Table of Contents
Advertisement
Quick Links
WHY READ THIS MANUAL?
Before operating your new Brush Wolf brush cutter, read this entire manual to understand
1) safety precautions, 2) operating instructions, and 3) maintenance schedule to help keep
you safe and your equipment running smoothly for years to come.
Operator's Manual
SKID STEER BRUSH CUT TERS
Open Front/Heavy-Duty Series
6601 LF
7201 LF
|
6601 SF
| 7201 HF
|
7201 SF
|
7201 HF
7801 SF
|
7801 HF
Advertisement
Table of Contents
Related Manuals for Brush Wolf 7201 LF
Summary of Contents for Brush Wolf 7201 LF
- Page 1 7801 HF WHY READ THIS MANUAL? Before operating your new Brush Wolf brush cutter, read this entire manual to understand 1) safety precautions, 2) operating instructions, and 3) maintenance schedule to help keep you safe and your equipment running smoothly for years to come.
- Page 2 TAKE A MINUTE TO WRITE DOWN THE FOLLOWING INFORMATION FOR FUTURE SERVICE, REPAIR, AND WARRANTY INQUIRIES. OWNER REFERENCE INFORMATION DATE OF PURCHASE ____________________________________________________ MODEL NO. ____________________________________________________ SERIAL NO. ____________________________________________________ DEALER NAME ____________________________________________________ SALES REP NAME ____________________________________________________ DEALER PHONE NO. ____________________________________________________ DEALER EMAIL ____________________________________________________ DEALER ADDRESS ____________________________________________________ ____________________________________________________...
-
Page 3: Table Of Contents
THANK YOU Welcome to the Brush Wolf family! You’ve made a smart choice! We hope you love your brush cutter as much as we love making it. If you have any issues, please contact us at any time. We’re here to help. -
Page 4: Safety First
Brush Wolf/Cross-Tech Manufacturing cannot cover every incident that might be a hazard. Extreme caution should be used at all times. Only use your Brush Wolf brush cutter for the purpose for which it has been designed. SITE INSPECTION ... - Page 5 BRUSH WOLF OPERATOR’S MANUAL | SAFETY FIRST! DO NOT DO NOT operate near bystanders, vehicles, raise the mower deck while blades pets, livestock, or buildings. Objects may are rotating. Operation with the mower raised discharge while cutting with the brush cutter will expose the cutting blades and may cause and has the potential to cause serious injury.
-
Page 6: Operating Your Brush Cutter
OPERATING YOUR BRUSH CUTTER FIGURE 1: SERIAL TAG START HERE Verify your skid steer’s hydraulic fl ow to ensure it is within the brush cutter’s rating range. The brush cutter’s gallons per minute (GPM) rating is located on the serial tag of the brush cutter. - Page 7 BRUSH WOLF OPERATOR’S MANUAL | OPERATING YOUR BRUSH CUTTER CONNECTING THE BRUSH CUTTER 1) Connect the brush cutter to your skid steer 3) Inspect the hydraulic couplers and wipe off with the universal Quick Tach Mount Plate. water, dust, or any debris which can damage hydraulic components.
- Page 8 BRUSH WOLF OPERATOR’S MANUAL | OPERATING YOUR BRUSH CUTTER FIGURE 3: BLADE ROTATION OPERATING STEPS COUNTERCLOCKWISE 1) Enter the shatter-proof cab door, engage the seat belt, release the brake, and start the engine. The runners of the brush cutter should be as close to the ground as possible.
-
Page 9: Maintenance
MAINTENANCE BRUSH WOLF BRUSH CUTTERS ARE BUILT TO STRICT STANDARDS AND WILL DELIVER YEARS OF DEPENDABLE SERVICE WHEN YOU FOLLOW THESE MAINTENANCE GUIDELINES... MAINTENANCE SCHEDULE See pages 8-9 for details. BEFORE DAILY OR ITEM EACH USE EVERY 8 HOURS... - Page 10 BRUSH WOLF OPERATOR’S MANUAL | MAINTENANCE BEFORE EVERY OPERATION INSPECT BLADES CHECK THE GEARBOX FOR PROPER LUBRICANT Inspect blades before each use to ensure To check the lubricant level, remove the they are sharp, tightened correctly, and pipe plug from the side of the gearbox.
- Page 11 Also, tighten the castle nut holding the blade CHECK NUTS & BOLTS carrier to the output shaft of the gearbox, Every Brush Wolf brush cutter is tested at torque to 450 ft-lbs with a 1-1/2” socket the factory and all nuts and bolts have been wrench.
-
Page 12: Troubleshooting
TROUBLESHOOTING CONSULT YOUR DEALER OR CONTACT BRUSH WOLF FOR ANY QUESTIONS OR ADDITIONAL HELP. ISSUE POTENTIAL CAUSES • Low hydraulic fluid level • Overheated hydraulic fluid* • Contaminated hydraulic fluid* Loss of Power • Low gearbox lubricant level • Broken gearbox/motor shear pin •... -
Page 13: How To Replace Blades
HOW TO REPLACE BLADES Perform replacement on a level surface with the brush cutter blocked off the ground. Shut off the hydraulic power supply and disconnect hydraulic couplers. 1) Take off the access cover (see Figure 5 on 5) Use Primer Loctite on the bolts and nuts page 9) by removing the nuts and washers. -
Page 14: 6601 Lf | 6601 Sf
PARTS: 6601 LF 6601 SF DETAIL A 877-390-9857 | brushwolf.com... - Page 15 ONLY USE GENUINE OEM PARTS. ORDER PARTS FROM BRUSH WOLF AT 877-390-9857 ITEM PART ITEM DESCRIPTION NUMBER 15054 PLATE, ACCESS, 2 HOLE, 5.250 X 3.250 X 0.250 15057 WELDMENT, BLADE CARRIER, 25.000 DIA X .313, SPUN FORMED PAN 15066 BOLT, D-BOLT, 1 1/8-12, BW...
-
Page 16: 7201 Lf | 7201 Sf
PARTS: 7201 LF 7201 SF DETAIL A 877-390-9857 | brushwolf.com... - Page 17 ONLY USE GENUINE OEM PARTS. ORDER PARTS FROM BRUSH WOLF AT 877-390-9857 ITEM PART ITEM DESCRIPTION NUMBER 15054 PLATE, ACCESS, 2 HOLE, 5.250 X 3.250 X 0.250 15067 GUARD, COUPLING, BW, STD 15317 WELDMENT, FRAME, BW 7201 15057 WELDMENT, BLADE CARRIER, 25.000 DIA X .313, SPUN FORMED PAN...
-
Page 18: 7201 Hf
PARTS: 7201 HF 31 4X 39 8X DETAIL A 877-390-9857 | brushwolf.com... - Page 19 ONLY USE GENUINE OEM PARTS. ORDER PARTS FROM BRUSH WOLF AT 877-390-9857 ITEM PART ITEM DESCRIPTION NUMBER 15054 PLATE, ACCESS, 2 HOLE, 5.250 X 3.250 X 0.250 15067 GUARD, COUPLING, BW, STD 15057 WELDMENT, BLADE CARRIER, 25.000 DIA X .313, SPUN FORMED PAN...
-
Page 20: 7801 Sf
PARTS: 7801 SF 26 2X 28 2X DETAIL A 877-390-9857 | brushwolf.com... - Page 21 ONLY USE GENUINE OEM PARTS. ORDER PARTS FROM BRUSH WOLF AT 877-390-9857 ITEM PART ITEM DESCRIPTION NUMBER 15054 PLATE, ACCESS, 2 HOLE, 5.250 X 3.250 X 0.250 15067 GUARD, COUPLING, BW, STD 16916 WELDMENT, FRAME, BW 7801 15597 HOSE WHIP ASSEMBLY, -8 ORFS, FEMALE SWIVEL COUPLINGS, 0.750 X 78.000 HOSE...
-
Page 22: 7801 Hf
PARTS: 7801 HF 37 2X 34 8X 25 4X DETAIL A 877-390-9857 | brushwolf.com... - Page 23 ONLY USE GENUINE OEM PARTS. ORDER PARTS FROM BRUSH WOLF AT 877-390-9857 ITEM PART ITEM DESCRIPTION NUMBER 15054 PLATE, ACCESS, 2 HOLE, 5.250 X 3.250 X 0.250 15067 GUARD, COUPLING, BW, STD 15418 PLATE, STAUFF, 3 HOLE COVER, 1.25 X 5.875...
- Page 24 1. 5 - Y E A R L I M I T E D W A R R A N T Y Warranties are valid from date of purchase with a warranty registration on file. Go to www.brushwolf.com for warranty details or scan the QR code. To file a warranty claim, call Brush Wolf at 877-390-9857 or email info@brushwolf.com.
Need help?
Do you have a question about the 7201 LF and is the answer not in the manual?
Questions and answers