Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for CDA HVG731MB
Summary of Contents for CDA HVG731MB
- Page 1 HVG631MB HVG731MB Gas hobs Installation, use and maintenance www.cda.co.uk...
-
Page 2: Table Of Contents
Contents: Important information Important safety warnings Using your hob Igniting the hob Using the touch timer Selecting the right burner Care and maintenance Mains electricity connection Installation Ventilation Gas connection Natural gas to LPG conversion Troubleshooting... -
Page 3: Important Information
Appliance information: Please enter the details on the appliance rating plate below for reference, to assist CDA Customer Care in the event of a fault with your appliance and to register your appliance for guarantee purposes. Appliance Model Serial Number... - Page 4 • After use, please ensure that the gas taps are in the ‘Off” position. • Ensure that the appliance is correctly adjusted for the type of gas available before installation. • The use of a gas appliance produces heat and humidity in the room in which it is installed.
- Page 5 8. This appliance is designed for domestic cooking only. Commercial use will invalidate the warranty. 9. Do not cover the hob or place combustible materials on or near the surface even when the hob is not in use. 10. Do not fill deep fat frying containers more than one third full of oil and NEVER leave unattended.
-
Page 6: Using Your Hob
Using your hob Semi-rapid Wok/Triple flame gas burner gas burner 1750W 3500W Semi-rapid Auxiliary gas burner gas burner 1000W 1750W HVG631MB Semi-rapid Rapid gas gas burner burner 3000W 1750W Wok/Triple flame gas burner 3500W Semi-rapid Auxiliary gas burner gas burner... -
Page 7: Igniting The Hob
WARNING! For your own safety, make sure that these instructions on installation, use and maintenance are followed. Igniting the hob burners 1. To light the hob, push down the appropriate knob and turn anti- clockwise to the large flame symbol (Fig.11). 2. -
Page 8: Using The Touch Timer
Using the touch timer 1. Burner timing selection button 2. Timing “-” button 3. Timing “+” button 4. Timing display Note: the timer can be timed normally only when the hob is in working state. 1. Push down the appropriate knob and turn anti-clockwise to light the hob. - Page 9 5. Touching a burner selection button indicator will result in the the corresponding burner flashing and the display showing the remaining time of the burner. (Fig. 16) Fig.16 6. To adjust the time during burner use, touch the corresponding burner button then adjust the time using the “+ or -”...
-
Page 10: Selecting The Right Burner
continue to touch the buttons the hob will directly turn off. If not, the hob will resume as normal. Warning: Do not put anything on the timer touch control area (this may cause incorrect commands or disable the timer). Warning: Power supply failure will cause the program settings to reset. -
Page 11: Care And Maintenance
Care and maintenance When the hob needs to be opened for maintenance, used Circlip pliers remove circlip the Valve body shaft circlip (Fig. 20), then remove the fixing screws on each burner. When installing, first fix the screws of each burner, and then install the lamp circlip assembly on the shaft of the valve body, so that the top surface of the... - Page 12 Stainless steel To clean the hotplate surface, clean with a cloth soaked in hot, soapy water and then dry with a soft cloth to avoid scratching. Plastic To clean the control knobs, wipe clean with a damp, soapy cloth.The control knobs may be removed for thorough cleaning, if necessary, but ensure not to damage the seal.
-
Page 13: Mains Electricity Connection
Mains electricity connection THIS APPLIANCE MUST BE CONNECTED TO THE MAINS SUPPLY BY A COMPETENT PERSON, USING FIXED WIRING VIA A DOUBLE POLE SWITCHED FUSE SPUR OUTLET AND PROTECTED BY A 3A FUSE. We recommend that the appliance is connected by a qualified electrician, who is a member of the N.I.C.E.I.C. - Page 14 L (Live) or coloured red or brown. If the mains cable of this appliance is damaged, it must only be replaced by a CDA approved service engineer, agent, or other suitably qualified person. IMPORTANT – ONLY USE A 3 AMP FUSE The use of a 13A fuse can cause internal wiring damage which will not be covered under the CDA warranty.
-
Page 15: Installation
Installation Warning! 1. Prior to installation, ensure that the local distribution conditions (nature of the gas and gas pressure) and the adjustment of the appliance are compatible 2. The adjustment conditions for this appliance are stated on the label(or data plate) 3. - Page 16 Rear wall should be a flame retardant material Unit: mm 557 477 60min 150min 90min 650min Front edge of worktop Fig. 4 Fig. 5 CAUTION: Accessible parts may be hot when the grill is in use. Young children should be kept away. CAUTION: This appliance is for cooking purposes only.
-
Page 17: Ventilation
Installing and fixing the hob Before inserting the hob into the work surface, please follow the below instructions: 1. Remove the pan stands and burner caps before turning the hob upside down, taking care not to damage the ignition plugs and thermocouples. -
Page 18: Gas Connection
room, BS5440: Part 2 should be consulted to determine air vent requirements. NOTE: The use of a gas cooking appliance results in the production of heat and moisture in the room in which it is installed Always ensure that the kitchen is well ventilated; keep natural ventilation holes open or install a mechanical ventilation device (fig 2). -
Page 19: Natural Gas To Lpg Conversion
The CDA Group Ltd is not legally able to provide any assistance in the installation of gas appliances except to Gas Safe registered installers. Any Gas Safe registered fitter requiring help must provide their name, address and registration number. Information supplied will be validated before help is provided. - Page 20 the minimum position as indicated by the small flame symbol. 2. Remove the control knobs “M” (Fig. 10). 3. Insert a small screwdriver “D” (Fig. 10) into the hole at the top of the tap “C” and turn the adjustment screw left or right until the flame of the burner is conveniently regulated to the low position.
-
Page 21: Troubleshooting
Check that the burner holes are not blocked. no gas Check to see if any gas taps have been left on. If they are off, switch the gas off at the mains and call the CDA customer care team. 4. Smell of gas WARNING! DO NOT check with a naked flame, strike any matches or press ignitor. - Page 22 In the event of your appliance requiring technical assistance and/or spare parts, please contact CDA Customer Care. For more information about the warranty of your product, including terms and conditions, please visit www.cda.co.uk/warranty...
- Page 23 • The energy efficiency of this gas hob was tested and measured according to EN 30-2-1-1998+A1-2003+A2-2005. • The semi-rapid burner and rapid burner were tested separately; the auxiliary burner is not required for test because its nominal heat input is less than 1.16kW. •...
- Page 24 01949 862 012 or email customer.care@cda. co.uk For more information please contact: The Sales Department on 01949 862 010 or email sales@cda.co.uk Customer Care Department. The CDA Group Ltd, Harby Road, Langar, Nottinghamshire, NG13 9HY 01949 862 012 01949 862 003 customer.care@cda.co.uk...
Need help?
Do you have a question about the HVG731MB and is the answer not in the manual?
Questions and answers