Related Manuals for Metso Lokotrack LT220D
Summary of Contents for Metso Lokotrack LT220D
- Page 1 Lokotrack LT-series Doc No. D100018832 Revision 1 Original instructions DRIVING INSTRUCTIONS For more information and language versions, see: metso.com/driving...
- Page 2 Metso's liability for any errors in the document is limited to the documentary correction of errors.
-
Page 3: Table Of Contents
1.4.1 Switching off active regeneration................17 1.4.2 Increasing ground clearance for LT330D/LT220D............ 18 1.5 Stopping the engine........................20 1.6 Troubleshooting........................20 3 (22) © Copyright Metso 2023. All rights reserved. Project ID: Plant Code: Plant Unit Code: Document Type: Running No: Revision:... -
Page 4: Driving Instructions
Read the safety section before working with the unit. Only competent and trained personnel are allowed to work with the unit. 4 (22) © Copyright Metso 2023. All rights reserved. Project ID: Plant Code: Plant Unit Code: Document Type: Running No:... - Page 5 • The lighting is appropriate at the site or near the machine. • The driving surface is not icy or slippery. If needed, sprinkle sand on the surface. 5 (22) © Copyright Metso 2023. All rights reserved. Project ID: Plant Code: Plant Unit Code: Document Type:...
-
Page 6: Starting The Engine
1. Locate the battery isolator switch and make sure that it is in the ON position. See the figure below for possible switch types. Figure 2. Battery isolator switch to ON position 6 (22) © Copyright Metso 2023. All rights reserved. Project ID: Plant Code: Plant Unit Code: Document Type: Running No:... - Page 7 Figure 4. LT300GP/HP (left arrow), LT220D (middle arrow), LT330D, LT130E (right arrow) 2. Check the position of the following switches: 7 (22) © Copyright Metso 2023. All rights reserved. Project ID: Plant Code: Plant Unit Code: Document Type: Running No:...
- Page 8 Figure 6. Control panel key switch ON After initialization, a pop-up with machine information will appear and close automatically after 30 seconds if not closed manually. 8 (22) © Copyright Metso 2023. All rights reserved. Project ID: Plant Code: Plant Unit Code: Document Type: Running No:...
-
Page 9: Handling Alarms
NOTE: Reading and understanding the alarm messages as well as the using the help information will help you to understand functions of the machine. 9 (22) © Copyright Metso 2023. All rights reserved. Project ID: Plant Code: Plant Unit Code: Document Type:... -
Page 10: Driving With Drive Control Device
Driving instructions NOTE: If there is a malfunction that is preventing the track driving, it must be fixed before proceeding. If necessary, contact Metso. In a problem situation, check if there are any active alarms. 1. If the alarm indicator (1) is red and pulsating, tap it. - Page 11 3. Connect the drive control device plug to one of the alternative driving sockets. There are two driving sockets: one at the front (below the control center) and one at the rear of the machine. 11 (22) © Copyright Metso 2023. All rights reserved. Project ID: Plant Code: Plant Unit Code: Document Type:...
- Page 12 Figure 12. Driving socket cover NOTE: Make sure the plug is connected straight and locked with lever (callout (1) in figure above). 12 (22) © Copyright Metso 2023. All rights reserved. Project ID: Plant Code: Plant Unit Code: Document Type: Running No:...
- Page 13 ON (position 1) or the conveyor safety switch (if equipped) is in OFF position (position 0). 13 (22) © Copyright Metso 2023. All rights reserved. Project ID: Plant Code: Plant Unit Code: Document Type: Running No:...
- Page 14 Figure 16. Activating levers in track drive view NOTE: Track driving will deactivate if you stop driving for 2 minutes. Re-activate the levers to continue driving. 14 (22) © Copyright Metso 2023. All rights reserved. Project ID: Plant Code: Plant Unit Code: Document Type: Running No:...
- Page 15 Track drive enabled view. When track driving, the view will show track drive speed with an icon (5) and 1-3 green arrows (6). You can also view engine speed (7). 15 (22) © Copyright Metso 2023. All rights reserved. Project ID: Plant Code: Plant Unit Code: Document Type:...
- Page 16 In bad terrain, the machine might not move if the engine speed is too low. 16 (22) © Copyright Metso 2023. All rights reserved. Project ID: Plant Code: Plant Unit Code: Document Type:...
-
Page 17: Switching Off Active Regeneration
4. If the slider for deactivating active regeneration is grey, tap it so that it turns green (4). 5. To activate regeneration after driving, tap the slider (4) again so that it turns grey. 17 (22) © Copyright Metso 2023. All rights reserved. Project ID: Plant Code: Plant Unit Code: Document Type:... -
Page 18: Increasing Ground Clearance For Lt330D/Lt220D
NOTE: Make sure that there is enough clearance above the conveyors to raise them. Figure 19. LT220D side conveyor valves 2. Connect the plant setup device to the machine (see figures below). 18 (22) © Copyright Metso 2023. All rights reserved. Project ID: Plant Code: Plant Unit Code: Document Type: Running No:... - Page 19 5. Drive the machine to the desired location following these driving instructions. Figure 21. Plant setup device 6. Connect the plant setup device and lower the screen using button (2) in 19 (22) © Copyright Metso 2023. All rights reserved. Project ID: Plant Code: Plant Unit Code: Document Type: Running No:...
-
Page 20: Stopping The Engine
With LT330D/LT220D: There is not enough ground LT220D clearance to drive the machine up or down a steep surface. 20 (22) © Copyright Metso 2023. All rights reserved. Project ID: Plant Code: Plant Unit Code: Document Type: Running No: Revision:... - Page 22 Metso PO Box 1220, FI-00101, Helsinki, Finland Tel +358 20 484 100 www.metso.com © Copyright Metso 2023. All rights reserved.
Need help?
Do you have a question about the Lokotrack LT220D and is the answer not in the manual?
Questions and answers