Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Kramer GP2-890R 2021
Summarization of Contents
Introduction
About This Manual
Guide for proper procedures for motorcycle basic operation, inspection, and maintenance.
Usage and Setup
Identification / Serial Numbers
Locate motorcycle serial numbers for chassis, engine, forks, and shock.
Operating Components
Identify key components like fuel fill and oil level check points.
Control Components
Overview of hand and foot controls, switches, levers, and pedals.
Start Up Procedure
Step-by-step guide for safely starting the motorcycle engine.
Shut Down Procedure
Step-by-step guide for safely shutting down the motorcycle engine.
Vehicle Break-in Procedure
Guidelines and limits for breaking in the motorcycle during initial use.
Pre-Ride Inspection
Essential checks before riding for safety and readiness.
Post-Race Service
Maintenance procedures required after each race or track day.
Post-Crash Inspection
Procedures for inspecting the motorcycle after an accident.
Transporting / Loading
Recommended tie-down points and methods for motorcycle transport.
Raising the Motorcycle on Lift Stands
Instructions for safely lifting the motorcycle using stands.
Storage
Steps for preparing and storing the motorcycle for extended periods.
Removing from Storage
Procedures for taking the motorcycle out of storage.
Maintenance / Service
Service Schedule
Detailed list of scheduled maintenance tasks and intervals.
Checking the Engine Oil Level
Procedure for checking the engine oil level correctly.
Changing the Engine Oil & Filter, and Cleaning the Oil Screens
Detailed steps for oil change and cleaning oil screens.
Chain Cleaning / Lubrication
Procedure for cleaning and lubricating the motorcycle chain.
Checking the Chain Tension
How to check and measure the correct chain tension.
Adjusting the Chain Tension / Rear Axle Alignment
Steps to adjust chain tension and align the rear axle.
Fuel Filler Cap
Instructions for opening and closing the fuel filler cap.
Air Filter Servicing
Steps for removing, cleaning, and installing the air filter.
Engine
Repairs
Advice on contacting a dealer for engine damage or problems.
Repack the Muffler
Information on when and how to repack the muffler.
Motorcycle Controls Overview
Explains throttle response, engine braking, and pit limiter functions.
Cooling System
Checking the Coolant Level
Procedure for checking the coolant level in the radiator.
Draining the Coolant
Steps to drain the coolant from the system.
Filling/Bleeding the Cooling System
Instructions for filling and bleeding air from the cooling system.
Chassis
Handlebar Adjustment
How to adjust handlebar height, angle, and width.
Steering Damper Setup
Adjusting the firmness of the steering damper.
Seat/Tank Height Adjustment
Adjusting seat and tank height using eccentric mounts.
Bodywork Removal
Step-by-step guide to removing various bodywork pieces.
Bodywork Installation
Steps for reinstalling bodywork pieces in reverse order.
Fuel Tank Draining Procedure
Safe procedure for draining fuel from the tank.
Fuel Tank Removal/Installation
Detailed steps for removing and installing the fuel tank.
Clutch Lever Free Play and Reach Distance
How to check and adjust clutch lever free play and reach.
Front Brake Lever Response and Travel Distance
Adjusting front brake response, ratio, and lever reach.
Rearset Setup
Adjusting foot pegs, shift lever, and brake lever for personalized setting.
Rear Brake Lever Adjustment
How to adjust the rear brake lever position.
Shift Lever Height Adjustment
Adjusting the shift lever height by changing linkage length.
Brake System
Brake Inspection
Inspecting brake pads and discs for wear and damage.
Brake Fluid Level
Checking and adding front and rear brake fluid.
Brake Bleeding
Procedures for bleeding front and rear brake calipers.
Changing the Brake Pads
Step-by-step guide to changing front and rear brake pads.
Suspension
Suspension Inspection
Inspecting front forks, rear suspension, and swingarm for issues.
Checking the Steering Head Bearing Play
How to check for play in the steering head bearings.
Adjusting the Steering Head Bearing Play
Steps to adjust steering head bearing play and check smoothness.
Changing the Fork Offset
Procedure for changing the fork offset to alter steering geometry.
Fork Suspension Settings
Adjusting fork spring preload, compression, and rebound damping.
Fork Specifications
Technical data for the front fork, including spring rates and length.
Rear Shock Suspension Settings
Adjusting rear shock preload, compression, and rebound damping.
Shock Absorber Specifications
Technical data for the rear shock absorber.
Wheels
Front Wheel Removal
Step-by-step guide to removing the front wheel.
Front Wheel Installation
Step-by-step guide to installing the front wheel.
Rear Wheel Removal
Step-by-step guide to removing the rear wheel.
Rear Wheel Installation
Step-by-step guide to installing the rear wheel.
Electrical
Tail light Operation
How to switch the tail light on/off and change modes.
Charging the Tail light
Instructions for removing and charging the tail light.
Fuses
Location and identification of fuses and how to change them.
Battery
Location, charging, removal, and installation of the battery.
Powered Accessory Leads
Information on the 12-volt powered accessory leads.
Technical Data
GP2 890-R Specifications
General specifications for the motorcycle model.
Engine Specifications
Detailed technical data for the engine.
Fluid Capacities
Capacities for engine oil, coolant, brake fluid, and fuel.
Electrical System
Technical data for the electrical system components.
Torque Specifications
Engine Torque Chart
A chart listing torque specifications for engine components.
Chassis Torque Chart
A chart listing torque specifications for chassis components.
Safety Wire
Explanation and steps for installing safety wire on fasteners.
Dashboard
AIM Compact MXS 1.2 Dash Logger
Introduction to the dash logger and its capabilities.
Dash Logger Indicators Overview
Explains the various indicators and their meanings on the dash logger.
Dash Logger Menu Configuration Settings
How to navigate the dash logger's configuration menus.
Set Date and Time
Instructions for setting the date and time on the dash logger.
Set Backlight
How to adjust the display brightness and LED settings.
Set Video Input
Configuration options for video input on the dash logger.
Lap Time Setup
Setting up predictive reference for lap times.
Counters Management
Managing user and system odometers.
GPS & Tracks
How the dash logger uses GPS for track data and lap timing.
Wi-Fi Management
Settings for Wi-Fi connectivity, modes, and channel selection.
System Info
Displays system information like model name, serial number, and firmware.
GPS Search
Checking the connection status of GPS satellites.
Sampled Data Recall
Recalling and viewing sampled test session data.
Pit Limiter Indicator
Explains the display when the motorcycle is in Pit Limiter mode.
Need help?
Do you have a question about the GP2-890R 2021 and is the answer not in the manual?
Questions and answers