Echo CS-370 Instruction Manual
  1. Manuals
  2. Brands
  3. Echo Manuals
  4. Chainsaw
  5. CS-370
  6. Instruction manual

Echo CS-370 Instruction Manual

Echo chain saw
Hide thumbs Also See for CS-370:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Operator's Manual, Instruction Manual
x7722271404 / x772000164

Instruction Manual

The muffler or catalytic muffler and surrounding cover may become extremely hot.
Always keep clear of exhaust and muffler area, otherwise serious personal injury may
occur.
The engine exhaust from this product contains chemicals known to the State of California to cause
cancer, birth defects or other reproductive harm.
Users of this equipment risk injury to themselves and others if the unit is used
improperly and/or safety precautions are not followed. ECHO provides an operator's
manual and a safety manual. Both must be read and understood for proper and safe
operation. Failure to do so could result in serious injury.
Specifications, descriptions and illustrative material in this literature are as accurate as known at the time
of publication, but are subject to change without notice. Illustrations may include optional equipment and
accessories, and may not include all standard equipment.
X7503251406
© 08/2013 ECHO Inc.
CS-370
CHAIN SAW
Burn Hazard

Advertisement

Table of Contents
loading

Related Manuals for Echo CS-370

Summary of Contents for Echo CS-370

  • Page 1: Instruction Manual

    Users of this equipment risk injury to themselves and others if the unit is used improperly and/or safety precautions are not followed. ECHO provides an operator’s manual and a safety manual. Both must be read and understood for proper and safe operation.

  • Page 2: Table Of Contents

    Technical Data ..................................38 Warranty Statements ................................39 Notes ....................................41 Servicing Information ................................47 Parts/Serial Number ..............................47 Service..................................47 Echo Consumer Product Support ..........................47 Warranty Registration ..............................47 Additional or Replacement Manuals ..........................47 X7503251406 © 08/2013 ECHO Inc.

  • Page 3: Packing List

    After opening the carton, check for damage. Immediately notify your retailer or ECHO dealer of damaged or missing parts. Use the packing list to check for missing parts.

  • Page 4: Safety

    The tip guard device is not installed on the guide bar when you purchase your ECHO chain saw. The tip guard can be used in a Rotational kickback majority of cutting operations, and is especially recommended for beginners, homeowners, or chain saw novices.

  • Page 5: Correct Use Of Chain Brake

    Immediately release the throttle trigger. Do not allow the saw to tip forward in order to avoid damage to the chain. If the chain does not stop immediately, return the saw to your authorized ECHO dealer for repair. Note: •...
  • Page 6 13. When cutting a limb that is under tension, be alert for spring-back so that you will not be struck when the tension in the wood fibers is released. X7503251406 © 08/2013 ECHO Inc.
  • Page 7 18. When transporting your chain saw, use the appropriate guide bar scabbard. 19. Spark arrestor mufflers approved to SAE Standard J335 are standard on ECHO chain saws to reduce the possibility of forest fires. Do not operate the chain saw with a loose or defective muffler. Do not remove the spark arrestor screen.

  • Page 8: Personal Condition And Safety Equipment

    Breathing Protection Wear a facemask to protect against dust. Hearing Protection ECHO recommends wearing hearing protection whenever unit is used. Proper Clothing Wear snug fitting, durable clothing; • Pants should have long legs, shirts with long sleeves.
  • Page 9 ECHO does not recommend the use of ECHO products by anyone who has a pacemaker.
  • Page 10 This unit is not insulated against electrical current. Never touch wires directly or indirectly, otherwise serious injury or death may result. Do not operate this product indoors or in inadequately ventilated areas. Engine exhaust contains poisonous emissions and can cause serious injury or death. X7503251406 © 08/2013 ECHO Inc.

  • Page 11: Symbols And Signs

    Throughout this manual and on the product itself, you will find safety alerts and helpful, informational messages preceded by symbols or key words. The following is an explanation of those symbols and key words and what they mean to you. X7503251406 © 08/2013 ECHO Inc.

  • Page 12: Emission Control (Exhaust / Evaporative)

    The 50 or 300 hour emission compliance period is the time span selected by the manufacturer certifying the engine emissions output meets applicable emissions regulations, provided that approved maintenance procedures are followed as listed in the Maintenance Section of this manual. X7503251406 © 08/2013 ECHO Inc.

  • Page 13: Description

    Locate the safety decal(s) on your unit. Make sure the decal(s) is legible and that you understand and follow the instructions on it. If a decal cannot be read, a new one can be ordered from your ECHO dealer. See PARTS ORDERING instructions for specific information.
  • Page 14 24. Front handle (for the left hand) - Support handle located at the front of the engine housing. 25. Cylinder cover - The cooling airflow grill. It covers the cylinder, spark plug and silencer. CHAIN SAW TERMS 1. Chain Brake - Stops the saw chain. 2. Drive Sprocket - Drives saw chain. X7503251406 © 08/2013 ECHO Inc.

  • Page 15: Preparation For Use

    (C). 3. Remove sprocket guard nuts (D) and remove sprocket guard (C). 4. Remove guide bar and saw chain if necessary. Note: See “Maintenance and Care” section for guide bar/saw chain maintenance procedures. X7503251406 © 08/2013 ECHO Inc.
  • Page 16 Always loosen sprocket guard nuts before turning the chain tension Unlock chain brake adjuster, otherwise the sprocket guard and tensioner will be damaged. 1. Remove air cleaner cover and disconnect spark plug lead. 2. Loosen sprocket guard nuts. X7503251406 © 08/2013 ECHO Inc.
  • Page 17 Tighten guide bar nuts to 20 to 23 N•m (175 to 200 in•lbf). DO NOT over-tighten nuts. Damage to saw may result. 6. Assemble components in reverse order. 7. Keep chain properly tensioned at all times. Note: All chains require frequent adjustments. X7503251406 © 08/2013 ECHO Inc.

  • Page 18: Operation

    OPERATION Fuel Alternative fuels, such as E-15 (15% ethanol), E-85 (85% ethanol) or any fuels not meeting ECHO requirements are NOT approved for use in ECHO 2-stroke gasoline engines. Use of alternative fuels may cause performance problems, loss of power, overheating, fuel vapor lock, and unintended machine operation, including, but not limited to, improper clutch engagement.

  • Page 19: Chain Lubricant

    • Do not use used or reclaimed oil to avoid various oiler problems. • Use ECHO bar and chain oil. • When ECHO bar and chain oil is not available: Use motor oil, etc. Fuel tank cap Oil tank cap •...

  • Page 20: Winter Operation

    QR code. Make sure the bar and chain are free from any obstruction when starting the chain saw. Chain brake 1. Move chain brake lever fully forward to lock chain brake before starting. X7503251406 © 08/2013 ECHO Inc.

  • Page 21: Starting Hard To Start Engine

    3. Move ignition switch (A) to “RUN” position. 4. Securely hold the chain saw as shown and pull starter handle. 5. When engine starts, immediately squeeze and then release throttle trigger, to release throttle lock button. X7503251406 © 08/2013 ECHO Inc.

  • Page 22: Starting Warm Engine

    Note: If engine does not start after 5 pulls, use cold start procedure. Note: Do not increase engine speed while chain brake is locked. Severe brake damage will result. X7503251406 © 08/2013 ECHO Inc.

  • Page 23: Running

    2. Move ignition switch (A) down to “stop” position. Note: If engine does not stop, pull choke control knob out fully to stop engine. Return the unit to your authorized ECHO dealer to check and repair stop switch before starting the engine again.

  • Page 24: Chain Lubrication Test

    • This chain saw is designed for cutting wood or wood products. Do not cut solid metal, sheet metal, plastic or any non-wood materials. • Read the ECHO “CHAIN SAW SAFETY MANUAL” included with your chain saw for additional cutting and safety instructions.
  • Page 25 Note: Some material may adversely affect the housings of your ECHO chain saw.(Example: Palm Tree Acid, fertilizer, etc.) To avoid housing deterioration, carefully remove all packed saw dust around clutch and guide bar area and wash with water.
  • Page 26 To cut the trunk, use the bucking and two-cut sequence shown. The first cut should be no deeper than one-third the trunk diameter. When the bar nose hits another tree, etc. X7503251406 © 08/2013 ECHO Inc.

  • Page 27: Chain And Guide Bar Combination

    Chain and guide bar gauge size must be identical. Use Bar/Chain combinations shown in table above. If your tip guard is damaged or lost, contact your Echo dealer for a replacement. For the name of the Echo dealer nearest you, Call: 1-800-432-ECHO (3246) or on the web at www.echo-usa.com.

  • Page 28: Maintenance

    If you are unsure or are not equipped with the necessary tools, you may want to take your unit to an ECHO Service Dealer for maintenance. To help you decide whether you want to DO-IT-YOURSELF or have the ECHO Dealer do it, each maintenance task has been graded.

  • Page 29: Carburetor Adjustment

    This engine has been factory adjusted to maintain satisfactory starting, emission, and durability performance up to 1,100 feet above sea level (ASL) (96.0 kPa). To maintain proper engine operation and emission compliance above 1,100 feet ASL the carburetor may need to be adjusted by an authorized ECHO service dealer.

  • Page 30: Air Filter

    1. Using a wire bent into the shape of a hook, pull filter out through gas port, and inspect filter. 2. When the filter is dirty, replace it. 3. When the inside of the fuel tank is dirty, rinse the tank out with gasoline to clean it. X7503251406 © 08/2013 ECHO Inc.

  • Page 31: Automatic Oiler

    2. Clean the groove (A) of the guide bar with a small screwdriver. 3. Clean oil holes (B) with a wire. 4. Invert guide bar periodically. 5. Clean the bar mount area before installing of the bar. X7503251406 © 08/2013 ECHO Inc.

  • Page 32: Sprocket

    USDA Forest Service Regulation SAE J335. Check with your local or state authorities for specific regulations in your area. Failure to follow these requirements is a violation of the law. X7503251406 © 08/2013 ECHO Inc.

  • Page 33: Spark Arrestor Screen

    11. Install guide bar and chain. Adjust chain tension. 12. Start engine and check for exhaust leaks between muffler and cylinder head. Stop engine if leak is found and correct problem before operating chain saw. X7503251406 © 08/2013 ECHO Inc.

  • Page 34: Setting The Saw Chain

    • For setting saw chain, round file (4.0 mm dia. 5/32 in.) and flat file are used. 30° • Push file as shown. Keep this angle • To keep correct position and correct angle, use a file holder. • Hold the file horizontally. 90° X7503251406 © 08/2013 ECHO Inc.
  • Page 35 • If the saw chain becomes soiled with resin, for instance, clean 0.64 mm (0.025 in.) it with kerosene and soak in it oil. To sharpen other chains, follow chain manufacturer’s instructions. Parallel Depth gauge X7503251406 © 08/2013 ECHO Inc.

  • Page 36: Troubleshooting

     See your Echo dealer doesn’t start Stop switch off  Turn switch to ON  Spark at end of See your Echo dealer  No spark Electrical problem plug wire Interlock switch See your Echo dealer Spark gap incorrect Adjust to .65mm (0.026 in.)...

  • Page 37: Storage

    Note: • For future reference, you should keep this Instruction manual and the Safety manual. • If this Instruction manual or the Safety manual has become illegible or is lost, please contact your ECHO dealer, or go to www.echo-usa.com. X7503251406...

  • Page 38: Technical Data

    NGK BPM8Y Fuel tank capacity 410 mL (13.9 US. fl. oz.) 50 : 1 ratio with ECHO Power Blend X™, ISO-L-EGD (ISO/CD 13738) and JASO Fuel M345-FD two-stroke, air-cooled engine oil. Use 89 octane unleaded. Do not use fuel containing methyl alcohol, more than 10 % Gasoline ethyl alcohol or 15 % MTBE.

  • Page 39: Warranty Statements

    PRODUCT SOLD IN USA AND CANADA BEGINNING 01/01/2010 ECHO'S RESPONSIBILITY THIS LIMITED WARRANTY IS ONLY APPLICABLE TO ECHO PRODUCTS SOLD BY AUTHORIZED ECHO DEALERS. IT IS EXTENDED TO THE ORIGINAL PURCHASER ONLY, AND IS NOT TRANSFERABLE TO SUBSEQUENT OWNERS EXCEPT FOR EMISSION RELATED PARTS. 1-800-432-ECHO.
  • Page 40 PURCHASED REPAIR PARTS, SHORT BLOCKS AND ACCESSORIES ATTENTION TWO-STROKE ENGINE POWER PRODUCT OWNERS (&+2 3RZHU %OHQGŒ 7ZR6WURNH 2LO THIS WARRANTY DOES NOT COVER DAMAGE CAUSED BY: PD[LPXP ® DISCLAIMER OF IMPLIED WARRANTIES MERCHANTABILITY 99922201032 11/18/2011 X7503251406 © 08/2013 ECHO Inc.

  • Page 41: Notes

    CS-370 NOTES NOTES X7503251406 © 08/2013 ECHO Inc.
  • Page 42 NOTES CS-370 X7503251406 © 08/2013 ECHO Inc.
  • Page 43 CS-370 NOTES X7503251406 © 08/2013 ECHO Inc.
  • Page 44 NOTES CS-370 X7503251406 © 08/2013 ECHO Inc.
  • Page 45 CS-370 NOTES X7503251406 © 08/2013 ECHO Inc.
  • Page 46 NOTES CS-370 X7503251406 © 08/2013 ECHO Inc.

  • Page 47: Servicing Information

    Service of this product during the warranty period must be performed by an Authorized ECHO Service Dealer. For the name and address of the Authorized ECHO Service Dealer nearest you, ask your retailer or call: 1-800-432-ECHO (3246). Dealer information is also available on our Web Site. When presenting your unit for Warranty service/repairs, proof of purchase is required.
  • Page 48 C08011001001/C08011999999 ECHO, INCORPORATED C08911001001/C08911999999 C06212001001/C06212999999 400 Oakwood Road Lake Zurich, IL 60047 www.echo-usa.com...

Table of Contents