Software Flow Chart; Throttle Parameter Settings - NOVAK HAVOC SPORT ESC - CUSTOM PROGRAMMING AND GEARING Instructions

H AV O C s p O R t E s C C u s t O m p R O G R A m m I N G
pleASe noTe: This page contains optional Advanced Programming items!
(But don't worry, you can always reset factory defaults by performing the One-Touch programming again, so go ahead & experiment—that's why the programming is in there, right?)
HAvOC SPORT ESC SOFTWARE FLOW CHART
The Havoc Sport ESC features nine parameters that can be adjusted.
Default settings are in bold in tables.
Transmitter can be either ON or OFF:
1. iF TrAnSMiTTer iS oFF, DiSConneCT eSC FroM reCeiver
Remove input signal harness from the receiver to avoid radio interference.
2. ConneCT eSC To A ChArGeD BATTerY pACK
3. SliDe eSC's on/oFF SwiTCh To 'on' poSiTion
4. wiTh eSC AT neuTrAl preSS & holD eSC'S SeT BuTTon
release EsC's sET button once LED is at desired setting.
To skip a parameter, press and hold ESC's SET button to the desired parameter.
5. SeleCT pArAMeTer vAlue
LED flashes to indicate active setting (refer to tables at right). Quick press & release
SET button to select desired setting.
6. preSS & holD SeT BuTTon To STore SeleCTion
When SET button is pressed and held for about 1 second, the new selection is
stored in ESC's memory—The 4 status LEDs will scroll across to indicate ESC is
exiting programming and ESC returns to neutral.
note: There is no time constraint during selection process of custom parameters.
HAvOC SOFTWARE
@neuTrAl
FLOW CHART:
RED LED on solid
Min. BrAKe
DrAG BrAKe
BLUE & AMBER
DeAD BAnD
Min. Drive
ThroTTle Curve*
BrAKe FreQuenCY*
RED / GREEN / AMBER
MoTor roTATion*
RED / GREEN / BLUE
li-po CuT-oFF
Exit Programming
@neuTrAl
RED LED on solid
restOriNg factOrY defauLts :
perform one-Touch Set-up to default eSC back to factory default parameters.
press & hold
BLUE
press & hold
press & hold
BLUE & GREEN
press & hold
AMBER
if Brushed Mode
press & hold
is active
GREEN
press & hold
RED
press & hold
reverSe*
press & hold
press & hold
RED & AMBER
press & hold
all LEDs
flash 5 times
LEDs roll off
*Not adjustable
in brush mode.

THROTTLE PARAMETER SETTINGS

1. MiNiMuM BraKe settiNgs (10)
Amount of braking applied with first pulse of transmitter throttle information.
>>raising this setting starts the braking at a stronger/higher level
setting (# of flashes)
Minimum Brake (%):
2. drag BraKe settiNgs (10)
Amount of braking applied while transmitter is at neutral. 'Coast' brakes.
>>raising this setting makes the motor slow down more, without
pushing the transmitter's trigger into the brake/reverse direction.
setting
(# of flashes)
Drag Brake (%):
3. dead BaNd settiNgs (5)
Space between Minimum Brake & Minimum Drive, with neutral in middle.
>>raising this setting will increase the 'free play', or distance your
trigger must move before forward drive or braking will begin.
setting (# of flashes)
Dead Band (%):
4. MiNiMuM driVe settiNgs (5)
Amount of forward drive applied with first pulse of transmitter information.
>>raising this setting makes the motor start at a stronger/higher
level so it takes off more aggressively from neutral.
setting
(# of flashes)
Minimum Drive (%):
5. tHrOttLe curVe seLectiON* (2)
>>Changing this setting changes the throttle response and ease of
driveability. Note: Setting is fixed at "Linear" in Brush Mode.
setting (# of flashes)
Throttle Curve:
6. BraKe freQueNcY* (7)
>>raising this setting makes the brake response smoother and
more controllable.
setting (# of flashes)
Brake Frequency (KHz):
7. reVerse* (2)
>>Changing this setting activates/deactivates reverse direction.
setting (# of flashes)
reverse (On/Off):
8. MOtOr rOtatiON* (2)
>>Changing this setting changes direction of motor rotation.
setting (# of flashes)
Motor rotation (CCW/CW):
9. Li-PO cut-Off (2)
>>Changing this setting enables/disables li-po cutoff (@6.25 volts).
setting (# of flashes)
li-po Cut-off (On/Off):
P6
No further adjustments are required.
(Defaults in Bold)
1 2 3 4 5 6 7
0 3 6 9 12 15 18 21 24
BLUE & AMBER LEDs
1 2 3 4 5 6 7
0 3 6 12 15 18 21 24
9
BLUE & GREEN LEDs
1 2 3 4
2 3 4 5
AMBEr LED
1 2 3 4
1 2 3 4
GrEEN LED
1
Linear
expo
1 2 3 4 5
1 2 3 4 5
RED, GREEN & AMBER LEDs
1
Off (FWD/BRK) on (FwD/BrK/rev)
RED, GREEN & BLUE LEDs
1
q
CCw
RED & AMBER LEDs
1
OFF
BLUE LED
.
8 9 10
27
8 9 10
27
5
6
5
5
2
rED LED
6 7
7.5 8
2
2
p
CW
2
on