Controls And Their Functions - Panasonic AKHC3500 - MULTI FORMAT CAMERA Operating Instructions Manual

Controls and their functions

 Lens mount (Bayonet type)
This is where the lens is mounted.
 Lens clamp lever
The lens is inserted into the lens mount , and this lever
is then turned to clamp the lens in place.
 Lens cable, mic cable clamps
These are used to clamp the lens cable and mic cable in
place.
D Camera hangers (supplied)
When the buildup unit (AK-HBU3500) is used, install
these hangers to the camera with supplied screws
(M3  8 mm).
For details, refer to the Operating Instructions for
AK-HBU3500.
E Tripod mount
Before securing the Multi-Format Camera to a tripod,
attach the tripod adapter (SHAN-TM700) which is
available as an optional accessory.
F Shoulder pad
This is used when the Multi-Format Camera is to be
carried on the shoulder.
G Slide lock release lever
This is held down while it is used to adjust the front/back
position of the shoulder pad F.
H Shoulder strap fitting
This enables the shoulder belt to be attached.
I Optical cable clamp
This enables the optical cable to be clamped.
J Camera No. plate holder
This enables the accessory camera No. plate to be
attached.
K Optical fiber connector
(EDW.3K made by LEMO)
 Camera power switch [POWER]
This is used to select the camera power input (power
supplied from the CCU or from an external connector)
and turn the power ON and OFF.
 Power LED
This lights up green when power is supplied to the
camera.
When the camera's power switch is set to OFF, this lights
up red if the CCU is connected, and it goes off if the CCU
is not connected.
 Power circuit breaker [BREAKER]
This shuts off the power in the event of an overcurrent
while the DC 1 V power supply is used.
To reset it, press the circuit breaker button.
 INCOM connectors 1, 2 [INCOM1, INCOM2]
The INCOM or headset plugs are connected here.
 INCOM1 MIC ON/OFF switch [MIC1 TALK]
This is the INCOM1 MIC ON/OFF selector switch.
 INCOM1 level control [INCOM1 LEVEL]
This is used to adjust the INCOM1 receive level.
 INCOM2 MIC ON/OFF switch [MIC2 TALK]
This is the INCOM MIC ON/OFF selector switch.
 INCOM2 level control [INCOM2 LEVEL]
This is used to adjust the INCOM receive level.
9 INCOM1 PGM1 level control [INCOM1 PGM1]
This is used to adjust the INCOM1 and PGM1 mixing
level.
 INCOM1 PGM2 level control [INCOM1 PGM2]
This is used to adjust the INCOM1 and PGM mixing
level.
 INCOM2 PGM1 level control [INCOM2 PGM1]
This is used to adjust the INCOM and PGM1 mixing
level.
 INCOM2 PGM2 level control [INCOM2 PGM2]
This is used to adjust the INCOM and PGM mixing
level.
 RET-A selector switch [RET A]
This switch is used to select the return images to be
switched by RET-A.
 RET-B selector switch [RET B]
This switch is used to select the return images to be
switched by RET-B.
 CALL LED
This lights up green when the CALL switch is pressed.
It also lights in response to a call from the ROP or MSU.
 CALL switch [CALL]
This lights the CALL LED on the ROP or MSU and
sounds the buzzer.
 OPT LED
This indicates the camera's optical signal reception
status. It normally lights up green. When any problem has
occurred, it lights up red.
When a problem has occurred, clean the optical fiber
connector.
8