Echo CS-370 Instruction Manual page 16

Ignition switch
Ignition switch
Start / Run
Start / Run
Push
Push
Throttle latch
Throttle latch
Starter handle
Starter handle
Unlock chain brake
Unlock chain brake
Choke control knob
Choke control knob
Unlock chain brake
Unlock chain brake
Choke control knob
Start / Run
Push
CS-370
Throttle latch
CS-370
CS-370
Chain brake
Chain brake
Throttle trigger lockout
Throttle trigger lockout
Throttle trigger
Throttle trigger
Chain brake
Open choke
Open choke
Ignition switch
Throttle trigger lockout
Open choke
Throttle trigger
WHEN THE ENGINE IS HARD TO
WHEN THE ENGINE IS HARD TO
START
START
CAUTION
CAUTION
Make sure the bar and chain are free from any
Make sure the bar and chain are free from any
obstruction when starting the chain saw.
obstruction when starting the chain saw.
• Move chain brake lever fully forward to lock chain brake
• Move chain brake lever fully forward to lock chain brake
before starting.
before starting.
• Press throttle trigger lockout down while grasping throttle
• Press throttle trigger lockout down while grasping throttle
trigger and push in throttle latch.
trigger and push in throttle latch.
• Move ignition switch to "RUN" position.
• Move ignition switch to "RUN" position.
• Securely hold the chain saw as shown and pull starter
• Securely hold the chain saw as shown and pull starter
handle.
handle.
• When engine starts, immediately squeeze throttle
• When engine starts, immediately squeeze throttle
trigger, to release throttle latch.
trigger, to release throttle latch.
CAUTION
CAUTION
1. When using throttle latch for starting, keep the
1. When using throttle latch for starting, keep the
brake in lock position.
brake in lock position.
2. After starting the engine, squeeze throttle
2. After starting the engine, squeeze throttle
trigger slightly to release throttle latch.
trigger slightly to release throttle latch.
3. Do not increase engine speed while chain brake
3. Do not increase engine speed while chain brake
is locked.
is locked.
CAUTION
CAUTION
The chain will attempt to rotate when engine is
The chain will attempt to rotate when engine is
started with throttle latch engaged. After engine
started with throttle latch engaged. After engine
starts, release throttle trigger to idle engine,
starts, release throttle trigger to idle engine,
otherwise brake damage may occur. Never use
otherwise brake damage may occur. Never use
throttle latch for cutting. Use it only when starting
throttle latch for cutting. Use it only when starting
the engine.
the engine.
WHEN THE ENGINE IS HARD TO
WHEN THE ENGINE IS WARM
START
WHEN THE ENGINE IS WARM
• Move chain brake lever fully forward to lock chain
• Move chain brake lever fully forward to lock chain
CAUTION
brake before starting.
brake before starting.
Make sure the bar and chain are free from any
• Confirm there is fuel and chain oil in the tanks.
• Confirm there is fuel and chain oil in the tanks.
obstruction when starting the chain saw.
• Move ignition switch to "RUN" position.
• Move ignition switch to "RUN" position.
• Securely hold the chain saw as shown and pull starter
• Securely hold the chain saw as shown and pull starter
• Move chain brake lever fully forward to lock chain brake
handle.
handle.
before starting.
• Choke may be used if necessary, but be sure to push
• Choke may be used if necessary, but be sure to push
• Press throttle trigger lockout down while grasping throttle
it back on first firing sound.
it back on first firing sound.
trigger and push in throttle latch.
• Move ignition switch to "RUN" position.
NOTE
NOTE
• Securely hold the chain saw as shown and pull starter
If engine does not start after 5 pulls, use cold start
If engine does not start after 5 pulls, use cold start
handle.
procedure.
procedure.
• When engine starts, immediately squeeze throttle
trigger, to release throttle latch.
16
16
16
CAUTION