Yongnuo YN560-TX PRO User Manual
Speedlite transmitter
Hide thumbs
Also See for YN560-TX PRO:
- User manual (16 pages) ,
- Manual (29 pages) ,
- User manual (21 pages)
Advertisement
Quick Links
Advertisement
Related Manuals for Yongnuo YN560-TX PRO
Summary of Contents for Yongnuo YN560-TX PRO
- Page 1 YONGNUO YN560-TX Speedlite Transmitter LINK YNS60-TX LOCKON OFF 1 • User Manual...
- Page 3 Contents Introduction. Nomenclature Preparation Before Use Wireless Setting Wireless Flash Shooting C.Fn: Setting Custom Functions 9-10 Reference 11-12 Troubleshooting Guide. Specifications Read this instruction manual while also referring to the instruction manuals of your camera and Speedlite. Before using transmitter, read this instruction...
- Page 4 YN560TX II, with TTL/ high speed sync functions, its radio protocol achieves cross- brand compatibility • YN560-TX PRO (For N) can control, trigger YN200/YN862 series and the models which have been upgraded to the latest firmware such slave...
- Page 5 Nomenclature Radio transmission *The protective flim status lamp be torn out. Function button Function button LCD panel AF-assist beam emitter button Flash mode button :Test flash button Function button3 Select/Set button Function button4 Select dial Battery compartment cover Mounting foot lock lever ON : Power LOCK:...
- Page 6 Nomenclature LCD Display ZOOM(Slave unit) Gr: Group flash Custom functions enable Battery Flash mode Channel Firing group AF lamp enable Flash exposure ø.a il/128 or flash output • The display will show only settings currently applied. The functions displayed above function buttons 1 to 4, change according...
- Page 7 Preparation Before Use I.lnstall AA/LR6 batteries. I.Open the cover:Slide the cover down shown open battery compartment cover. 2.1nstall AA batteries: Install two AA batteries according to the + and - marks, rechargeable batteries of 1.2V can be used. 3.Close the battery: Close the battery Compartment cover and slide it up.
- Page 8 Preparation Before Use 3.Turning on the Power:Set the power switch to • The LCD panel illuminates. During wireless shooting, press transmitter' s test flash button to fire a test flash. About Lock Function By setting the power switch to <LOCK>, you can disable flash' s button and dial operations.
- Page 9 Wireless Setting Using a transmitter and a Speedlite compatible with radio transmission wireless shooting makes it easy to shoot with advanced wireless multiple flash lighting, in the same way as normal TTL autoflash shooting. Positioning and Operation Range (Example of wireless flash shooting) Before shooting, perform...
- Page 10 Wireless Flash Shooting I.Flash Group Setting • When <MENUI> is displayed, short press function button 3.TTL F.TTL <GR/PRE> select next flash group, long press this button select previous flash group Supports 6 groups(A/B/C/D/E/F). 2.Flash Mode Setting • Press < MODE >...
- Page 11 RF605 series support support CH16 the speedlite) support(Nee to set RF603(11) Series CHI- support (all DO not the flash out put on support group canfire) Support CH16 RF602-RX the speedlite) *Need to upgrade the latest firmware from YONGNUO wedsite.
- Page 12 C.Fn: Setting Custom Functions TEST OUTPUT Lock OX Press function button <C.FN> under MENU2 enter the custom function. Turn press the < > button to select the item to be set, and press to enter the setting. Press < SET > button to make a quick setting.
- Page 13 C.Fn: Setting Custom Functions c.Fn-02: AF Lamp ) O:ON (Enabled) AF-assist beam fired from the speedlite transmitter. C.Fn-03:4: (Backlit) When a button or dial is operated, LCD panel illuminates. You can change this illumination setting. O: 12sec 1: OFF 2: ON (Illumination always .Fn-04:O (LCDContrast) 0-9:...
- Page 14 Reference 1Shutter sync setting You can use front-curtain sync, rear-curtain sync or auto FP high speed sync. Refer to camera' s setting. Using high-speed sync need to set the camera to "AUTO FP" The relevant icons will be displayed on the LCD(FP). The maximum sync speed is 1/8000s or 1/4000s (depends on...
- Page 15 3.Clearing Transmitter Settings Press function buttons simultaneously 2 seconds longer, the transmitter settings are cleared. 4.Firmware Update I.Log in the YONGNUO official website (www.hkyongnuo.com) download firmware update software and the latest firmware. 2.Power off, use USB-Micro cable (do not include)connect to PC.
- Page 16 Troubleshooting Guide Power does turn • Make sure that batteries installed correct orientation. • Insert the mounting foot into the camera' s hot shoe all the way, slide the lock lever to the right, and secure the transmitter to the camera •...
- Page 17 Of our company.Further notice will not be given if the design and specifications change. The YONGNUO logo in this manual includes the registered trademark or trademark Of Shenzhen Yongnuo Photography Equipment Co.,...
Need help?
Do you have a question about the YN560-TX PRO and is the answer not in the manual?
Questions and answers