Advertisement
Quick Links
4b
Gdet
Power Equipment
Owner's
Manual
60"
MOWING
DECK
FOR
SUPER
GARDEN
TRACTORS
INSTALLATION
AND
MAINTENANCE
INSTRUCTIONS
Model
Number
190-325-100
Important:
Read Safety Rules and Instructions
Carefully
Thank you for purchasing an American-built product
CUB CADET CORPORATION
P.O. BOX 360930. CLEVELAND,
OHIO 44136
PRINTED
IN U.S.A
FORM NO. 772-9021
Advertisement
Related Manuals for Cub Cadet 190-325-100
Summary of Contents for Cub Cadet 190-325-100
- Page 1 MOWING DECK SUPER GARDEN TRACTORS INSTALLATION MAINTENANCE INSTRUCTIONS Model Number 190-325-100 Important: Read Safety Rules and Instructions Carefully Thank you for purchasing an American-built product CUB CADET CORPORATION P.O. BOX 360930. CLEVELAND, OHIO 44136 PRINTED IN U.S.A FORM NO. 772-9021...
- Page 2 WARRANTY Power Equipment Proper maintenance of your Cub Cadet equipment Is the owner's responsibillty. Follow the instructions Inyour owner's manual for cortect lubricants and maintenanceschedule. Your Cub Cadet dealer carries a complete line of quality lubrlcants and filters for your equipments engine, transmission, chassis and attachments.
- Page 3 e thro spindle, c enter m ounted 6 0inchrotary mower i sdesigned for useonCubCadettractors.Themower is quickdetachable bythe use of two spring loaded pins and two bayonet type hangers, KEEP AWAY! e mower extends beyondthetractorwheels to permitcuttingclose to trees,fences, shrubbery, buildings, drive and walkway edges, etc. DISCHARGE CHUTE MISSING...
- Page 4 personal safety. sure follow them. WARNING To reducethe potentialfor any injury,comptywith thefollowingsafetyinstructions.Failureto complywith the instructions may result in personal injury SAFE OPERATION PRACTICES FOR RIDING VEHICLES 10. Keep the area Of operation clear of all persons, Read the owner's manual carefully in its entirety before attempting to assemble or operate this particularly small children and pets.
- Page 5 setting parking brake, stopping engine and Keep all nuts, bolts, and screws tight to be sure removing key. the equipment is in safe working condition. 20. Do notstop or startsuddenlywhen goinguphillor Never store the equipment with fuel in the tank downhill.
- Page 6 ADJUSTING AND OPERATING Figure I 60" MOWER (RIGHT HAND SIDE) Adjustable Ljft Link Support Hanger Tractor Up Stop (Part of Tractor Frame) Lift Anchor Lock Tractor Lift Arms Lift Height Adjustment LEVEL ADJUSTMENT inch mower equipped with WARNING adjustable lift links and lift anchors. This feature attows...
- Page 7 CUTTING HEIGHT Mowing height adjustment is made by pinning WARNING gauge wheels and caster wheels into various adjustment holes for desired height of cut. NOTE: After rotary mower is installed on heights shown are approximate. tractor make sure tie rod and drag link of tractor steering system is not inteåered with PIN HERE by any part of the rotary mower.
- Page 8 NOTE When installing a new bett always check the condition of the pulleys and it they are not in satisfactory condition, replace them with new pulleys available at your authorized LIFT HEIGHT dealer, INDICATOR Figure 4 MOWER FLOAT Gauge wheels and caster wheels witt allow rmwer to "float"...
- Page 9 NOTE When greasing spindles use a sufficient amount to flush out the old grease and dirt. WOOD BLOCK IN POSITION GREASE LUBRICATION Use Cub Cadet 251H EP grease or equivalent. Figure 6 øø Figure 7 Idler Plvot Three Spindle Assemblies...
- Page 10 OIL LUBRICATION center blade pulley. Remove old V-belt from deck Use light weight lubricating oil. Use oil sparingly as housing.PlacenewV-beltaroundbladepulleyon left large accumulations of grease or Oit will collect dust. side ot deck, around bottom groove of center blade and tine particles of grass. pulley,andaroundspringloadedidlerpulley,pull V- belt againsttension01springloadedidler andwrap V-bett onto blade pulley on right side of deck.
- Page 11 the balance of cutting. This will give a better appear- ance to the lawn. Cut Gragg,. Do not cut the grass too short, as the mower will tend to scalp the grass. Short grass invites weed growth, and yellows quickly in dry weather. Mowingshouldbe donewiththe engineat futtthrottle.
- Page 12 ASSEMBLY iNSTRUCTlONS STEP 1. MOWER PREPARATION Attach mower support hangers to mower housing with two jam nuts (5/8") and two lock Attach deflector shield to the mower housing nuts (5/8") approximately 1 1/8 from roller with defector rod, deflector spring, cotter bracket to bottom of slot.
- Page 13 STEP 3. ATTACHING FRONT HANGER AND CENTER FRAME BAR CENTER FRAME BAR Engage the center frame bar with the cross shaft located under the tractor. Slide mower frame and front hanger under Liftframe onbothsides, a ssemble a djustable l inkinto tractor.
- Page 14 Figure 15 STEP 4. ATTACHING MOWER ASSEMBLY Start tractor engine raise tractor lift system to the up position. Move tractor to the left hand side mower deck turn tractor wheels left, tractor parking brake shut tractor engine. Roll mower deck under tractor position...
- Page 15 STEP 5- DRIVE BELT INSTALLATION PUSH PULL idler install mule drive V-belt, FORWARD ratchet handle must be pushed in and up to ¯ // AND lock handle in notch. This will provide necessary clearance for the mule drive V-belt to be slipped over the pulley flanges. Figure 19 NOTE Figure 17...
- Page 16 STEP 6. POSITION MOWER DECK WHEELS Start tractor engine raise mower deck. Reposition front rear gauge wheel the mower deck to forward position. Figure 21 1. Mower Deck 2. Front Gauge Wheel 3. Rear Gauge Whed...
Need help?
Do you have a question about the 190-325-100 and is the answer not in the manual?
Questions and answers