Download Print this page

Gill WindSonic 1405-PK-040 User Manual

Ultrasonic anemometer

Hide thumbs

Table Of Contents

Table of Contents

Table of Contents
Welcome to the Windsonic User Manual
Overview of Content
Description of Icons
General Notes
User Manual Revision History
Product Overview
Pre-Installation
Equipment Supplied
Windsonic Accessories
Windsonic CE, UKCA, FCC Conformity
Right to Change and Revise
Packaging
Windsonic Specification
Downloadable Software
Windsonic Part Numbers
Requirements & Installation
Installation Requirements
Installation Guidelines
Bench System Test
Electrical
Connecting to a PC Using RS-232 (Option 1 Sensor) Power and Communications Cable
Connecting Windsonic Option 2 or 3 Set for Default RS-422 Using Safe Mode
Changing an Option 2 or 3 Sensor Set for RS-232 Back to RS-422
Connecting to a PC Using RS-422 (Option 2 or 3)
Using RS-485 (2 Wire Point to Point ) with Option 2 or 3 Units
Using the Analogue Output (Option 3)
Mechanical
Orientation
Alignment
Mounting
Message Formats
Gill Format- Polar, (Default Format)
Gill Format - UV
NMEA Format (NMEA Status Codes)
NMEA Format (Gill Status Codes)
Gill Format - Tunnel Mode (UU, Continuous )
Gill Format - UV with Gust
Gill Format - Polar with Gust
Analogue Outputs and Options
Wind Speed Scaling
Tunnel Mode
Error Condition Reporting
Analogue Output Rate
Disabled Outputs
Analogue Output Conditions
Cable Type
Cable Length
Connecting to an SDI-12 Interface (Option 4)
Appendix A - Technical Specification (Options 1, 2 & 3)
Windsonic Option 4 Specification
Appendix B - Cable Assembly
Soldering Contacts
Connector Assembly
Connector Spares
Appendix C - Windsonic Default Setup
Appendix D - Windsonic Safe Mode
Using Safe Mode to Get Communication and to Change Settings
Operation Method Summary
Appendix E - Configuring
Configuring Using Terminal Package
Entering Configuration Mode
Returning to Measurement Mode
Checking the Configuration
Changing a Setting
Appendix F - SDI-12 Commands
Gill Output Message Format
Commands and Returns in Low Power Mode (Axlpm!)
Appendix G - Configuration Commands
Bx - Baud Rate
CX - Analogue Settings
DX - Diagnostic and Configuration Command
Ex - Communications Protocol
Fx - Data and Parity Options
Gx - Reserved for Gill Use Only
Gustintx - Gust Interval in Minutes
Hx - Power-Up Message
Kxx to Kxxxx - Minimum Direction Velocity
Lx - Message Terminator
MX to MXX - Message Format
Nx - Node Address
Ox - ASCII Output Format
Px to Pxx - Output Rate
Q - Measurement Mode
Tx - Analogue Output Type (Voltage or Current)
Ux - Output Units
Yx - Analogue Output, Error Status Condition
Sx - Analogue Output Range
Configuration / Diagnostic Information
Appendix H - Polled Mode Commands
Gill Format - Polled (Polar or UV)
Appendix I - Wind View Software
Appendix J - Status Codes
Option 1-3 Status Codes
SDI-12 Status Codes
Appendix K - Maintenance & Fault-Finding
Cleaning
Servicing
Fault Finding
Returning Unit
Bench Test
Self - Test (Still Air)
Calibration
Appendix L - Glossary & Abbreviations

Quick Links

Download this manual

Wind speed & direction sensor

xxx

Ultrasonic Anemometer

User Manual

Applies to WindSonic option 1-3 units

with firmware 2368-113-04 onwards

Applies to WindSonic 75 option 1 and 2 units

with firmware 2368-107-01

Applies to WindSonic 75 option 3 units

with firmware 2816-100

Applies to option 4 SDI-12 units from June 2011

with serial numbers 1122007 onwards.

gillinstruments.com

Doc No: 1405-PS-0019

Issue 31

Manual

Table of Contents

Need help?

Do you have a question about the WindSonic 1405-PK-040 and is the answer not in the manual?

Gill WindSonic 1405-PK-040 User Manual

Quick Links

Need help?

Questions and answers

Related Manuals for Gill WindSonic 1405-PK-040

Table of Contents