Advertisement
PLEASE NOTE: This page contains optional Advanced Programming items!
(but don't worry, you can always reset factory defaults by performing the One-Touch programming again, so go ahead & experiment--that's why the programming is in there, right?)
Throttle Profiles 1, 2, 3, 4, & 6 can be independently customized to
fine tune the speed control to feel just the way you like it.
The GTB lets you adjust the following software parameters:
• Minimum Brake/Drag Brake Percentage--1 of 10 settings.
• Braking Type--1 of 2 types of braking styles (standard Constant Force braking
or DRAG BRAKING where braking is applied during neutral).
• Dead Band--1 of 5 Dead Band settings from 2 to 6%.
• Drive Frequency (Profile 6 only)--1 of 7 Drive Frequencies from 1.5 to 11kHz.
• Minimum Drive Percentage--1 of 5 settings from 2 to 12%.
gtb soFtware Flow chart
gtb soFtware Flow chart
gtb soFtware Flow chart
gtb soFtware Flow chart
gtb soFtware Flow chart
@NEUTRAL
RED or RED & GREEN
MIN. BRAKE
DRAG BRAKE
BLUE & AMBER
DEAD BAND
BLUE & GREEN
MIN. DRIVE
if Brush-Mode
is active
DRIVE FREQUENCY
GREEN
press & hold
ACTIVE PROFILE
all LEDs (flashing)
if Brush-Mode
is active
––––––
all LEDs
flash 6 times
LEDs roll off
––––
exit programming
@NEUTRAL
RED or RED & GREEN
restoring factory default
restoring factory defaults s s s s
restoring factory default
restoring factory default
restoring factory default
Every time you perform the One-Touch Set-Up, the factory default settings are
restored for each of the throttle profiles.
: : : : :
press & hold
BLUE
press & hold
press & hold
press & hold
AMBER
press & hold
if Brushless-Mode
is active
if Brushless-Mode
is active
––––––
# of flashes equals
active profile ( 1-5 )
if pressed
––––––
within 3 sec. of
all LEDs flashing
––––––
active profile
changed
if not pressed
––––––
within 3 sec. of
all LEDs flashing
: : : : :
to customizing profiles
to customizing profiles
to customizing profiles
to customizing profiles
to customizing profiles
With ESC on & connected to a charged battery (transmitter ON or OFF):
1. IF TRANSMITTER IS OFF, DISCONNECT ESC FROM RECEIVER
Remove input signal harness from receiver to avoid radio interference.
2. MAKE SURE THROTTLE PROFILE 1-4 OR 6 IS ACTIVE
If you are not sure what profile is selected, follow the procedures in 'Throttle
Profile Selection' to check or select desired profile.
Remember that you can not access the Brush-Mode
disconnecting the brushless motor's sensor harness from the ESC.
Note: there is no time constraint during selection process of custom parameters.
to adjust minimum brake
to adjust minimum brake
to adjust minimum brake
to adjust minimum brake
to adjust minimum brake
a a a a a . . . . . PRESS & HOLD SPEED CONTROL'S SET BUTTON
With ESC at neutral, press & hold SET button until the Blue status LED
turns on solid---Release ESC's SET button once LED is on solid.
b b b b b . . . . . SELECT MINIMUM BRAKE PERCENTAGE
Blue status LED (1st LED on left) flashes to indicate active Minimum Brake
setting. Quick press & release to select desired setting.
Setting
(# of flashes)
Minimum Brake
(%)
c c c c c . . . . . PRESS & HOLD SET BUTTON TO STORE SELECTION
When SET button is pressed & held for about 1 second, the new selection is
stored in ESC's memory--The 4 status LEDs will scroll back & forth to indicate
you are exiting programming & the Red LED will turn on solid (Red & Green if no
transmitter signal present)--ESC is at neutral & ready to go.
to activate & adjust drag brake
to activate & adjust drag brake
to activate & adjust drag brake
to activate & adjust drag brake
to activate & adjust drag brake
a a a a a . . . . . PRESS & HOLD SPEED CONTROL'S SET BUTTON
With ESC at neutral, press & hold SET button until Blue & Amber status
LEDs turn on solid---Release SET button once LEDs are solid.
b b b b b . . . . . SELECT DRAG BRAKE PERCENTAGE
Blue & Amber status LEDs (1st & 2nd LEDs on left) flash to indicate active
Drag Brake setting (Drag brake setting will be same as Minimum Brake setting).
Quick press & release to change Drag Brake/Minimum Brake setting, then
press & hold SET button for about 1 second to activate drag braking, store
selection into ESC's memory, and return to neutral.
Setting
(# of flashes)
Drag Brake
(%)
Note: To re-activate the standard style of braking (no drag brakes during
neutral), repeat Minimum Brake adjustment as described above.
to adjust dead band
to adjust dead band
to adjust dead band
to adjust dead band
to adjust dead band
a a a a a . . . . . PRESS & HOLD SPEED CONTROL'S SET BUTTON
With ESC at neutral, press & hold SET button until Blue & Green status
LEDs turn on solid---Release SET button once LEDs are solid.
b b b b b . . . . . SELECT DEAD BAND PERCENTAGE
Blue & Green status LEDs flash to indicate active Dead Band setting. Quick
press & release to change setting, then press & hold SET button for about 1
second to store selection and return to neutral.
Setting
(# of flashes)
Dead Band
to adjust minimum drive
to adjust minimum drive
to adjust minimum drive
to adjust minimum drive
to adjust minimum drive
a a a a a . . . . . PRESS & HOLD SPEED CONTROL'S SET BUTTON
With ESC at neutral, press & hold SET button until Amber status LED turns
on solid---Release SET button once LED is on solid.
b b b b b . . . . . SELECT MINIMUM DRIVE PERCENTAGE
Amber status LED flashes to indicate active Minimum Drive setting. Quick
press & release to change setting, then press & hold SET button for about 1
second to store selection and return to neutral.
Setting
(# of flashes)
Minimum Drive
to adjust drive frequency
to adjust drive frequency
to adjust drive frequency
to adjust drive frequency
to adjust drive frequency
a a a a a . . . . . PRESS & HOLD SPEED CONTROL'S SET BUTTON
With ESC at neutral, press & hold SET button until Green status LED turns
on solid---Release SET button once LED is on solid.
b b b b b . . . . . SELECT DRIVE FREQUENCY
Green status LED flashes to indicate active Drive Frequency setting. Quick
press & release to change setting, then press & hold SET button for about 1
second to store selection and return to neutral.
Setting
(# of flashes)
Drive Frequency
(kHz)
P6
No further adjustments are required.
1 1 1 1 1
4 4 4 4 4
- - - - -
(Profile #6)
: : : : :
(or re-activate std-style brakes)
:
1 2 3 4 5 6 7 8 9 10
:
5 10 15 20 25 30 35 40 45 50
blue & amber
:
1 2 3 4 5 6 7 8 9 10
:
off 10 15 20 25 30 35 40 45 50
: : : : :
blue & green
:
1
2
3
4
:
2
3
4
5
(%)
amber
:
1
2
3
4
:
2
3
5
8
(%)
: : : : :
green
:
1
2
3
4
5
:
1.5
2.5
3.5
4.5
6.5
: : : : :
6 6 6 6 6
or
or
or
or
or
without
blue
: : : : :
5
6
: : : : :
5
12
(Profile 6 ONLY)
6
7
8.5
11
Hide quick links:
Advertisement
