Table of Contents
Advertisement
2-WAY REMOTE
®
CONTROL ENGINE
STARTER
U S E R M A N U A L
Model RSS-5224
For all hybrid, gas- and diesel-
powered vehicles.
(FRANÇAIS AU VERSO)
C
S
P
ONSULT
AFETY
RECAUTION SECTION
.
BEFORE USING THIS PRODUCT
S
OME FEATURES MAY REQUIRE
(N
).
ADDITIONAL MATERIAL
OT INCLUDED
PATENT NOS
CAN 1.130.426
USA 4.345.554 - 5.614.883
- 5.617.819 - 5.673.017
AND OTHER PATENTS PENDING
All rights reserved © Astroflex Electronics 2007
July 2007
UBRSS5224
Advertisement
Table of Contents
Related Manuals for AstroStart RSS-5224
Summary of Contents for AstroStart RSS-5224
-
Page 1: Way Remote
2-WAY REMOTE ® CONTROL ENGINE STARTER U S E R M A N U A L Model RSS-5224 For all hybrid, gas- and diesel- powered vehicles. (FRANÇAIS AU VERSO) ONSULT AFETY RECAUTION SECTION BEFORE USING THIS PRODUCT OME FEATURES MAY REQUIRE... -
Page 2: Government Regulations
GOVERNMENT REGULATIONS This device complies with the requirements of Industry Canada (IC) - Management of Radio-frequencies, as specified in document CNR-210. Its use is authorized only on a no-interference, no-protection basis; in other words, this device must not be used if it is determined that it causes harmful interference to services authorized by IC. -
Page 3: Table Of Contents
The RSS-5224 offers a keyless entry feature allowing the user to operate the door locks as well as access to the trunk of the vehicle. These features are optional and may require additional material and/or wiring during installation. -
Page 4: Safety Precautions
SAFETY SEQUENCE FOR MANUAL TRANSMISSION VEHICLES Your remote starter was designed to force you to perform a series of actions that will ensure that the gearshift lever is in neutral position when you exit the vehicle. -
Page 5: Sequence Activated By Parking Brake
When you exit the vehicle, you need to prepare the remote starter for its next use. • If the vehicle is equipped with a manual transmission, make sure that the remote starter system has detected a valid safety sequence. •... -
Page 6: The Remote Control
THE REMOTE CONTROL The remote control can access four distinct remote starters. A maximum of four remote controls can be assigned to your vehicle. See your dealer for additional remote controls. NOTE: The range of your remote control can be affected by a weak battery, interference from nearby metal structures, hydro poles, or crowded parking lots. -
Page 7: Confirmations Emitted By The Remote
14 Battery charge indicator 15 Auxiliairy outputs status 16 Sentinel mode status 17 SECURITY SYSTEM STATUS 18 ULTRASONIC SENSOR 19 IGNITION STATUS SENSOR 20 TILT SENSOR 21 Remote starter status 22 HOOD STATUS 23 TRIGGERED ZONES 24 Valet mode status 25 Vehicle identification... -
Page 8: Ager
REMOTE CONTROL SETTING Certain functions on the remote may be set to your convinience. To access the remote control programming mode, press the seconds. The remote beeps once to endicate entering programming mode. EMOTE TRANSMITTER PROGRAMMING TABLE ARAMETERS Keyboard Un/Lock Mute Status confirmations Auxiliairy sensor icon... -
Page 9: Table Of Commands
Confirmations emitted by the vehicle are sent as soon as the command is received by the start module. In most cases, your remote starter will confirm that the command has been received, either by sounding the horn, the siren, or by flashing the parking lights. -
Page 10: Start Commands
START COMMANDS STARTING THE ENGINE To start engine, press button. The system automatically adjusts ignition duration for your type of vehicle; parking lights flash once (duration: four seconds) then stay on all the time when the engine is running. If more than one command is sent, each successive start command resets the runtime to the beginning, parking lights flash once to confirm command has been received and horn sounds once (programmable during installation) to let you know engine is already running. -
Page 11: Turbo Mode
Parking lights will stay on as long as the engine is running. RIGGER INPUT Your remote starter is equipped with a negative trigger (pulse) input. This input can be connected to another remote control device or to an AstroStart RST-2 timer output (optional), part number 310-903-502. - Page 12 STOP When engine is running on a remote start, you can turn it off by performing a stop command. This command also terminates panic mode and the alarm condition without disarming the security system. LOW TEMPERATURE MODE In Low Temperature (Sentinel) mode, system starts your engine automatically when the temperature falls below a preset level.
-
Page 13: Security System
SECURITY SYSTEM This section applies to an AstroStart safety system (optional) and should not be mistaken for the vehicle’s original system. On such a system, the remote can only warn of an alarm status (Alarm Link) (optional connections). The bi-directional remote control is in constant communication with your vehicle. Even if you do not ask for status, it will inform you by means of icons on your remote that a door has been opened for more than 5 minutes, that the engine has stopped, etc. - Page 14 Effect on rearming cycle These three zones prolong rearming cycle as long as they remain in violation. Activated by ignition key: Cancels rearming Activated by remote starter: No effect This zone cancels rearming completely. No effect...
- Page 15 Effect on rearming cycle These four zones prolong rearming cycle as long as they remain in violation. Activated by ignition key: Cancels rearming Activated by remote starter: No effect No effect button (see Table of Commands on page 9). button, which also disarms system. Pressing the with one soft chirp.
- Page 16 DURING DISARMING Indicator flashes code for last zone that generated the alarm condition. Code is shown when you press This code is repeated until you apply the brakes. The following table shows the meaning of zone codes (number of flashes). ZONE CODES FLASHES ZONE INDICATED...
-
Page 17: Lock/Unlock Commands And Alarm System Arming/Disarming
GLOSSARY IREN Siren has six different sounds, i.e., it chirps repeatedly and has six different melodies (only supplied with optional alarm kit). It chirps intermittently (short repeated chirps) during a pre-alarm and continuously during an alarm condition. It can confirm ARM and DISARM commands with short chirps; see table in CONFIRMATION section. This function is programmable as ACTIVE or INACTIVE during installation. -
Page 18: Trunk Release
UNLOCK / DISARM Press the button, doors are unlocked and alarm is disarmed, parking lights flash and siren chirps twice to confirm command has been received and that no alarm condition was generated during your absence. If there was a violation, confirmation is different (4 flashes or chirps) to warn you. See table of alarm codes to know which zone generated alarm condition. -
Page 19: Other Commands
ANTITHEFT (CIRCUIT DISABLER) Programmable as Active or Inactive during installation. Your Remote Starter is equipped with an antitheft system. This system, when enabled, consists of an output that controls a relay that cuts all circuits required to operate your vehicle (optional connection). -
Page 20: Car Finder
Start command ignored because key is in ignition (in “Run” position). Remote starter main switch is OFF. Runtime has elapsed. Remote starter attempted to start engine three times unsuccessfully. Remote starter sensed engine was already running. Engine is over-revving (RPM > 3000)(programmable at time of installation). -
Page 21: Code Learning Of Additional Transmitter(S)
Contact your service center. • Make sure that the parking brake is applied. • With gearshift in P, start vehicle with remote starter. • Remain in vehicle and be ready to apply brakes. • Without applying brakes, move gearshift out of P. -
Page 22: Gearshift Check Applicable To Manual Transmission Vehicles
Reversing polarity when boosting your battery could permanently damage your remote starter. Note: If alarm is armed when battery is disconnected, siren will sound when battery is reconnected if a zone is in violation. To avoid this, put system in Valet Mode before disconnecting battery...