A2 Sb Ch Out; A3 Sw Att; A4 Subwoofer; A5 Tone Control - Denon AVR 1709 - AV Receiver Owner's Manual

ENGLISH
A2 SB CH OUT
(for Multi-channel sources
Select playback mode for surround back channels.
[Selectable items]
OFF
: No signal is played from the surround back
channels.
MTRX ON
: The surround channel signals undergo digital matrix
processing and are output from the surround back
channels.
z1
PL II x C
: Decoded in Dolby Pro Logic
surround back signal played.
z2
PL II x M
: Decoded in Dolby Pro Logic
surround back signal played.
z3
ES MTRX
: DTS signal played with digital matrix processing.
z4
ES DSCRT
: Signal included in DTS-ES Discrete 6.1-channel
sources played.
z1: This can be selected when "Surround Back Speaker" is set to
"2spkrs" at the "System Setup" – "Speaker Setup" setting
(vpage 23).
z2: This can be selected when "Surround Back Speaker" is set to
"2spkrs" or "1spkr" at the "System Setup" – "Speaker Setup"
setting.
z3: This can be selected when playing DTS sources.
z4: This can be selected when playing DTS sources including a
discrete 6.1-channel signal identification signal.
[STD]
Settings can also be made when
When using surround back speakers, adopt the following
settings.
q A dopt "7.1ch" for the Amp Assign setting.
• The default setting for the Amp Assign mode of AVR-1709 is
"ZONE2" .
w A dopt a setting other than "OFF" for the "SB CH OUT" setting
of "Surround Parameter" .
A2 SB CH OUT (for 2-channel sources)
Determine whether to use surround back speakers.
[Selectable items]
ON
: The surround back channel signal is played.
OFF
: The surround back channel signal is not played.

For details on adjusting individual parameters, see "Adjusting the parameters" (vpage 33).
) A3 SUBWOOFER ATT.
Attenuate subwoofer level when using EXT. IN mode.
[Selectable items]
ON
: The input from the subwoofer channel is attenuated.
OFF
: The input from the subwoofer channel is not attenuated.
Usually use in this mode.
Set this to "ON" if the subwoofer channel level seems too high when
II x Cinema mode,
playing audio signal.
II x Music mode,
A4 Subwoofer
Turn subwoofer output on and off.
[Selectable items]
ON
: The subwoofer is used.
OFF
: The subwoofer is not used.
A5 Tone Control
Turn tone adjustments on and off.
[Selectable items]
ON
: Allow tone adjustment (treble, bass).
OFF
: Playback without tone adjustment.
is pressed.
The tone cannot be adjusted when in the DIRECT mode.
NOTE
When the "Dynamic EQ" setting is "ON" , setting is not possible.
A6 Bass
Adjust low frequency range (bass).
[Variable range]
A7 Treble
Adjust high frequency range (treble).
[Variable range]
"Bass" and "Treble" can be set when "Tone Control" is set to "ON".
–6dB ~ 0dB ~ +6dB
~ ~
–6dB 0dB +6 dB
A8 MultEQ
Select the type of room correction desired from the following list:
[Selectable items]
Audyssey
: Optimize frequency response of all speakers.
Byp. L/R
: Optimize frequency response of speakers except front
L and R speakers.
Flat
: Optimize frequency response of all speakers to flat
response.
OFF
: Turn equalizer off.
Audyssey Audyssey Byp. L/R
OFF Audyssey Flat
Operating from the main unit or main remote
control unit
MULTEQ
Press .
• When "Audyssey", "Audyssey Byp. L/R" or "Audyssey Flat" is
selected, the Audyssey MultEQ indicator lights green.
• After running Auto Setup, if the Speaker Configuration, Distance,
Channel Level and Crossover Frequency have changed without
increasing the number of speakers measured, the Audyssey MultEQ
indicator lights red.
NOTE
• "MultEQ" can only be set when Auto Setup has been performed.
• "MultEQ" cannot be set in the following situations.
· If "Auto Setup" fails to be completed.
· After running Auto Setup, when the number of used speakers has
increased from the number of measured speakers.
• If the settings of speakers for which "None" has been determined
at "Auto Setup" are changed, "Audyssey" , "Audyssey Byp. L/R" and
"Audyssey Flat" cannot be selected. Either perform Auto Setup
again, or return to the setting after running Auto Setup with "System
Setup" – "Speaker Setup" – "Restore".
• When using headphones, "MultEQ" is set to "OFF".