General; Maintenance; Cleaning The Tv Cabinet; Cleaning The Tv Screen - Dynex DX-15L150A11 User Manual

Maintenance

General

Problem
One or more channels do
not display.
Password is lost.
Some settings cannot be
accessed.
TV cabinet creaks.
Control buttons on the TV
do not work.
Note: If the problem is not solved by using these troubleshooting
instructions, try turning off your TV, then turning it on again.
Maintenance
• Do not use your TV in areas that are too hot or too cold, because
the cabinet may warp or the screen may malfunction. Your TV
works best in temperatures that are comfortable to you.
• Storage temperatures are 32° to 122°F (0° to 50°C).
• Working temperatures are 41° to 104°F (5° to 40°C).
• Do not place your TV in direct sunlight or near a heat source.

Cleaning the TV cabinet

Clean the cabinet with a soft, lint-free cloth. If the cabinet is especially
dirty, moisten a soft, lint-free cloth in a weak detergent solution,
squeeze the excess moisture from the cloth, then wipe the screen or
cabinet with the cloth. Use a clean cloth to dry the screen or cabinet.

Cleaning the TV screen

Clean the screen with a soft, lint-free cloth.
Solution
• Make sure that the channels are
not blocked. For more
information, see "Setting parental
control levels" on page 21.
• Make sure that the channels are
not hidden. For more information,
see "Hiding and adding channels"
on page 18.
• The channel may have been
deleted from the channel list. You
can tune to the channel by
pressing the number buttons or
you can add the channel back to
the channel list. For more
information, see "Changing
channel settings" on page 18.
• Enter 9999 to access the parental
controls, then set a new
password. For more information,
see "Setting parental controls" on
page 20.
• If a setting is grayed, the setting is
not available in the current video
input mode.
• When the TV is in use, the
temperature rises naturally and
may cause the cabinet to expand
or contract which can cause a
creaking noise. This is not a
malfunction.
• Disconnect the power cord, wait a
few seconds, then reconnect the
power cord and turn on the TV.
• Make sure that the Button Lock
option is set to Off. For more
information, see "Locking control
buttons" on page 23.
DX-15L150A11/DX19L150A11/DX-22L150A11

Specifications

Specifications subject to change without notice.
Weight and dimensions shown are approximate.
NTSC
Analog standard
ATSC, 8-VSB, Clear-QAM
Digital standard
DX-15L150A11 - 15"
Screen
DX-19L150A11 - 19"
DX-22L150A11 - 22"
VHF: 2 - 13
Channel coverage
UHF: 14 - 69
CATV: Mid band - A8~A-1,A~I
Super band - J~W
Hyper band - AA~ZZ, AAA, BBB
Ultra band: 65~94, 100~135
AC 120 V ~ 60 Hz
Power source
15" - 42 W with TV on
Power consumption
19" - 45 W with TV on
22" - 62 W with TV on
<1 W in standby mode
3 W + 3 W internal speaker
Audio power
Y: 1 V (p-p), 75 ohm, negative sync
S-Video input
C: 0.286 V (p-p) (burst signal), 75 ohm
Video: 1 V (p-p), 75 ohm, negative sync
Video/audio input
Audio 500mV (rms)
Y: 1 V (p-p), 75 ohm, including sync
Component input
PR/CR: ±0.35 V (p-p), 75 ohm
PB/CB: ±0.35 V (p-p), 75 ohm
Audio: 500 mV (rms)
Suggested resolutions: 1080i, 720p,
480p, 480i
1 HDMI input jack
HDMI input
HDCP compliant
E-EDID compliant
Suggested scan rates: 1080p,1080i,
720p, 480p, 480i
E-EDID compliant
VGA input
Suggested scan rates: 640x480/60 Hz,
800x600/60 Hz, 1024x768/60 Hz,
1360x768/60 Hz
Audio input: Mini-jack for stereo

Legal notices

FCC Part 15
This device complies with Part 15 of the FCC Rules. Operation of this
product is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply within the limits
for a class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
29