Advertisement
Quick Links
Fan Installation and Operation
Manual
Linea / Hayra / Duo
Inbuilt Appliances
Supplied by:
Castworks Pty Ltd
12a Fiveways Boulevard
Keysborough VIC 3173
Warnings
Danger of Electrocution: All electrical work must be carried out by a qualified electrician.
Note: All electrical components should be installed in an airy location away from hot parts
Advertisement
Related Manuals for ADF Linea Series
Summary of Contents for ADF Linea Series
- Page 1 Fan Installation and Operation Manual Linea / Hayra / Duo Inbuilt Appliances Supplied by: Castworks Pty Ltd 12a Fiveways Boulevard Keysborough VIC 3173 Warnings Danger of Electrocution: All electrical work must be carried out by a qualified electrician. Note: All electrical components should be installed in an airy location away from hot parts...
- Page 2 For access to the fan/installing the fan assembly into the heater go to page 7. Note it may be easier to punch out the blanking plate before installing the heater – see page 9. Important! • Must be installed in accordance with electrical standard AS/NZS 3000. •...
- Page 3 Electric circuit layout with Wall Mounted Controller- Single sided Electric circuit layout with Wall Mounted Controller- Double sided Duo...
- Page 4 In the wiring diagrams above a connector or jumper is shown (Connector and Fuse) that must be in position AX, NOT position RA. That is, on the middle and RH pin, not the middle and LH pin. Position is marked as AX, and it should come like this from the factory but must be checked.
- Page 5 Power to Fan “Out” M - Active/Neutral Mains Supply “In” M – Neutral/Active Ph - Active (Phase) - Earth N - Neutral Polarity is - Earth interchangeable Mains Supply “In” Power to Fan “Out” Ph - Active (Phase) M - Active/Neutral N - Neutral M –...
- Page 6 Connect and test controller The controller must be positioned away from vents or the heat source, where it won’t get too hot and will read the ambient temperature. To turn on the fan, press the Standby (On) button bottom right. When the controller is first connected to the mains power supply, it will run the fan for 20 seconds as a self-test, then revert to the last setting speed or auto/manual setting.
- Page 7 INSTALLING THE FAN UNIT INTO HEATER Remove ash retainer by lifting slightly, rotating forward and the pulling out diagonally.
- Page 8 2. Remove the vermiculite from the base...
- Page 9 3. Undo the screws and remove the fan access cover. 4. Remove the bottom plate from the outer body – This can be easier by doing it from the underside – i.e., lay the heater carefully on its back after removing the bricks.
- Page 10 5. Pass the electrical cables x 2 through the gap and feed to the wall mount controller. 6. Now install the fan by slotting into the cut out, with the grill facing the front. Make sure that the glass tape is in position to dampen the vibrations.
- Page 11 Ensure there is NO Gap in the Top LH or RH side. Must be as below, no gap in the top, right!
- Page 12 7. Fix the fan in position with two screws on each end.
- Page 13 8. Fit the thermostat to the underside of Fan access cover. You may need to pry the tabs up slightly. Rotate the Thermostat under the tabs.
- Page 14 9. Wire up the fan to the controller and test before going further – see pages 2 to 6. 10. Replace the cover for Fan Access. 11. When inserting, ensure that the cabling is fixed in position so there is no way it can move to come in contact with the fan blades.
- Page 15 12. Screw the cover back into position. 13: Carry out the reverse of steps 1 to 3 to complete assembly.
- Page 16 Imported By: Manufactured by: Castworks, A.D.F. Lda. 12 Fiveways Boulevard, Z.I. Relvinha, Sarzedo A.P. 55 Keysborough, VIC 3173 3304-909 Arganil-Portugal...
Need help?
Do you have a question about the Linea Series and is the answer not in the manual?
Questions and answers