Draper CSP52500 Instructions Manual

49.3cc 500mm petrol chainsaw

Hide thumbs

page of 34

/ 34
Bookmarks

Quick Links

Download this manual

DRAPER

INSTRUCTIONS

FOR

49.3cc

500mm

Petrol

Chainsaw

Stock

No.75188

Part

No.CSP52500

IMPORTANT:

PLEASE

READ

THESE

INSTRUCTIONS

CAREFULLY

ENSURE

THE

SAFE AND

EFFECTIVE

USE OF

THIS

PRODUCT.

fata\.

GENERAL

INFORMATION

DRAPER

These instructions accompanying the product are the original instructions. This document is part of the product, keep it

for the life of the product passing it on to any subsequent holder of the product. Read all these instructions before

assembling, operating or maintaining this product.

This manual has been compiled by Draper Tools describing the purpose for which the product has been designed, and

contains all the necessary information to ensure its correct and safe use. By following all the general safety instructions

contained in this manual, it will ensure both product and operator safety, together with longer life of the product itself.

All photographs and drawings in this manual are supplied by Draper Tools to help illustrate the operation of the product.

Whilst every effort has been made to ensure the accuracy of information contained in this manual, the Draper Tools policy

of continuous improvement determines the right to make modifications without prior warning.

Need help?

Do you have a question about the CSP52500 and is the answer not in the manual?

Questions and answers

Summary of Contents for Draper CSP52500

Page 1 All photographs and drawings in this manual are supplied by Draper Tools to help illustrate the operation of the product.
Page 2 No part of this publication may be stored in a retrieval system or transmitted in any other form or means without written permission from Draper Tools Limited In all cases this copyright notice must remain intact.
Page 3 CONTENTS CONTENTS Page content Page TITLE PAGE INTRODUCTION REVISION HISTORY. UNDERSTANDING THIS MANUAL COPYRIGHT NOTICE CONTENTS CONTENTS GUARANTEE GUARANTEE INTRODUCTION SCOPE SPECIFICATION HEALTH & SAFETY INFORMATION GENERAL SAFETY INSTRUCTIONS FOR CHAINSAW 6-9A TECHNICAL DESCRIPTION IDENTIFICATION IOB-IOA UNPACKING & CHECKING PACKAGING. WHAT'S IN THE BOX?
Page 4 GUARANTEE GUARANTEE Draper tools have been carefully tested and inspected before shipment and are guaranteed to be free from defective materials and workmanship. Should the tool develop a fault, please return the complete tool to your nearest distributor or contact Draper Tools Limited, Chandler's Ford, Eastleigh, Hampshire, S053 IYF.
Page 5 SCOPE This 49.3cc petrol chainsaw is designed for general lopping, limbing and felling of trees and branches. SPECIFICATION Stock 75188 Part . CSP52500 Mass: Chainsaw without guide bar and chaint 5.2kg Volume: Fuel tank 0.56L Tank for chain lubricating 0.26L...
Page 6 HEALTH & SAFETY INFORMATION Have this tool repaired by a qualified person. This tool is designed to confirm to the relevant international and local standards and as such should be maintained and repaired someone qualified; using only original parts supplied by the manufacturer: This will ensure tool...
Page 7 HEALTH & SAFETY INFORMATION Close observation and inspection for dead or diseased wood and insecure limbs or branches must be carried out prior to any cutting. Dead wood can cause unexpected reactions during a routine felling Remove any scrub or other obstructions from the area to enable a quick escape route and ensure visibility of the chain is not impeded during cutting...
Page 8 HEALTH & SAFETY INFORMATION Felling Remove lower branches/limbs from the tree up to shoulder height When removing the lower branches ensure the operator is protected from kickback by using the tree stem for protection and keeping the guide bar out of line with the body (off set) Ensure there is sufficient fuel in the tank to safely complete the felling cut.
Page 9 HEALTH & SAFETY INFORMATION Maintenance Never modify the chainsaw in anyway. Always maintain the chainsaw in good working order regularly serviced by an authorised service agent. Ensure the handles remain clean and free from oil, fuel & moisture. Only use replacement parts supplied by the manufacturer.
Page 11 TECHNICAL DESCRIPTION IDENTIFICA TION Bar guard. Fuel tank cap Guide bar. Primer. Chain. Muffler (silencer) Wrap around handle. Bar locking nuts Chain brake lever (Front hand guard). Clutch cover. Recoil starter cord. Spiked bumper. Top cover screw. Clutch. Top cover. Drive sprocket Rear handle.
Page 12 It is not designed to store or transport petrol/petrol oil mix. The chemical and physical properties of petrol/petrol oil mix are such that the seals on this bottle may leak. Do not use this bottle for storage or transportation. Contact Draper Tools for suitable storage containers.
Page 13 Lay the contents out and check them against the parts shown below. If any part is damaged or missing; please contact the Draper Helpline (the telephone number appears on the Title page) and do not attempt to use the machine.
Page 14 ASSEMBLY WARNING: Do not start chainsaw before FIG. mounting and correctly adjusting the guide bar and chain ATTENTION: Saw chain is extremely sharp - wear gloves when handling chain. ATTACHING/ADJUSTING GUIDE CHAIN - FIGS. 1 - 9 Position the power head as shown (Fig. 1). Ensure the chain brake is disengaged.
Page 15 ASSEMBLY Position the guide bar @ on to the stud bolts Attach the Locate the chain tension adjuster pin into aperture on the guide bar. Slot all the drive links in to the guide bar groove. Mesh the drive links at the tip of the bar correctly round in to the nose sprocket teeth.
Page 16 Overheating will generate smoke. Only use oil specifically designed for lubricating chainsaw guide bars and chains (Draper stock No.58670 or 58677). Remove the chain oil tank cap @ by turning it anti-clockwise. With the aid of a funnel pour the lubricant into the oil tank, before replacing the cap firmly.
Page 17 OPERATION WARNING: Do not start the chainsaw until it is fully FIG. assembled, correctly adjusted and all functions controls are familiar. COLD STARTING ENGINE - FIGS. 12 - 15 Before starting, disengage the chain brake. Rest the chainsaw on a stable surface. Depress the stop switch to the "ON"...
Page 18 OPERATION & USE Grip the rear handle O, covering the throttle FIG. 15 trigger lockout with the palm of your hand. Pull the throttle to release throttle advance. The engine will now idle at normal tick over. If pausing for more than a few seconds, engage the chain brake.
Page 19 OPERATION & USE Warning: Chainsaws pose a very significant health and safety risk even to careful and trained operators. PERSONAL PROTECTIVE EQUIPMENT FIG.16 (PPE) - FIG. 16 Due to the nature and ferocity of a petrol driven chainsaw, no PPE can provide 100% protection against chainsaw cuts.
Page 20 OPERATION & USE HOLDING CHAINSAW FIG.17 - FIGS. 17 & 18 Do not be afraid to hold the chainsaw power head close in to the body. In this position the weight the saw will be easy to bear and in the event of a kickback will be more controllable.
Page 21 OPERATION & USE KICKBACK - FIG. Definition: KICKBACK Kickback: Rapid upward and/or backward motion ZONE of the chainsaw which can occur when moving saw chain near the tip of the guide bar contacts an object such as a log or a branch. Kickback is the most...
Page 22 OPERATION CHAIN BRAKE - FIG. FIG. 20 This machine is equipped with a mechanical chain brake. In the event of kickback, the chain brake guard STOP (ODO @ will be activated by the back of the operators hand and saw chain rotation will be stopped.
Page 23 OPERATION The direction can be changed from that intended factors such as wind, sloping terrain, tree growth (leaning, heavy limb structure one side and decay) etc. Failure to observe these factors or account them can result in severe injury or fatality. Plan an escape route and ensure all scrub, debris and undergrowth is cleared so an unimpeded...
Page 24 OPERATION 9.11 CROSS CUTTING/BUCKING FIG. - FIGS. - 27 TENSION Refer to general safety instructions for preparatory FACE and specific warnings. Regardless of the supporting method, when cross cutting the compression face of the timber must be initially cut followed by a secondary cut from the other side to meet completing the cut.
Page 25 OPERATION 9.13 CHAIN LUBRICATION - FIG. 28 Prior to use check chain oil distribution on a 25.1 piece of paper or cut timber. Observe spatter before continuing. If the chain is not sufficiently lubricated, check the oil tank level and/or increase the oil flow by rotating the setting screw anti-clockwise.
Page 26 MAINTENANCE Warning: Stop engine, allow to cool and engage the chain brake before carrying out maintenance adjustments to the machine. NOTE: Do not carry out repairs on the machine if you are not qualified to do so, with the exemption of the items listed in this maintenance section.
Page 27 MAINTENANCE 10.2 MAINTENANCE - FIG. FIG. Periodically clean the chain run groove and oil passages. Lubricate the sprocket wheel with bearing grease. Reverse the guide bar on a regular basis to ensure uniform bar wear. Burring of the guide bar rails is normal. Remove these burrs as appropriate with a flat file.
Page 28 MAINTENANCE 10.6 SPARK PLUG - FIGS. 34 & 35 FIG. 34 The spark plug should be replaced annually or if the chainsaw is experiencing starting problems. Remove the top cover to reveal the spark plug. Carefully pull off the spark plug HT lead. Using the box spanner supplied unscrew the plug If the electrodes are excessively soiled or are very...
Page 29 TROUBLESHOOTING WARNING: always stop the unit and disconnect the spark plug prior to performing any of the remedies, except where the remedy requires the engine to be running. Problem Probable cause Suggested remedy Engine will not 1. Fuel tank empty. 1.
Page 30 EXPLANATION OF SYMBOLS Danger of kickbacks. Single value noise marking. Kickbacks can cause (Maximum declared A-Weighted lethal wounds sound power level in decibels). Always wear personal protective Warning. equipment, ear defenders, face protection and helmet. Always wear gloves. Read the instruction manual Always wear safety footwear.
Page 31 DISPOSAL 13.1 DISPOSAL At the end of the machine's working life, or when it can no longer be repaired, ensure that it is disposed of according to national regulations. Contact your local authority for details of collection schemes in your area. In all circumstances: •...
Page 32 NOTES...
Page 33 IOTES...
Page 34 Sales Fax: (023) 8049 4209 General Enquiries: (023) 8026 6355 Service/Warranty Repair Agent For aftersales servicing or warranty repairs, please contact the Draper Tools Helpline for details of an agent in your local area. YOUR DRAPER STOCKIST KCMCO 1 0615...

This manual is also suitable for:

75188