Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for NETGEAR DS104NA
Summary of Contents for NETGEAR DS104NA
-
Page 2: Start Here
Start Here ™ The NETGEAR Model DS104, Model DS106, Model DS108, and Model DS116 Dual Speed Hubs are network hubs that enable users to mix and match 10 and 100 megabit per second (Mbps) devices on the same network. This capability eliminates the high cost and complexity of separate network equipment for 10 and 100 Mbps users. -
Page 3: Package Contents
Package Contents Verify that the package contains the following items, as shown in the diagram: • DS100 Series hub • Wall mount hardware • Rubber footpads for tabletop installation • This installation guide • Warranty & Owner Registration Card • Support Information Card •... -
Page 4: Typical Applications
Typical Applications Refer to the following illustration when connecting your DS100 Series hub. The illustration shows a Model DS116 hub connecting users to a printer, servers, and a router. You can substitute a Model DS104, Model DS106, or Model DS108 hub, depending on the number of connections required. -
Page 5: Product Illustration
Product Illustration Front Panel of the Model DS104 Hub DUAL SPEED DUAL SPEED HUB DS104 100M On - Link Blinking = Receive 100 Mbps Normal/Uplink >40 10 Mbps Utilization% Front Panel of the Model DS106 Hub DS106 DUAL SPEED HUB 100M On - Link Blinking = Receive 100 Mbps... - Page 6 Model DS104, Model DS106, and Model DS108 LEDs Label Color Activity Description Power Green Power is supplied to the hub. Collision 10 Mbps Amber Data collision is occurring on the 10 Mbps network segment (some collisions are normal). 100 Mbps Amber Data collision is occurring on the 100 Mbps network segment (some collisions are normal).
-
Page 7: Rear Panel
Vista RJ-45 Network Ports with Built-in LEDs The front panel of the Model DS104 hub provides four vista RJ-45 network ports (six on the Model DS106 hub, eight on the Model DS108 hub, 16 on the Model DS116 hub). These standard RJ-45 connectors accept two-pair or four- pair Category 5 unshielded twisted pair (UTP) copper wiring (only two pairs are used). -
Page 8: Installation Procedures
Installation Procedures Prepare the Site Before you begin installing the hub, prepare the installation site. Make sure the site meets the operating environment requirements of the equipment. Characteristic Requirement Temperature Ambient temperature between 0 and 40 C (32 and 104 F). No nearby heat sources such as direct sunlight, warm air exhausts, or heaters. -
Page 9: Connect A Pc To The Hub
Caution: 100 Mbps operation requires the use of Category 5 UTP wiring with 100 Mbps certified connectors. NETGEAR highly recommends using Category 5 cable so your network can operate at either 10 or 100 Mbps. -
Page 10: Connect Hubs At 10/100 Mbps
Model DS116 hubs, or a combination of DS100 Series hubs can be daisy- chained together at 100 Mbps to support a growing number of PCs. For larger networks, use a 10/100 Mbps switch such as the NETGEAR Model FS104 switch, as shown in the illustration below. -
Page 11: Verify The Installation
Verify the Installation When installation is complete and power has been applied to the hub, the following conditions should exist: • Power LED is on. • Link LED on each connected port is on. • Utilization LEDs on the front panel are blinking when data is being received by any port in the hub, and the Link/Receive LED on the connected port is blinking when data is being received by that port. -
Page 12: Technical Specifications
Technical Specifications Model DS116 Model DS108 Model DS106 Model DS104 Specification Network Ports (RJ- Dimensions Width 11.3 in. 9.3 in. 9.3 in. 6.2 in. (286 mm) (235 mm) (235 mm) (158 mm) 1.1 in. 1.1 in. 1.1 in. 1.1 in. Height (27 mm) (27 mm) - Page 13 Replacment Power Adapter If, for any reason, the power adapter for any of the hubs fails, please contact NETGEAR immediately to order a replacement adapter. Use the following table to when ordering a specific power adapter. Order code DS104, DS106, DS108 PWR-0002-004 Power adapter (12 VDC, 1.2 A), North America...
- Page 14 In the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves the right to make changes to the products described in this document without notice. NETGEAR does not assume any liability that may occur due to the use or application of the product(s) or circuit layout(s) described herein.
- Page 15 NETGEAR, Inc. A Bay Networks Company 4401 Great America Parkway Santa Clara, CA 95054 USA Phone: 888-NETGEAR http://www.NETGEARinc.com *M-DS100NA-2*...