1. Manuals
  2. Brands
  3. Tecson Manuals
  4. Measuring Instruments
  5. LX-Q-NET
  6. Installation instructions manual

Tecson LX-Q-NET Installation Instructions Manual

Electronic tank monitoring devices with data messaging
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Installation Instructions
Electronic tank monitoring devices with data messaging
Tankspion LX-NET
Tankspion LX-GSM / LX-Q-GSM
Tankspion LX-EDGE / LX-Q-EDGE
03-2025
LX-(Q)-NET / GSM / EDGE
Techn. Documentation
and
/ LX-Q-NET
/ e-litro T NET
/ e-litro T GSM
Content:
For LX-(Q)-Edge
everything is analogous as with LX-(Q)-GSM
For e-litro T NET
everything is analogous as with LX-NET
For e-litro T GSM
everything is analogous as with LX-GSM
Firmware since 06-2023: Version V8.0(+)
Techn. Docum. + Installation
Page:
2
3
3
5
6
7
9
10
10
11
12
14
16
16
17
17
P. 1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the LX-Q-NET and is the answer not in the manual?

Questions and answers

Related Manuals for Tecson LX-Q-NET

Summary of Contents for Tecson LX-Q-NET

  • Page 1: Table Of Contents

    Installation Instructions Techn. Documentation Electronic tank monitoring devices with data messaging Tankspion LX-NET / LX-Q-NET / e-litro T NET Tankspion LX-GSM / LX-Q-GSM / e-litro T GSM Tankspion LX-EDGE / LX-Q-EDGE Content: Page: GENERAL MOUNTING INSTRUCTIONS MOUNTING OF LEVEL PROBE...

  • Page 2: General

    GENERAL The electronical tank content display device of LX-Serie is to be used for monitoring of tank levels in pressureless liquid tanks. This documentation is to be used for the LX-(Q)-Edge, LX-(Q)-GSM and LX-NET / LX-Q-NET. For the ‘Edge’ devices, everything is the same as for the ‘GSM’ version. Beside the liter monitoring several other functions are available, in most cases with an extra module or adaptor.

  • Page 3: Mounting Instructions

    MOUNTING INSTRUCTIONS Only qualified persons are allowed to install the measuring probe and to connect the display de- vice. Follow the regulation for each liquid, especially for the risk of water pollution and for flam- mable liquids. Condition for proper operation of measuring device is a professional installation. Follow the tech- nical rules for planning, construction and operation of the entire facility.
  • Page 4 - in manhole pit (buried tanks) - in damp locations. The probe box must be wa- tertight and ventilated (for pressure balance of the hydrostatic level probe). Tecson part no.: 12080 P. 4 LX-(Q)-NET / GSM / EDGE Techn. Docum. + Installation 03-2025...

  • Page 5: Electric Installation

    ELECTRIC INSTALLATION Interconnection of measuring probe to display device Probe supply: Low-voltage DC Connection: Connect the 2-wire probe cable as follows: Refer to the figure on the Red(+) => clamp 1 , Black (-) => clamp 2. following page. Air capillary: The air capillary must have ventilation to atmosphere.

  • Page 6: Connection Clamps

    CONNECTION CLAMPS If LX-GSM and LX-NET Relay connection: The LX-GSM and LX-NET devices do have a double output relay. By this relay two separate elec- tric circuits can be switched simultaneously, e.g. a signalling device on/off and an electric valve off/on too. Under initial conditions the relay contacts 7-8 are closed and relay contacts 9-10 are opened.

  • Page 7: Device Messages (Sms)

    For LX-(Q)-GSM: Clamps and SIM and push-buttons on LX-GSM device DEVICE MESSAGES / DEVICE PARAMETERS If the device is connected to OilView, also with the use of the app, everything is configured and managed in the OilView system, including the alarm forwarding. In this case, there is no need for manual configuration using SMS commands.
  • Page 8 For LX-(Q)-NET: LX-NET connection clamps: Probe | Serial-Link-In | Digital-In (Alarm) Pushbuttons Relay conttact pairs 230V supply LX-Q-NET connection clamps Alarm input | Pushbuttons Measuring probes 1 ( to 4 ) 230V supply P. 8 LX-(Q)-NET / GSM / EDGE Techn.

  • Page 9: Initial Setup

    INITIAL SETUP The initial setup is carried out after completed mounting. Determine the tank data and enter them into the mode: You find 3 push buttons (blue) on the PCB positioned between the connection clamps. Ø Press ENTER => Device enters the setup mode Displayed step „1.

  • Page 10: Function Check

    FUNCTION CHECK After fueling or once a year please check if the displayed liters are correct. MAINTANCE It is recommended to check once year if the displayed liters are correct. If there is a suspicion of a discrepancy, for a simple check lift the level probe by the cable so that the probe is above the liquid level.

  • Page 11: Network Connection

    For LX-NET / LX-Q-NET : NETWORK CONNECTION Netzwork connection: The LX-(Q)-NET device has a directly connectivety to LAN/Ethernet network with 10 / 100 Mbit TCP/IP protocol. Inside the housing you find the RJ45 jack for connecting a CAT-5 network cable. The plug of the network cable has to be pushed through the inlet at bottom side of the housing.

  • Page 12: Browser Access

    BROWSER ACCESS Show content in browser: Entering the IP address in your browsers address line the device will be called: P. 12 LX-(Q)-NET / GSM / EDGE Techn. Docum. + Installation 03-2025...
  • Page 13 Parameter setup via Browser: Clicking the ’CONFIG’ button opens a next page in the browser. Here you can setup serveral parameters for the device. Password: The inital passwort for config access at the device is: tank The password is changeable here. It is recommended to store an individual device password.

  • Page 14: Error Codes

    ERROR CODES Error code Meaning Error E 1 Invalid value setup. Error E 2 Measuring value of the probe is too low ! If current is less than 3.5 mA => Probe error. Measuring value too high for probe offset/zero calibration. The probe must not be Error E 3 plunged! A probe’s current above 4.5 mA is invalid as zero point.
  • Page 15 LX-(Q)-NET: Error-Messages at network communication Error N1 No network communication. A problem with the internal network module. The device automatically executes an internal ’Reset’ and retrys initial communications. Try disconnection of network plug, wait… and remount the network plug. Error N2 Error at the network comm..

  • Page 16: Technical Data

    TECHNICAL DATA Display device Supply voltage: Type AC : 230 V 50 Hz (standard) Type DC : 12V or 24V version Power consumption: <= 4 VA, typically 2 VA 4 - 20mA; U ca. 20V Measuring input: Resolution 12 Bit Accuracy: ±...

  • Page 17: Accessories

    Content management of oil tanks Refer to by the tecson app. https://www.tecson.de/oil- smartview-app.html LABELING The manufacturer TECSON declares the compliance with the valid safety and test guidelines (CE Declaration). For Conformity Declaration refer to website www.tecson.de at menu item ‘Documentation’. Disposal: After dismantling all parts need to be disposed properly with regard to their material.
  • Page 18 P. 18 LX-(Q)-NET / GSM / EDGE Techn. Docum. + Installation 03-2025...

Table of Contents