2280 TAIL ROTOR SHAFT
尾旋翼橫軸(軸傳)
* 2 HME3-3B SET SCREW,M3x3
無頭內六角螺絲,M3x3
* 3 BK2284 TAIL ROTOR HUB
尾旋翼T型座
4 BK2580 METAL TAIL GRIP
金屬尾旋翼座
5 HMV1050ZZWY BEARING, d5xD10xW3
滾珠軸承,d5xD10xW3
*
6 BK0082 COLLAR, d2xD3xW4.2
軸環,d2xD3xW4.2
* 7 HMC2-10B SOCKET SCREW, M2×10
內六角螺絲,M2×10
* 8 BK0083 PIN, D2x8.8
固定銷,D2x8.8
* 9 TAIL PITCH CONTROL LINK
BK0026
尾旋翼連接頭
*
10 HMC25-6B SOCKET SCREW, M2.5x6
內六角螺絲,M2.5x6
11 HMO26 WASHER, d2.8xD5xW0.5
墊片,d2.8xD5xW0.5
*
12 BK2276 WASHER, d4xD6xW0.5
尾旋翼轉座墊片,d4xD6xW0.5
* 13 HMV940ZZY BEARING, d4xD9xW4
滾珠軸承,d4xD9xW4
* 14 HMX0409Y THRUST BEARING, d4xD9xW4
止推軸承,d4xD9xW4
1. Note the orientation of the Thrust Bearings; please refer your X50B manual: Diagram for Thrust Bearing Assembly.
2. Line up the concave of Tail Rotor Shaft and the hole of Hub when securing the Tail Rotor Hub onto the Tail Rotor Shaft.
3. Assemble the tail unit as drawing. Secure the screws with a drop of threadlocking but not over tighten, to ensure the moveable parts run smoothly.
1. 請參考您手上的 X50B 說明書，止推軸承安裝示意圖，注意安裝方向性。
2. 將尾旋翼固定座鎖上尾旋翼主軸時，請注意軸上凹槽需對正固定座上螺絲孔。
3. 依圖示順序組裝。使用適量防鬆劑固定，但請勿過度鎖緊，確保每個可動機構皆作動順暢。
Step 4 Tail Boom & Unit 尾管及尾座
No. Material No. Description
名稱
1
BK2501 METAL TAIL UNIT HOUSING
金屬尾座
2 BK2502 METAL TAIL PITCH CONTROL HOUSING
尾旋翼控制桿座
3 HMC25-8B SOCKET SCREW, M2.5x8 內六角螺, M2.5x8
4 HMV1350ZZY BEARING, d5xD13xW4 滾珠軸承, d5xD13xW4
5 HMV6701ZZY BEARING, d12xD18xW4 滾珠軸承, d12xD18xW4
6 COLLAR, d15xD18x6.8L
BK2291 軸環, d15xD18x6.8L
7 BK0372 TAIL INPUT GEAR
尾齒輪/INPUT-20T
8 BK0373-2 TAIL OUTPUT GEAR
尾齒輪/OUTPUT-20T
9 BA1144-1 WASHER, d5xD8xW0.15 軸承墊片, d5xD8xW0.15
10 HMY2-10 PIN D2x10 固定銷, d2x10
11 BK2512 TAIL PITCH CONTROL LEVER
尾旋翼控制桿
* 12 BEARING, d4xD7xW2.5
HMV740ZZY 滾珠軸承, d4xD7xW2.5
*
13 BK0649-2 LINKAGE BALL(B)
內六角連接頭自攻螺絲(B)
14 BK0077 COLLAR, d3xD4xW6 軸環, d3xD4xW6
15 HMC3-10B SOCKET SCREW, M3x10 內六角螺絲, M3x10
* 16 BK2190 CARBON VERTICAL FIN
碳纖維垂直尾翼
17 SOCKET SCREW, M3x6
HMC3-6B 內六角螺絲, M3x6
18 BK2503 TAIL ROTOR CASE BUTTON
尾管固定片
19 HMC2-5B SOCKET SCREW, M2x5 內六角螺絲, M2x5
20 BK0859-2 TAIL BOOM
尾管
21 BK2559 ROD GUIDE
固定環
22 HNN2-6B TAPPING SCREW, M2×6
墊圈自攻螺絲, M2×6
*
23 HMC3-16B SOCKET SCREW, M3x16 內六角螺絲, M3x16
*
24 HMM3Z NYLON NUT(M3)
止鬆螺帽(M3)
*
25 BK0404-B TAIL BLADE(BLACK)
尾旋翼(黑)
26 HME3-4B SET SCREW(M3x4) 無頭內六角螺絲, M3x4
1. Assemble the Metal Tail Unit / Tail Boom & its stuffs as drawing.
2. Check the mesh of #7 & #8, please add the Washers (#9) for a proper
mesh if too much play.
1. 依照圖示組裝金屬尾座／尾管及零件
2. 請檢查 #7 及 #8 的齒輪間隙，間隙過大時請酌加墊片(#9)。
2
No. Material No. Description
名稱
3 BK0367 TAIL DRIVE SHAFT LINKER
尾驅動連接棒
4 BK2552 TAIL DRIVE SHAFT
尾驅動軸
5 HMC2512B SOCKET SCREW, M2.5x12 內六角螺絲, M2.5x12
6 HMM25Z NYLON NUT, M2.5 止鬆螺帽, M2.5
Tail
尾座
(5)
(4)
(6)
(6)
(5)
Apply C.A Glue
使用快乾膠黏合
T22/#262
(2)
(3)
Qty
(7)
1
(5)
(4)
2
1
2
2
(8)
2 (12)
(6)
(2)
2
(9)
2
(1)
2
2
4
2
2
2
(1)
Qty
(2)
1
(4)
T22/#262
1
(5)
1 (3)
(4)
2
(6)
2
(5)
1
(7)
(24)
1
1
1
1
1
(24)
AC
(26)
1
T22/#262
(10)
1
(12)
1
(8)
2 (9)
2
(13)
(17) (12)
1
(14)
T22/#262
1 (15)
1 (15)
T22/#262
(18)
1
(19)
(20)
3
T22/#262 (16) (21)
3
2
2
(21)
(22)
2
1
(21)
(22)
(22)
Step 5 Main Gear Set 主齒輪組
Qty
2
No. Material No. Description
1
* 1 ONE WAY BEARING SHAFT
BK2282
2
*
2 BV2281 ONE WAY CLUTCH HOUSING
2
*
3 BK2285 MAIN GEAR,85T
*
4 HSA3-8 BUTTON HEAD SOCKET SCREW,M3x8
*
5 BK2524 MAIN GEAR WASHER
6 BK2287 AUTOROTATION TAIL DRIVE PULLEY,80T
*
7 HMC3-10B SOCKET SCREW,M3x10
*
8 BK0087 WASHER,d3xD8xW1.4
*
9 BK1197 MAIN SHAFT BOLT,M3x20
CA *
10 BK2290 COLLAR
*
11 HMM3Z NYLON NUT,M3
CA
(3)
(1)
Nose
機頭
(2)
(3)
T22/#262
T22/#262
(4)
(14)
(13)
T22/#262
(6)
(11)
(10)
Step 6 Tail Unit Assembly 尾部總成組裝
1. Ensure the setting screw (#4) line up
to the retaining hole.
2. Secure the screws into the Frame
Spacer when attaching the Tail Support Rod
End on the Main Frames.
3. Refer your original manual to assemble the rudder
linkage rod back, and re-adjust the length.
1. 鎖固時，請確認鎖固螺絲正確對正定位孔。
2. 安裝尾管支撐桿於側板上時，請注意需
將鎖固螺絲鎖固於六角固定支柱上。
3. 參考您手上的說明書將尾舵拉桿裝回，
並重新調整長度。
No. Description
Material No.
*
1 BK2219 FRAME SPACER
*
2 HMC3-14B SOCKET SCREW , M3x14
3 HSA3-6 BUTTON HEAD SOCKET SCREW, M3X6
(25)
* 4 BK0797 TAIL SUPPORT BRACKET(UPPER)
(23)
Caution 注意事項
Preflight check both the mechanism settings and blade tracking is recommended, please refer your original instruction manual of Titan X50B. (Or you may
(23) download the new manual of Titan X50 (torque tube version) from www.thundertiger.com for reference.)
飛行前，請翻閱您手上的Titan X50B組裝說明書，務必再次確認機構設定及主旋翼軌跡是否正確。
（或您也可至雷虎科技網站下載新版Titan X50軸傳版說明書。）
(25)
Spare Parts 零件包
(11)
PV0149-1 TAIL GEAR, X50
尾齒輪
PV1368 BEARING BLOCK SET
軸傳軸承座組
Qty
名稱
1
單向軸套
1
單向離合組
1
主齒輪,85T
4
半圓頭內六角螺絲,M3x8
1
主齒輪墊片
1
軸傳尾驅動主齒,80T
4
內六角螺絲,M3x10
4
墊片,d3xD8xW1.4
1
內六角半牙螺絲,M3x20
1
軸環
1
止鬆螺帽,M3
(8)
Note the chamfer
should point up.
T22/#262
注意有倒角端朝上
(7)
T22/#262
BV2281
(9)
1. Refer your original X50B manual to remove the main rotor head set from the model and disassemble the
Main Gear Set.
(4)
(5)
2. Re-build the gear set and install the new Main Gear Set back inside the main frame as drawing.
1. 請參考您手上的X50B說明書，將主旋翼頭總成由機體上取下，並分解主齒輪組。
2. 請依照圖示重新組裝主齒輪組，並組裝回機體上。
(3)
(3)
(2) (1)
(2)
Qty No.
Material No.
名稱
*
1 5 BK0798
六角連接支柱
*
內六角螺絲, M3x14 2 6 HMC3-16B
*
半圓頭內六角螺絲, M3x6 2 7 HMM3Z
1
固定座(上)
PV0521-2 TAIL BOOM PV1331-1 METAL TAIL GRIP,X50 PV1366 TAIL GEAR MOUNT SET
尾管 金屬尾旋翼座(軸傳)
PV1369 TAIL DRIVE GEAR SHAFT PV1370 TAIL DRIVE GEAR-16T SET PV1371 TAIL GEAR SET
軸傳驅動軸 軸傳尾驅動輪16T
(8)
(7)
T22/#262 T22/#262
(10)
(11)
(6)
(4)
(5)
(7)
Rear View 後視圖
(2) (1) (2)
Description Qty
名稱
TAIL SUPPORT BRACKET(LOWER) 1
固定座(下)
SOCKET SCREW-M3x16 內六角螺絲, M3x16 2
NYLON NUT(M3) 2
止鬆螺帽(M3)
PV1367 TAIL PITCH CONTROL LEVER SET
傘齒輪固定座 尾旋翼控制桿組
PV1372 METAL TAIL UNIT HOUSING SET
傘齒輪, 25T
金屬尾座
3