IBM 29 CARD PUNCH Maintenance Manual page 86

S225-3357-3
FES: SS234069
Interposer Selection Failure
Flowcharts 1-5
lncorrect Punchout
1-5
Key Pressure Adjustments 4-39
Key Unit
Adjustments 4-39
Removals 4 4 0
Keyboard
Checks, Adjustments, and Removals 4-37
Contacts 4-37
Hook Support Bar 4-38
Installation 2-1
Key Pressure 4-39
Keystem 4-38
Keytop 4 4 0
Latch Pull-Bar 4 4 1
Locations 6-1
L
Lubrication 3-8
Microswitches 4-38
Permutation Bar 4-38
L
Restore Magnet 4-38
Keybutton Tool 4 4 0
Keystem Removals 4-40
Keytop Removals 4 4 0
L
Latch Assembly, Keyboard, Removals 4-40
Latch Magnet Adjustments 4-5
Latch Pull-Bar Removals 4-41
Left-Zero
Difficult Failures 1-1 1
lncorrect Punchout
1-1 1
Loss of Bits 1-1 1
Overflow 1-1 1
Locations
Figures
6-5
Front 6-7
Front, Top
6-5
Keyboard 6-1
Rear (Reed-Relay) 6-5
Rear (WireContact Relay), Bottom 6 6
Rear, Top 6-6
Reed Relay 6-2
\
Reed-Relay Description 6-1
Relay Board 6-2
Relay Gate 6 4
SMS 6-3
't
WireContact Relay 6-3
Loss of Bits, Left-Zero 1-1 1
Lubricants 3-1
Lubrication
' c
Code Plate 4-22
Front 3 4
Front (Tilted) 3-5
Keyboard 3-8
Lubricants 3-1
Motor 4-1
Preventive Maintenance 3-1
Printwire 4-35
Punch Drive 3-7
Rear 3-6
Right Front 3-3
Magazine Springs, Hopper 4-4
Master
Card Guide 4-7
Feed Wheel 4-9
Registration
4 4
Motor
Belt 4-1
Drive 4-1
Lubrication 4-1
Preventive Maintenance 3-2
Operations
General 1-1
Sequence 1-1
Permutation Bar Adjustments 4-38
Pin Bail Arm Adjustments 4-17
Pin Bail Drive Link
Adjustments 4-16
Service Checks 4-17
Pin-Sense
Checks and Adjustments 4-16
Removals
4-18
Throat 4-17
Power
Features 5-1
Installation 2-1
Reference Data 5-1
Re-punch Adjustments 4-5
Ressure Rail
Adjustments 4-6
Card Lever 4-6
Microswitch 4-6
Strap Contact 4-6
Without Contact 4-6
Ressure Roll
Card Feed, Pre-punch 4-5
Punch, Detail 4-7
Read, Master 4-7
Preventive Maintenance
Adjustments 3-1
Cleaning 3-1
Features 3-8
General. 3-1
Lubrication 3-1
Routines 3-2
Safety
3-1
Print
Alignment 4-29
Checks and Adjustments 4-22
Code Plate 4-22
Drive 4-36
Drive Rod, Vertical 4-3 1
Head 4-33
Interposers 4-29
Pressure 4-33
Punch Drive 4-1 1
Removals 4-33
Ribbon Feed 4-36
Service Checks 4-22
Suppression 4-36
Wire 4-34
Yoke 4-29
R i n t Alignment Tools 4-29
R i n t Suppress Magnet
Adjustment 4-36
Shims 4-36
Rint Test Patterns (Fig) 4-34
Rint Wire
Lubrication 4-35
Removals 4-34