Advertisement
Quick Links
Advertisement
Related Manuals for Tenda O8
Summary of Contents for Tenda O8
- Page 1 Tenda Quick Installation Guide 5GHz 23dBi llac Outdoor...
- Page 2 Package contents Center reflector panel x 1 Side reflector panel x 2 CPEx1 CPE seat Universal shaft Universal shaft fastener Ethernet port cover x 1 Metal strap xl (On the CPE seat) Quick Guide POEinjector x 1 Power adapter x 1 Screw Quick installation guide x 1...
-
Page 3: Get To Know Your Device
Get to know your device PoE/LAN LED indicator RESET button LEDI, LED2 and LED3 indicators PoE/LAN port Port/Button Description Reset button. When the CPE is operating normally, hold down the button for about 8 seconds and release it when all LED indicators light up. - Page 4 Assemble install Stepl: Assemble the CPE. O Align the two bolts on one side ofthe center reflector panel with the long screw holes (the larger end) on the side reflector panel. Slide the center and side reflector panels in the opposite direction until the bolts fit into smaller end.
- Page 5 Tips You may have to prepare a Phillips screwdriver, gloves and other tools to assemble and install the CPE. O Repeat O to fix another side reflector panel. O Insert the CPE into the CPE seat from the front side of the center reflector panel.
- Page 6 Remove the Ethernet port cover from the CPE seat. Align the slots of the CPE seat with the abutted edges of the center reflector panel and side reflector panels, and four hooks of the CPE seat with the four slots of the center reflector panel.
- Page 7 O Press the CPE seat to fix it on the center reflector panel. O Direct the CPE seat at the universal shaft fastener, and screw the universal shaft fastener to fix the CPE (Ensure an appropriate tightness for you to adjust the orientation of the CPE later).
- Page 8 To prevent the deformation of the reflector panels and decreasing of bridging quality, DO NOT face the reflector panels down and put them on a desk or a horizontal plane while and after fixing the CPE seat. The placement shown above is prohibited. Adjust the orientation of the CPE to the horizontal with the bubble level .
- Page 9 Scenario 1: CCTV surveillance or point to point data transmission -Ü- Tips: At least two CPEs are required for bridging. O Insert the CPE into the CPE seat from the front side of the center 1. Set up the CPEs (AP mode + Client mode) 1.
-
Page 10: Manual Bridging
Slot Option 2: Manual bridging Stepl: Place two CPEs next to each other. O Direct the CPE seat at the u shaft fastener to fix the CPE g to the application scenario you need. adjust the orientation of the the screw O Connect the POEinjector to universal shaft... - Page 11 Slots Bubble level Step3: Set CPEI to AP mode. O Start a web browser on the computer and visit 192.168.2.1. Enter the login user name and password and click Login. O e 192.168.2.1 -renda 08V1.o Hooks Cetault username: oclmir Jctault admin English Ethernet...
- Page 12 O Customize your SSID (WiFi name)and Key (WiFi password), select a Channel, a Security Mode (WPA2-PSK is recommended), and an Encryption Algorithm. Click Next. Record the SSID and Key for later setup. Set up your here down password, Tenda_123456 Cha n nel 3615180MHz) SecurityMode vv'PA2-PSK...
- Page 13 Click "Scan", and select the wireless network you want to connect, user name and password and click Login. and click "Next" Scan Scan_again Upstream AP Tenda_123a56 O e 192.168.2.1 Tenda So-lal Select Channel MAC Address Security Mode cg 3A WPA2-PSK,AES Tenda_123456 08V1.o...
- Page 14 Quick Setup Client O Select the SSD of the ISP(Internet Service Provider)hotspot, which Set the IPaddress to an unused P address belonging to the network segment of upstreamAP. is Tenda 123456 in this example, and click Next. IP Address 192.16B 2.100...
- Page 15 2. Application scenario O Connect the CPEs with the LEDI, LED2 and LED3 indicators solid on (AP mode - the transmitting end) to the switch which is connected an NVR (Network Video Recorder). O Connectthe CPEswith the LEDI, LED2and LED3indicatorsblinking (Client mode —...
- Page 16 Use the included power adapter to connect the POE injector to a power source. O WISP Connect a computer to the LAN port of the POEinjector. O P2MP In O Router point Tenda POE injector POE injector Tips: If the login page access...
- Page 17 Quick Setup Client Set the IPaddress to an unused P address belonging to the network segment of upstreamAP. O Select the SSD of the ISP(Internet Service Provider)hotspot, which is Tenda 123456 in this example, and click Next. IP Address 192.16B 2.100 O Click Save, and wait until the CPE reboots to activate the settings.
- Page 18 You can set up pur wireless network name andwireless password here such as 192.168.2.X (X ranges from 2 - 254). "kite down your wireless password. Restore the CPE to factory settings, and try again. Tenda 888888 (WiFi Name) (5180MHz) Onannel...
- Page 19 O Set an IPaddress belonging to different network segment as O Select WISP, and click Next. that of your ISP hotspot. For example, if the IP address of your ISP hotspot is 192.168.2.1, you can set this CPE's IP address to 192.168.X.1 (X ranges from O to 254 excluding Then click...
- Page 20 O Select the SSD of the ISP(Internet Service Provider)hotspot, which Ensure that the IP address of the computer is set to an unused one, is Tenda 123456 in this example, and click Next. such as 192.168.2.X (X ranges from 2 - 254).
- Page 21 Staten-lent This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
- Page 22 Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user' s authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Operating frequency: 5150-5250MHz, 5725-5850MHz...
- Page 23 RJ45 cable. Declaration of Conformity Hereby, SHENZHEN TENDA TECHNOLOGY CO., LTD. declares that the radio equipment type 08 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity...
- Page 24 E-mail: support@tenda.com.cn Copyright 0 2021 Shenzhen Tenda Technology Co., Ltd. All rights reserved. Tenda is a registered trademark legally held by Shenzhen Tenda Technology Co., Ltd. Other brand and product names mentioned herein are trademarks or registered trademarks of their respective holders.
Need help?
Do you have a question about the O8 and is the answer not in the manual?
Questions and answers