Mitsubishi AJ71E71-S3 User Manual

Ethernet
Thank you for buying the Mitsubishi general-purpose
logic contrower MELSEC-A Series
Prior to use, please read both this manual and detailed
thoroughly and familiarize yourself with the product
MODEL
MODEL
CODE
1B NA -66687-C
01996 MITSUBISHI ELECTRIC CORPORATION
• SAFETY PRECAUTIONS
(Atways read before starting use)
When using Mitsubishi equipment,
associated manuals introduced in the manual
safety and handle the module properly
These precautions apply only to the installation of Mitsubishi equipment and
the wiring with the external device
module to be used for a description of the PLC system safety precautions
These • SAFETY PRECAUTIONS • classify the safety precautions into two
categories "DANGER" and "CAUTION'
; ODANGE R Procedures which may lead to a dangerous
causedeath or serious injuryif not carriedout properly
Procedures which may lead to a dangerousconditionand I
ACAUTION
1—-1 cause superficialto medium injury, or physical damage I
only, if not carried out properly
Dependi ng oncircumstance s, procedures
also be linked to serious results
In any case, it is important to follow the directions for usage
Store this manual in a safe place so that you can take it out and read it
whenever necessary Always forward it to the end user
[DESIGN PRECAUTIONS]
ACAUTION
• When laying the control wire or communication
or place near main circuit or power line
Keep them at least 100 mm (3 94 in ) away from such cables
Noise m cause erroneous o eration.
[INSTALLATION PRECAUTIONS]
ACAUTION
• Use the PLC in the environment given in the general specifications
section of the users rnanual to be used Using the PLC outside the range
of the general specifications may result in electric shock, fire, or
erroneous eration orm dama
MITSUBISHI
Interface
Module
User's Manual
(Hardware)
AJ71E71-S3
programmable
manual
AE71 S3-U-Hm-E
13J854
0006 MEE
thoroughly read this manual and
Also pay careful attention
Refer to the user s manual of the CPU
condition and I
indicated byACAUTION may
cable, do not bundle with
e or de rade the roduct.
[INSTALLATION PRECAUTIONS]
• Insert the tabs at the bottom Of the module into the mounting
unit If the module
breakdowns. or the module may fall off
• Tighten the screw within the range of specified torque
If the screws are loose, it may result in fallout, short circuits or malfunction
Tightening the screws to far may cause damage to the screw and/or the module.
resulting in fallout, short circuits or malfunction
• Make sure to switch all phases of the external power supply off before mounting or
removing the module
If you do not switch off the external power supply, it Will cause electric shock or
damage to the product
Do not touch the electronic parts orthe module conducting area directly
It m cause erroneous
[WIRING PRECAUTIONS]
• Perform correct pressure-displacement,
connections using the tools specified by the manufactures
may cause short circuits, fire or malfunction
• Attach connector to the module securely
• Be sure to fix communication
module by placing them in the duct or clamping them Cables not placed in the
duct or without clamping
pulled, Which may cause a module malfunction and cable damage
• Tighten the screw within the range of specified torque
If the screws are loose, it may result in short circuits or malfunction
Tightening the screws to far may cause damage to the screw and/or the module,
resulting in fallout, short circuits or malfunction
• Do not grab on the cable when removing the communication cable connected to
the module
When removing the cable with a connector, hold the connector on the side that is
connected to the module
When removing the cable connected to the terminal block, first loosen the screws
on the part that iS connected to the terminal block
Pulling the cable that is still connected
damage to the module or cable
• Solder coaxial cable connectors properly
Insufficient soldering may cause malfunction
• Be sure that cuttings, wire chips, or other foreign matter do not enter the module
Forei n matter ma start a fire or cause
The following product are available for this equipment
the
Refer to the table given below to choose suitable manuals
to
Detailed Manual
Manual
Ethernet Interface Module
I
Correspondence to EMC DIRECTIVE
To make the PLCs compliant with the EMC directive, refer to Chapter 3 "EMC AND
LOW-VOLTAGE DIRECTIVE* in the users manual (Hardware)
be used
• When the CPU module user's manual (Hardware)
"EMC AND LOW-VOLTAGE
High-Speed Accessing
Conforming to EMC Standards (18-68837) (optional)
ACAUTION
is not properly installed, it may
eration or failure.
ACAUTION
crimp-contact or soldering for external wire
cables or power supply
may hang or Shift, a1110Wingthem to be accidentally
to the module may cause a malfunction
an accident or erroneous
About the Manuals
name
Products
User's Manual
later
does not include Chapter 3
DIRECTIVE", refer to QnA Series CPU Compatible
Basic Base Unit — Additional
holes in the base
result in malfunctions,
Incorrect connection
cables leading frgm the
Of
ation.
Manual No
ei code
of SH-3598-C or
13J856
of the CPU module to
Explanation for Product