Sony HCD-HPR90 - Receiver Component For Mini Hi-fi Systems Service Manual page 6

HCD-HPR90/HPR99XM
– HPR99XM –
Basic Operations
Adjusting the sound
To adjust the volume
Press VOLUME +/– on the remote (or turn the
VOLUME control on the unit)
To add a sound effect
To
Generate a more dynamic
sound (Dynamic Sound
Generator X-tra)
Set the sound effect
Playing a CD/ATRAC/MP3 disc
1
Select the CD function.
Press CD
2
Place a disc.
Press
disc with the label side up on the disc tray.
To insert additional discs, slide the disc tray with your
finger as shown below.
To close the disc tray, press
the unit again.
Do not force the disc tray closed with your finger, as
this may damage the unit.
3
Start playback.
Press
pause)
Before using the system
To
Pause playback
To use the remote
Slide and remove the battery compartment lid wd , and
insert the two supplied R6 (size AA) batteries, side
first, matching the polarities shown below.
Stop playback
Select a folder on
an "ATRAC" disc or
MP3 disc
Notes on using the remote
Select a track or file
• With normal use, the batteries should last for about six months.
• Do not mix an old battery with a new one or mix different types of
batteries.
• If you do not use the remote for a long period of time, remove the
batteries to avoid damage from battery leakage and corrosion.
To receive the XM Satellite Radio Find a point in a
track or file
Introducing XM Satellite Radio
XM Radio is the satellite radio service with millions of listeners
across the U.S. Broadcasting live daily. XM Radio offers 160
digital radio channels offering music, news, sports, comedy, talk,
Select Repeat Play
entertainment, traffic and weather reports, with high quality digital
sound.
Select a disc
How to Subscribe
XM $12.95 monthly service subscription sold separately. XM
Connect and Play (TM) antenna required to receive XM service (sold
separately). Installation costs and other fees and taxes, including a
Switch to CD
one-time activation fee may apply. Subscription fee is consumer only.
All fees and programming subject to change. Channels with frequent
function from
explicit language are indicated with an XL. Channel blocking is
another source
available for XM radio receivers by calling 1-800-XMRADIO.
Exchange other
Subscriptions subject to Customer Agreement available
at xmradio.com. XM service only available in the 48 contiguous
discs while playing
United States. XM Ready and XM Connect-and-Play are trademarks
of XM Satellite Radio Inc. (C)2005 XM Satellite Radio Inc. All rights
To change the play mode
reserved.
Press PLAY MODE
Activate XM Service
stopped. You can select normal play ("ALL DISCS" for
Find the 8-character XM Radio ID of the Connect-and-Play antenna.
all discs, "1DISC" for a disc, or "
With the Connect-and-Play antenna connected to the unit, the Radio
ID can be found by selecting channel 0 on the radio. Press >10, 10/0,
files and MP3 files in the folder on the disc), shuffle
10/0, 10/0 on the remote in that order to select channel 0.
play ("ALL DISCS SHUF," "1DISC SHUF," or "
Record the Radio ID here for reference: _______________________.
SHUF*"), or program play ("PGM").
(NOTE: The XM Radio ID does not use the letters I, O, S, or F.)
* When playing a CD-DA disc,
Activate your XM Satellite Radio service online
operation as 1DISC (SHUF) Play.
at http://activate.xmradio.com or by calling 1-800-XMRADIO
(1-800-967-2346). You will need a major credit card.
To select a CD track using the number
XM will send a signal from the satellites to activate the full channel
lineup. Activation normally takes 10 to 15 minutes, but during peak buttons
busy periods, you may need to keep your player on for up to an hour.
Press the number buttons
When you can access the full channel lineup on your player, you're
normal play. For example, to enter 20, press >10, 2, 10/0,
done.
in that order.
Notes on XM Satellite Radio
• To ensure optimal reception of XM's satellite signal, move your To create an "ATRAC"/MP3 disc
antenna to various window locations around your home to see
You can create an "ATRAC" disc and MP3 disc with the
where the best reception will be received. Most XM customers
SonicStage software. SonicStage can be
place the antenna in a south-facing window with a clear view to the
downloaded free of charge from the following sites and
sky.
• Residents in Canada please see information about XM Canada at installed on your computer.
the following webpage: (http://www.xmradio.ca/)
For customers in the U.S.A.:
<http://www.sony.com/shelfsupport>
To set the clock
For customers in Canada:
1
Turn on the system.
<http://www.sony.ca/ElectronicsSupport/>
Press (power) . Please see the instructions at the sites or SonicStage Help
of the software for how to install and how to create an
2
Select the clock set mode.
"ATRAC"/MP3 disc.
Press CLOCK/TIMER SET ws on the remote. If the
Note on the jog dial
current mode appears on the display, press /
Only the first 6 characters are displayed when performing the folder
on the remote repeatedly to select "CLOCK SET"
search, track search, or file search.
and then press ENTER 8 on the remote.
Notes on Repeat Play
3
Set the time.
• All tracks or files on a disc are played repeatedly up to five times.
Press / on the remote repeatedly to set • You cannot select "REP" and "ALL DISCS SHUF" at the same
time.
the hour, and then press ENTER on the remote.
8
• "REP 1" indicates that a single track or file is repeated until you
Use the same procedure to set the minute.
stop it.
When you turn off the system after setting the clock,
Notes on playing MP3 discs
the clock display appears instead of the demonstration
• Do not save other types of files or unnecessary folders on a disc that
display.
has "ATRAC" and MP3 files.
The clock settings are lost when you disconnect the
• Folders that have no "ATRAC" and MP3 files are skipped.
power cord or if a power failure occurs. • "ATRAC" and MP3 files are played back in the order that they are
recorded onto the disc.
• The system can only play MP3 files that have a file extension of
Selecting a music source ".MP3."
• If there are files on the disc that have the ".MP3" file extension,
but that are not MP3 files, the unit may produce noise or may
Press the following buttons (or press FUNCTION on
malfunction.
the remote repeatedly).
• The maximum number of:
– "ATRAC" folders is 255.
To select Press
– "ATRAC" files is 999.
CD CD on the remote.
– MP3 folders is 255 (including the root folder).
– MP3 files is 511.
Tuner TUNER/BAND .
– MP3 files and folders that can be contained on a single disc is 512.
Component (connected AUDIO IN . – folder levels (the tree structure of files) is 8.
qk
using an audio cord)
6
• Compatibility with all MP3 encoding/writing software, recording
device, and recording media cannot be guaranteed. Incompatible
MP3 discs may produce noise or interrupted audio or may not play
at all.
• If "ATRAC" files and MP3 files are recorded on the same disc, this
system plays the "ATRAC" files first.
Notes on playing multisession discs
.
• If the disc begins with a CD-DA (or "ATRAC"/MP3) session, it is
recognized as a CD-DA (or "ATRAC"/MP3) disc, and other sessions
are not played back.
• A disc with a mixed CD format is recognized as a CD-DA (audio)
Press
disc.
DSGX on the unit.
Listening to the radio
EQ on the remote
ql
repeatedly to select "BASS"
To listen to FM or AM
or "TREBLE," and then
press +/– on the remote
1
Select "FM" or "AM."
repeatedly to adjust the level.
Press TUNER/BAND
2
Select the tuning mode.
Press TUNING MODE
appears.
3
Tune in the desired station.
Press +/– on the remote (or TUNING +/– on the unit)
on the remote.
. Scanning stops automatically when a station is
tuned in, and then "TUNED" and "STEREO" (for
stereo programs) appear.
(CD open/close) on the unit, and place a
To stop automatic scanning
Press (stop)
To tune in a station with a weak signal
If "TUNED" does not appear and the scanning does
not stop, press TUNING MODE
"AUTO" and "PRESET" disappear, and then press
+/– on the remote (or TUNING +/– on the unit)
repeatedly to tune in the desired station.
To reduce static noise on a weak FM stereo
station
Press FM MODE
to turn off stereo reception.
To listen to XM
You can operate and listen to the XM satellite Radio by
(CD open/close) on
connecting your XM Connect-and-Play antenna. Before
using the system, connect the XM Connect-and-Play
antenna to the XM jack of the system (see "Hooking up
the system securely").
1
Select "XM."
(play) wa on the remote (or CD/ (play/
Press XM on the remote (or TUNER/BAND
on the unit).
repeatedly) qk
2
Select the All Channel mode.
Press
Press TUNING MODE
(pause) wa on the remote (or
and "PRESET" disappear.
CD/ (play/pause) on the
unit). To resume play, press the 3
Tune in the desired channel.
button again.
Press +/– on the remote (or TUNING+/– on the unit)
6
(stop) . repeatedly.
+/– (select folder) . Or
To select a channel by Category mode
turn the jog dial on the unit
1
Press XM on the remote (or TUNER/BAND
and press PUSH ENTER on
repeatedly)
qk
the unit (turn the jog dial on
2
the unit during playback until Press TUNING MODE
"GROUP" appears, and then appears.
press PUSH ENTER on the
3
Press CATEGORY +/– on the remote (or CAT
unit to select the desired folder).
+/– on the unit)
/ (go back/go forward) 4
Press +/– on the remote (or TUNING +/– on the
. Or turn the jog dial on
unit) repeatedly.
6
the unit and press PUSH ENTER
on the unit. To cancel, press To select a channel using the number
buttons
CANCEL on the unit.
Press the number buttons
Hold down / (rewind/fast
to enter 20, press >10, 10/0, 2, 10/0, in that order. You
forward) during playback,
cannot enter 255 or more.
and release the button at the
desired point.
Notes
• If you select a channel that is not broadcasted, "OFF AIR" appears
REPEAT repeatedly until
and the previous channel is selected.
"REP" or "REP1" appears.
• If you select a channel using the number buttons in Category mode,
the tuning mode changes to All Channel mode automatically.
DISC SKIP on the remote (or
DISC 1 – 5 or DISC SKIP
(in stop mode) on the unit).
Changing the display
DISC 1 – 5 on the unit
(Automatic Source Selection).
To change
EX-CHANGE on the unit.
Information on
the display*
Display mode
(See below.)
repeatedly while the player is
* For example, you can view CD/"ATRAC"/MP3 disc information,
such as the track or file number or folder name during normal play,
*" for all "ATRAC"
or the total play time while the player is stopped. You can also view
XM radio information, such as the channel name, song title and
artist name.
The system offers the following display modes.
(SHUF) Play performs the same
Display mode
Demonstration
on the remote during
Clock
Power Saving
2)
Mode
1) The STANDBY indicator lights up when the system is off.
2)
When the system is in Power Saving Mode, the following functions
are unavailable:
– setting the clock
– changing the AM tuning interval
– changing the CD power manage function
Notes on the display information
• The following are not displayed;
– total playing time for a CD-DA disc depending on the play mode.
– total playing time for an "ATRAC"/MP3 disc.
– remaining playing time for an MP3 file.
• The following are not displayed correctly;
– elapsed playing time of an "ATRAC" file or MP3 file encoded
using a VBR (variable bit rate).
– folder and file names that do not follow either the ISO9660 Level
1, Level 2 or Joliet in the expansion format.
• The following are displayed;
– ID3 tag information for "ATRAC" files and MP3 files when ID3
version 1 and version 2 tags are used.
– up to 62 characters of ID3 tag information using uppercase letters
(A to Z), numbers (0 to 9), and symbols (" $ % ' ( ) * + , – . / < =
> @ [ \ ] _ ` { | } ! ? ^).
Using optional audio
components
To connect an optional headphones
Connect headphones to the PHONES jack
unit.
To connect an optional component
Connect additional audio component to the AUDIO
IN jack on the unit using an audio analog cord (not
supplied). Turn down the volume on the system, and then
press FUNCTION
the AUDIO IN function.
Other Operations
Creating your own CD program
(Program Play)
Use buttons on the remote to create your own program.
1
Press CD to select the CD function.
2
Press PLAY MODE
appears while the player is stopped.
3
Press DISC SKIP
4
Press /
dial on the unit until the desired track number
appears.
When programming "ATRAC" files or MP3 files,
press +/– (select folder)
jog dial on the unit to select the desired folder, and
then select the desired file.
repeatedly.
Current disc
Selected track
repeatedly until "AUTO"
or file number
Loaded disc
5
Press ENTER
8
program.
"– –.– –" appears when the total time exceeds 100
minutes for a CD, or when you select a CD track
whose number is 21 or over, or when you select an
"ATRAC" file or MP3 file.
.
6
Repeat steps 4 through 5 to program additional
tracks or files, up to a total of 25 tracks or files.
7
To play your program of tracks or files, press
repeatedly until
(play) .
wa
The program remains available until you open the disc
tray. To play the same program again, select the CD
function, and press
To cancel Program Play
repeatedly until "MONO" appears Press PLAY MODE
disappears while the player is stopped.
To delete the last track or file of the program
Press CLEAR w; while the player is stopped.
To view program information, such as total
track number of the program
Press DISPLAY repeatedly.
Tip
You can program additional tracks or files during playback by using
the jog dial.
.
qa repeatedly until "CAT" Presetting radio stations
You can preset your favorite radio stations and tune
them in instantly by selecting the corresponding preset
number.
Use buttons on the remote to preset stations.
1
Tune in the desired station (see "Listening to the
radio").
. 2
Press TUNER MEMORY
repeatedly until "CAT"
qa
repeatedly.
6
3
Press +/– repeatedly to select your desired
preset number.
wh on the remote. For example,
If another station is already assigned to the selected
preset number, the station is replaced by the new
stations.
4
Press ENTER
8
5
Repeat steps 1 through 4 to store other stations.
You can preset up to 20 FM, 10 AM and 20 XM
stations. The preset stations are retained for about half
a day even if you disconnect the power cord or if a
power failure occurs.
6
To call up a preset radio station, press TUNING
MODE repeatedly until "PRESET" appears,
and then press +/–
Press
desired preset number.
DISPLAY repeatedly when the
system is on. Note on presetting XM stations
You cannot preset XM stations except when you receive the station.
DISPLAY repeatedly when the
system is off.
Using the Timers
The system offers two timer functions. If you use Play
Timer with the Sleep Timer, the Sleep Timer has priority.
Sleep Timer:
You can fall asleep to music. This function works even if
When the system is off, 1)
the clock is not set.
The clock display is replaced by
Press SLEEP wf on the remote repeatedly. If you select
lighting and flashing of the display
"AUTO," the system automatically turns off after the
window.
current disc stops or in 100 minutes.
The clock is displayed.
Play Timer:
The display is turned off to conserve
You can wake up to CD or tuner at a preset time.
power. The timer and clock continue
to operate.
Use buttons on the remote to control the Play Timer.
Make sure you have set the clock.
1
Prepare the sound source.
Prepare the sound source, and then press VOLUME
+/– to adjust the volume.
To start from a specific CD track, "ATRAC" file or
MP3 file, create your own CD program.
2
Press CLOCK/TIMER SET
3
Press /
SET" then press ENTER
"ON" appears, and the hour indication flashes.
4
Set the time to start playing.
Press /
and then press ENTER
The minute indication flashes. Use the procedure
above to set the minute.
5
Use the same procedure as in step 4 to set the
time to stop playing.
6
Select the sound source.
Press /
sound source appears, and then press ENTER
display shows the timer settings.
7
Press (power)
The system turns on 15 seconds before the preset
time. If the system is on at the preset time, the Play
on the
Timer will not play.
on the remote repeatedly to select
To activate or check the timer again
Press CLOCK/TIMER SELECT
repeatedly until "PLAY SEL" appears, and then press
ENTER 8 .
To cancel the timer
Repeat the same procedure as above until "TIMER OFF"
repeatedly until "PGM"
appears, and then press ENTER
To change the setting
to select a disc.
Start over from step 1.
repeatedly or turn the jog
Tip
The Play Timer setting remains as long as the setting is not canceled
manually.
repeatedly or turn the
Total playing time of program
(including selected track or file)
to add the track or file to the
(play) wa .
repeatedly until "PGM"
wg .
Preset number
.
repeatedly to select the
ws .
repeatedly to select "PLAY
8 .
repeatedly to set the hour,
.
8
repeatedly until the desired
8 . The
to turn off the system.
ws , press /
8 .